10 rue de Leicester 67000 STRASBOURG – France
Technical Data Sheet
ISPOCAN SPRAY 10
DESCRIPTION
ISPOCAN SPRAY 10 is the latest development canister designed to be self-contained and portable. This enables you
to apply adhesive both in your workshop and on site. The canister when equipped with a re-useable hose and gun
eliminates the need for air application systems.
It provides a fast, strong and permanent waterproof bond to substrates.
Product Specification:
High Strength Spray Contact Adhesive:
- No Methylene Chloride
- Tough Aggressive bond
- High Heat resistance (up to 95°C)
- Waterproof
- Fine Even Spray
- Non-Staining
- Dries Clear
- High Green Strengh
- Fast Tack
TECHNICAL DATA
Colour
Appearance
Solids content
Specific gravity
Coverage (13Kg Canister)
Clear or red
Liquid
25-27%
0,8 kg/L
~ 87m2 (Dry Coat weight of 25 gm-2
PACKAGING
Aerosol 500ml
Carboy 13kg
WHERE TO USE
The adhesive is suitable for use in many different industries such as woodworking, furniture, lamination, marine,
caravan, upholstery, construction and can be used to bond, wood, metals, laminates, rubber, foam, fabrics,
polythene, concrete etc.
Do No Use on flexible or plasticized PVC.
ISPO France SARL Siège social : 3 rue de Bitschhoffen 67350 LA WALCK France
 +33 (0) 388 60 80 20 /  +33 (0) 388 60 80 29 / E-Mail : info@ispo-group.com
SIRET : 799 732 292 00013
1/3
INSTRUCTION FOR USAGE
USE IN A WELL VENTILATED AREA
1. Surfaces to be bonded should be clean, dry and free from dust and grease.
2. Substrates should be conditioned before assembly. This is particularly important with laminates. Condition for
48 hours at 20°C with a relative humidity of 45-55%. Air should be able to circulate freely around the components.
3. Connect the hose to the canister and the spray gun to the hose and tighten the connections.
4. Open the valve on the canister. The valve should remain open until the canister is used up. Use the locking nut
on the gun after use. Turning off the valve will result in the adhesive drying in the hose and gun causing blockages.
5. Hold the spray gun at 90° to the surface and apply a uniform generous coat of adhesive, ensuring 80-100%
coverage.
6. Move the gun in parallel to the surface and pay particular attention to the edges.
7. Do not allow the adhesive to puddle as this can cause an unevenness that can “show” through the laminate.
8. On porous surfaces it may be necessary to apply a second coat. Always apply to the laminate first and spray one
substrate horizontally and the other vertically.
9. It is important to remember that ISPOCAN SPRAY 10 is a contact adhesive and forms a bond by sticking to itself,
so there must be sufficient adhesive on both surfaces for this to happen.
10. Allow the adhesive to tack up and protect from contamination whilst this happens. The adhesive is ready to
bond when it feels dry to be touch and does not transfer to the finger tips.
11. Once the two surfaces have been brought together, and aggressive bond will be made. Spacers can be used to
ensure the surfaces do not come into contact prematurely.
12. On the two surfaces are brought together, apply an uniform pressure over the work piece, starting in the
middle and working outwards. Use blocks or a 3 inch roller and ensure the whole piece has been worked to enure
adequate contact of the adhesive.
13. Pay particular attention to the edges. Please note that testing at this point by lifting the edge will weaken the
bond. A nip roller will give the best result.
14. Once assembled, the piece can be machined or trimmed as required.
15. Full cure will take 24 hours.
CLEANING
ISPOCAN SPRAY 10 can be removed with ISPO Citrus Cleaner.
Storage and Shelf Life
Protect from extremes of temperature in a controlled environment between 15 and 35°C, and away from direct
sunlight. Do not stand on a cold concrete floor. Low temperature can result in low adhesive coat weights and poor
bonds. If canisters are subjected to low temperatures the adhesive will thicken and sometimes separate from the
propellant. After bringing the canister back to room temperature, shake or roll the canister to mix adhesive and
propellant.
Stored under the correct conditions, in original, unopened containers, the product will have a shelf life of 12
months.
* Dependent upon test procedure.
OTHER INFORMATION
Legal notes
The information, and in particular, the recommendations relating to the application and end-use of our products, are given in
good faith bases on our current knowledge and experience of the products when properly stored, handled and applied under
normal conditions in accordance with our recommendations. In practice, the differences in materials, substrates and actual site
conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising
out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations,
or from any other advice offered. The user of the product must test the product’s suitability for the intended application and
purpose. ISPO reserves the right to change the properties of its products. The proprietary rights of third parties must be
observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent
issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.
For further information please send an email to info@ispo-group.com.
2/3
10 rue de Leicester 67000 STRASBOURG – France
WARRANTY STATEMENT
ISPO warrants that its products will conform to ISPO specifications at the time of application or use. The products must be
stored in accordance with ISPO recommendations, and used or applied before the earliest of expiration date of such other
period or recommended storage time stated in ISPO products literature. If notified, in writing of a claim within three months of
the product’s delivery or application, ISPO will, at its option, replace or refund the purchase price of ISPO products which does
not satisfy the foregoing warranty.
The foregoing shall constitute the sole and exclusive remedy for defects or failure of the products, and the sole and exclusive
liability of ISPO the warranties stated above are in lieu of all other warranties written or oral, statutory, express or implied,
including any warranty of merchantability or fitness for purpose.
Limitation of liability
ISPO shall, in no event, whether the claim is based on warranty, contract, tort, strict liability, negligence or otherwise, be liable
for incidental or consequential damages, or for any damages in excess of the amount of the purchase price.
ISPO France SARL Siège social : 3 rue de Bitschhoffen 67350 LA WALCK France
 +33 (0) 388 60 80 20 /  +33 (0) 388 60 80 29 / E-Mail : info@ispo-group.com
SIRET : 799 732 292 00013
3/3