FERROUS ALLOYS BACK ALLOYING ADDITIONS IRON & STEEL ir G HENDERIECKX GIETECH BV ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS CONTENT 1. GRAIN SIZE 2. CONTENT OF SPECIFICATIONS 1. GRAIN SIZE Alloy FeB FeCr FeCrSi FeMn FeMnSi FeMo FeNb(Ta) FeP FeSi FeTi FeV FeW + x 0 – 3,15 + + + + + + + + + + + X 0,6 – 6,3 X + + X X + + X Size in mm 3,15 - 25 X X X X X X X X X X X 3,15 - 50 X X X X X X X X X X X 10 - 100 Suitable for metalstream and ladle addition Suitable for furnace adition ir G Henderieckx GIETECH BV September 2004 X X X X X X FERROUS ALLOYS 2. CONTENT OF SPECIFICATIONS FeSi75 FeSi10 FeSi25 FeSi45 FeSi75-Al1 FeSi90 FeSi90-Al1 Si98 Go to Go to Go to Go to Go to Go to Go to Go to FeCr70C01 FeCr70C02 FeCr70C04 FeCr70C06 FeCr70C08 FeCr70C10 FeCr70C50 FeCr70NC10 Go to Go to Go to Go to Go to Go to Go to Go to CaSi CaSiC50 FeSi75 (inoc) FeMn85C01 FeMn85C01P015 FeMn85NC01 FeMn85NC01P015 FeMn80C1 FeMn80NC1 FeMn75C7 FeMn75C7P015 FeMn65Si FeMn70Si Mn97 FeMo70 FeMo62 Al Ni Cu FeV60 FeV80 FeB16 FeB18 FeB12C FeB17C SiC90 FeW1C FeW0,1C Sn Graphite electrod Petroleum cokes High sulphur PET cokes Metallurgical cokes Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to FeCr70C1 FeCr70C1,5 FeCr70C2 FeCr70C4 FeCr70C5 FeCr70C8 FeCr70C6Si FeCr40Si FeCr60Si Cr99 FeNi25 FeNi25C FeNi25CS FeNi55 Mg Mg15Ni85 Mg15Ni69Fe15 Mg5Si47Fe45 Mg10Si45Fe42 Mg30Si55Fe12 Mg10Si55Ca39 FeTi30 FeTi40 FeTi50 FeTi70 FeP24 FeNb65 FeNb60Ta Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to Go to ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO SILICON for alloying STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER FeSi 75 0.3375 COMPOSITION C % NOMINAL RANGE MIN MAX 0,1 Si % 75 73,0 79,0 Fe % 24 P % S % Al % 0,05 0,04 1,0 2,0 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,8 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1210 - 1315 °C + 4,9 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very easy with increase of temperature + Does not evaporate, putting it in the metal bath + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : FERRO SILICON for alloying NAME STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER FeSi 10 0.3310 COMPOSITION NOMINAL RANGE MIN MAX C % 2,5 Si % 10 8,0 15,0 Fe % 87 P % S % Al % 0,15 0,04 0,8 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very easy with increase of temperature + Does not evaporate, putting it in the metal bath + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : FERRO SILICON for alloying NAME STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER FeSi 25 0.3325 COMPOSITION NOMINAL RANGE MIN MAX C % 0,8 Si % 25 20,0 30,0 Fe % 74 P % S % Al % 0,08 0,04 0,8 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very easy with increase of temperature + Does not evaporate, putting it in the metal bath + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : FERRO SILICON for alloying NAME STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER FeSi 45 0.3345 COMPOSITION NOMINAL RANGE MIN MAX C % 0,2 Si % 45 42,0 48,0 Fe % 54 P % S % Al % 0,05 0,04 1,5 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 5,1 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1215 - 1300 °C - 10,0 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very easy with increase of temperature + Does not evaporate, putting it in the metal bath + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : FERRO SILICON for alloying NAME STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER FeSi 75-Al1 0.3376 COMPOSITION C % NOMINAL RANGE MIN MAX 0,1 Si % 75 73,0 79,0 Fe % 24 P % S % Al % 0,05 0,04 1,0 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,8 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1210 - 1315 °C + 4,9 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very easy with increase of temperature + Does not evaporate, putting it in the metal bath + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : FERRO SILICON for alloying NAME STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER FeSi 90 0.3390 COMPOSITION NOMINAL RANGE MIN MAX C % 0,1 0,1 Si % 90 87,0 95,0 Fe % 9 P % S % Al % 0,04 0,04 1,0 2,5 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,4 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1210 - 1280 °C + 12,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very easy with increase of temperature + Does not evaporate, putting it in the metal bath + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : FERRO SILICON for alloying NAME STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER FeSi 90-Al1 0.3391 COMPOSITION NOMINAL RANGE MIN MAX C % 0,1 0,1 Si % 90 87,0 95,0 Fe % 9 P % S % Al % 0,04 0,04 1,0 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,4 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1210 - 1280 °C + 12,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very easy with increase of temperature + Does not evaporate, putting it in the metal bath + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : SILICON for alloying NAME STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER Si 98 0.3398 COMPOSITION Ca % NOMINAL RANGE MIN MAX 0,35 Si % 98 97,0 99,0 Fe % P % 0,5 S % Al % 1,5 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,3 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1410 - 1440 °C + 17,0 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very easy with increase of temperature + Does not evaporate, putting it in the metal bath + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : SILICON for alloying NAME STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER SiC 90 COMPOSITION NOMINAL RANGE MIN MAX C % 30 Si % 67 Fe % 0,2 P % S % Al % 0,3 0,06 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 3,0 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions > 1500 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very slowly + Does not evaporate, putting it in the metal bath + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the de-oxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : CALCIUM SILICON for alloying NAME STANDARD STANDARD NAME DIN 17580 (DEC 1968) WERKSTOFFNUMMER CaSi 0.3650 COMPOSITION NOMINAL RANGE MIN MAX C % Si + Ca % 90 1,20 90,0 Ca % 30 29,0 33,0 P % S % Al % 0,070 0,060 1,80 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,5 kg / dm 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 980 - 1200 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very slowly + Does not evaporate, putting it in the metal bath; creates liquid slag + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : CALCIUM SILICON, low carbon NAME STANDARD STANDARD NAME DIN 17580 (DEC 1968) WERKSTOFFNUMMER CaSiC50 0.3655 COMPOSITION NOMINAL RANGE MIN MAX C % Si + Ca % 90 0,50 90,0 Ca % 30 29,0 33,0 P % S % Al % 0,070 0,060 1,80 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 2,5 kg / dm3 3,15 to 35 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 980 - 1200 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very slowly + Does not evaporate, putting it in the metal bath; creates liquid slag + Melting with a : Acid Lining : Si-content will increase if C, Cr, Mn, Al and or Ti is present. The more oxygen in the metal, the lower the increase Basic Lining : small decrease of Si-content due to the deoxidising effect (SiO2), which will stick to the lining. Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR : : FERRO SILICON for inocculation NAME STANDARD STANDARD NAME DIN 17560 (DEC 1965) WERKSTOFFNUMMER FeSi 75 0.3375 COMPOSITION C % NOMINAL RANGE MIN MAX 0,1 Si % 75 73,0 79,0 Fe % 24 P % S % Al % 0,05 0,04 1,0 2,0 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,8 kg / dm 3,15 to 10 mm 8 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1210 - 1315 °C + 4,9 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very easy with increase of temperature + Does not evaporate, putting it in the metal bath Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM low carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 01 0.4010 COMPOSITION C % 0,010 NOMINAL RANGE MIN MAX 0,010 Si % 0,60 1,50 Cr % 72 65 75 Fe % 26 P % S % N % 0,030 0,010 0,050 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,35 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1600 - 1650 °C - 19,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM low carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 02 0.4011 COMPOSITION C % 0,010 NOMINAL RANGE MIN MAX 0,020 Si % 0,60 1,50 Cr % 72 65 75 Fe % 26 P % S % N % 0,030 0,010 0,050 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,35 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1600 - 1650 °C - 19,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM low carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 04 0.4012 COMPOSITION C % 0,010 NOMINAL RANGE MIN MAX 0,040 Si % 0,60 1,50 Cr % 72 65 75 Fe % 26 P % S % N % 0,030 0,010 0,050 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,35 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1600 - 1650 °C - 19,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM low carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 06 0.4013 COMPOSITION C % 0,010 NOMINAL RANGE MIN MAX 0,060 Si % 0,60 1,50 Cr % 72 65 75 Fe % 26 P % S % N % 0,030 0,010 0,050 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,35 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1600 - 1650 °C - 19,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM low carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 08 0.4015 COMPOSITION C % 0,010 NOMINAL RANGE MIN MAX 0,080 Si % 0,60 1,50 Cr % 72 65 75 Fe % 26 P % S % N % 0,030 0,010 0,050 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,35 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1600 - 1650 °C - 19,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM low carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 10 0.4016 COMPOSITION C % 0,010 NOMINAL RANGE MIN MAX 0,10 Si % 0,60 1,50 Cr % 72 65 75 Fe % 26 P % S % N % 0,030 0,010 0,050 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,35 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1600 - 1650 °C - 19,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM low carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 50 0.4017 COMPOSITION C % 0,010 NOMINAL RANGE MIN MAX 0,50 Si % 0,60 1,50 Cr % 72 65 75 Fe % 26 P % S % N % 0,030 0,010 0,050 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,35 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1590 - 1650 °C - 19,7 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM low carbon, nitrogen STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70N C 10 0.4020 COMPOSITION C % 0,05 NOMINAL RANGE MIN MAX 0,10 Si % 0,60 1,50 Cr % 70 60 72 Fe % 26 P % S % 0,030 0,010 N % 3,0 2,50 4,0 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,35 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1600 - 1650 °C - 19,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM medium carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 1 0.4030 COMPOSITION C % NOMINAL RANGE MIN 0,50 MAX 1,00 Si % 0,60 1,50 Cr % 70 65 72 Fe % 27 P % S % 0,030 0,050 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,34 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1580 - 1610 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM medium carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 1,5 0.4032 COMPOSITION C % NOMINAL RANGE MIN 1,00 MAX 1,50 Si % 0,60 1,50 Cr % 70 65 72 Fe % 27 P % S % 0,030 0,050 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,34 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1580 - 1610 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM medium carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 2 0.4036 COMPOSITION C % NOMINAL RANGE MIN 1,50 MAX 2,00 Si % 0,60 1,50 Cr % 70 65 72 Fe % 26 P % S % 0,030 0,050 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,31 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1400 - 1500 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM medium carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 4 0.4038 COMPOSITION C % NOMINAL RANGE MIN 2,00 MAX 4,00 Si % 0,60 1,50 Cr % 69 65 72 Fe % 25 P % S % 0,030 0,050 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,20 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1360 - 1420 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM high carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 5 0.4052 COMPOSITION C % NOMINAL 6 RANGE MIN 4,0 MAX 6,0 Si % 0,60 1,50 Cr % 64 60 72 Fe % 28 P % S % 0,030 0,050 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,10 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1350 - 1500 °C - 24,9 °C (+/- 4°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM high carbon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 8 0.4056 COMPOSITION C % NOMINAL 8 RANGE MIN 7,0 MAX 10,0 Si % 0,60 1,50 Cr % 64 60 72 Fe % 28 P % S % 0,030 0,030 0,050 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,10 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1350 - 1400 °C - 24,9 °C (+/- 4°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO CHROMIUM high carbon, silicon STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 70 C 6Si 0.4058 COMPOSITION C % NOMINAL 6 RANGE MIN 4,0 MAX 8,0 Si % 1,50 10,0 Cr % 64 60 72 Fe % 28 P % S % 0,030 0,030 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 6,70 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1400 - 1500 °C °C (+/- 4°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : SILICO CHROMIUM STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 40 Si 0.4070 COMPOSITION C % NOMINAL RANGE MIN MAX 0,050 Si % 40 35 45 Cr % 42 40 45 Fe % 16 P % S % 0,020 0,010 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 5,30 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1300 - 1400 °C - 16,9 °C (+/- 4°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : SILICO CHROMIUM STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER FeCr 60 Si 0.4072 COMPOSITION C % NOMINAL RANGE MIN MAX 0,050 Si % 30 20 35 Cr % 60 55 65 Fe % 16 P % S % 0,020 0,010 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 5,80 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1500 - 1600 °C - 22,7 °C (+/- 4°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : CHROME METAL STANDARD STANDARD NAME DIN 17565 (DEC 1968) WERKSTOFFNUMMER Cr 99 0.4090 COMPOSITION C % Si % NOMINAL RANGE MIN MAX 0,030 0,10 Cr % 99 99,0 99,3 Fe % 0,020 P % 0,020 S % Al % 0,035 0,10 0,30 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,20 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1850 °C - 21,5 °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves best if temperature is TL + (100 – 150) °C and quick and good mixing + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon or ferromanganese + Melting in furnace with : Acid Lining : will go in the slag, recovery 98 to 96 % Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MANGANESE low carbon STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 85 C 01 0.3185 COMPOSITION C % NOMINAL 0,50 RANGE MIN 0,05 MAX 0,50 Si % 1,50 1,00 1,50 Mn % 85 80 92 Fe % 13,5 P % S % 0,25 0,030 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 7,30 kg / dm 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1240 °C - 18,3 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves ver good + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon + Melting in furnace with : Acid Lining : will go in the slag Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MANGANESE low carbon & low phosphor STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 85 C 01P015 0.3186 COMPOSITION C % NOMINAL 0,50 RANGE MIN 0,05 MAX 0,50 Si % 1,50 1,00 1,50 Mn % 85 80 92 Fe % 13,5 P % S % 0,15 0,030 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,30 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1240 °C - 18,3 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves ver good + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon + Melting in furnace with : Acid Lining : will go in the slag Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MANGANESE low carbon & nitrogen STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 85 NC 01 0.3187 COMPOSITION C % NOMINAL 0,50 RANGE MIN 0,05 MAX 0,50 Si % 1,50 1,00 1,50 Mn % 85 80 92 Fe % 13,5 P % S % 0,25 0,030 N % 2,5 2,0 2,5 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,30 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1240 °C - 18,3 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves ver good + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon + Melting in furnace with : Acid Lining : will go in the slag Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MANGANESE low carbon & low phosphor & nitrogen STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 85NC 01P015 0.3188 COMPOSITION C % NOMINAL 0,50 RANGE MIN 0,05 MAX 0,50 Si % 1,50 1,00 1,50 Mn % 85 80 92 Fe % 13,5 P % S % 0,15 0,030 N % 2,50 2,00 2,50 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,30 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1240 °C - 18,3 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves ver good + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon + Melting in furnace with : Acid Lining : will go in the slag Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MANGANESE medium carbon STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 80 C 1 0.3180 COMPOSITION C % NOMINAL 2,00 RANGE MIN 0,50 MAX 2,00 Si % 1,00 0,50 1,50 Mn % 80 75 85 Fe % 17 P % S % 0,25 0,030 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,40 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1150 – 1190 °C - 18,7 °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves ver good + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon + Melting in furnace with : Acid Lining : will go in the slag Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MANGANESE medium carbon & nitrogen STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 85 NC1 0.3181 COMPOSITION C % NOMINAL 2,00 RANGE MIN 0,50 MAX 2,00 Si % 1,00 0,50 1,50 Mn % 85 80 90 Fe % 17 P % S % 0,25 0,030 N % 2,0 1,0 2,0 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,40 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1150 - 1190 °C - 18,7 °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves ver good + Does not evaporate, putting it in the metal bath + It oxydies very easy, especially if no other deoxidising elements are present, therefore bring it in after partly deoxidising with ferro-silicon + Melting in furnace with : Acid Lining : will go in the slag Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MANGANESE high carbon STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 75 C 7 0.3175 COMPOSITION C % NOMINAL 7,0 RANGE MIN 6,0 MAX 8,0 Si % 1,00 1,50 Mn % 78 75 80 Fe % 14 P % S % 0,35 0,030 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,30 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1070 - 1260 °C - 18,7 °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + + + + Dissolves ver good Strong tendency to evaporate, putting it on top of the liquid metal bath It oxydies in contact with the air Melting in furnace with : Acid Lining : Enters easily in the slag Increasing C and Cr does increase the recovery (stainless steel: 95 %, high manganese steel: 50 – 60 %) High tendency to react with SiO2 Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MANGANESE high carbon, low posphorus STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 75 C 7P015 0.3177 COMPOSITION C % NOMINAL 7,0 RANGE MIN 6,0 MAX 8,0 Si % 1,00 1,50 Mn % 78 75 80 Fe % 14 P % S % 0,15 0,030 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 7,30 kg / dm 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1070 - 1260 °C - 18,7 °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + + + + Dissolves ver good Strong tendency to evaporate, putting it on top of the liquid metal bath It oxydies in contact with the air Melting in furnace with : Acid Lining : Enters easily in the slag Increasing C and Cr does increase the recovery (stainless steel: 95 %, high manganese steel: 50 – 60 %) High tendency to react with SiO2 Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : SILICO MANGANESE STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 65 Si 0.3160 COMPOSITION C % NOMINAL 0,5 RANGE MIN 0,1 MAX 0,5 Si % 30 23 35 Mn % 65 58 72 Fe % 3 P % S % 0,20 0,010 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 6,10 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1270 - 1280 °C - 16,9 °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + + + + Dissolves ver good Strong tendency to evaporate, putting it on top of the liquid metal bath It oxydies in contact with the air Melting in furnace with : Acid Lining : Enters easily in the slag Increasing C and Cr does increase the recovery (stainless steel: 95 %, high manganese steel: 50 – 60 %) High tendency to react with SiO2 Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : SILICO MANGANESE STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER FeMn 70 Si 0.3162 COMPOSITION C % NOMINAL 2,0 RANGE MIN 0,5 MAX 2,0 Si % 20 15 25 Mn % 70 65 75 Fe % 3 P % S % 0,20 0,010 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 6,30 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1130 - 1240 °C - 17,4 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + + + + Dissolves ver good Strong tendency to evaporate, putting it on top of the liquid metal bath It oxydies in contact with the air Melting in furnace with : Acid Lining : Enters easily in the slag Increasing C and Cr does increase the recovery (stainless steel: 95 %, high manganese steel: 50 – 60 %) High tendency to react with SiO2 Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : MANGANESE METAL STANDARD STANDARD NAME DIN 17564 (DEC 1968) WERKSTOFFNUMMER Mn 97 0.3197 COMPOSITION C % Si % NOMINAL RANGE MIN MAX 0,030 0?50 Mn % 97 95 98 Fe % 3 P % S % 0,050 0,008 N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 7,80 kg / dm3 3,15 to 50 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1220 - 1240 °C - 18,3 °C (+/- 1°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + + + + Dissolves ver good Strong tendency to evaporate, putting it on top of the liquid metal bath It oxydies in contact with the air Melting in furnace with : Acid Lining : Enters easily in the slag Increasing C and Cr does increase the recovery (stainless steel: 95 %, high manganese steel: 50 – 60 %) High tendency to react with SiO2 Basic Lining : recovery nearly 100 % Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MOLYBDENUM STANDARD STANDARD NAME DIN 17561 (DEC 1965) WERKSTOFFNUMMER FeMo 70 0.4270 COMPOSITION C % NOMINAL RANGE MIN MAX 0,10 Si % 0,5 1,00 Mo % 70 60 75 Fe % 29 P % S % Cu % 0,10 0,10 0,50 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 9,40 kg / dm 3,15 to 25 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1800 - 1900 °C - 10,8 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO MOLYBDENUM STANDARD STANDARD NAME DIN 17561 (DEC 1965) WERKSTOFFNUMMER FeMo 62 0.4262 COMPOSITION C % NOMINAL RANGE MIN MAX 0,50 Si % 2,0 2,0 Mo % 62 58 65 Fe % 36 P % S % Cu % 0,10 0,10 1,00 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 9,00 kg / dm 3,15 to 25 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1800 - 1900 °C - 10,8 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO NICKEL STANDARD STANDARD NAME DIN 17561 (DEC 1965) WERKSTOFFNUMMER FeNi 25 0.4425 COMPOSITION C % Si % NOMINAL RANGE MIN MAX 0,030 0,05 Ni + Co % 25 20 30 Fe % P % S % Cr % 0,030 0,040 0,10 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 kg / dm 3,15 to 25 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO NICKEL, high carbon STANDARD STANDARD NAME DIN 17561 (DEC 1965) WERKSTOFFNUMMER FeNi 25C 0.4427 COMPOSITION C % NOMINAL RANGE MIN MAX 2,0 Si % 4,0 Ni + Co % 25 20 28 Fe % P % S % Cr % 0,040 0,040 2,0 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 kg / dm 3,15 to 25 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO NICKEL, high carbon & sulphur STANDARD STANDARD NAME DIN 17561 (DEC 1965) WERKSTOFFNUMMER FeNi 25CS 0.4429 COMPOSITION C % NOMINAL RANGE MIN MAX 2,0 Si % 4,0 Ni + Co % 25 20 28 Fe % P % S % Cr % 0,040 0,30 2,0 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX kg / dm3 3,15 to 25 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO NICKEL STANDARD STANDARD NAME DIN 17561 (DEC 1965) WERKSTOFFNUMMER FeNi 55 0.4455 COMPOSITION C % NOMINAL RANGE MIN MAX 0,05 Si % 1,0 Ni + Co % 55 50 60 Fe % 44 P % S % Cr % 0,020 0,010 0,050 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 8,3 kg / dm 3,15 to 25 mm 5 % can be smaller, 10 % can be larger but never exceeding 1,5 x dimension in 2 or 3 directions 1425 - 1435 °C - 15 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : ALUMINIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER Al COMPOSITION C % Si % NOMINAL RANGE MIN MAX Al % 100 99,5 Fe % P % S % N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,70 kg / dm Special shape 650 - 675 °C + 18,0 °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves ver good + It oxydies in contact with the air Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : NICKEL STANDARD STANDARD NAME DIN WERKSTOFFNUMMER Ni COMPOSITION C % Si % NOMINAL RANGE MIN MAX Ni % 100 99,9 Fe % P % S % N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 8,90 kg / dm Special shape 1450 - 1475 °C - 12,3 °C (+/- 1°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : COPPER, electrolytic STANDARD STANDARD NAME DIN WERKSTOFFNUMMER Cu COMPOSITION C % Si % NOMINAL RANGE MIN MAX Al % 100 99,9 Fe % P % S % N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 8,96 kg / dm Special shape 1080 - 1095 °C - 10 °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS + Dissolves very good Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : MAGNESIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER Mg COMPOSITION C % Si % NOMINAL RANGE MIN MAX Mg % 100 99,9 Fe % P % S % N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 1,74 kg / dm Special shape 650 °C °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : NICKEL MAGNESIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER 15 Mg 85 Ni COMPOSITION C % Si % NOMINAL RANGE MIN MAX Mg % 15 Ni % 85 P % S % N % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,10 kg / dm Special shape 1050 - 1130 °C °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO NICKEL MAGNESIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER 15 Mg 69 Ni 15 Fe COMPOSITION C % Si % NOMINAL RANGE MIN MAX Mg % 15 Fe % 15 P % S % Ni % 69 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,0 kg / dm Special shape 1050 - 1070 °C °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO SILICON MAGNESIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER 5 Mg 47 Si 45 Fe COMPOSITION C % NOMINAL RANGE MIN MAX Si % 47 Mg % 5 Fe % 45 P % S % Ni % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 4,3 kg / dm Special shape 950 - 1275 °C °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO SILICON MAGNESIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER 10 Mg 45 Si 42 Fe COMPOSITION C % NOMINAL RANGE MIN MAX Si % 45 Mg % 10 Fe % 42 P % S % Ni % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 3,8 kg / dm Special shape 950 - 1245 °C °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRO SILICON MAGNESIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER 30 Mg 55 Si 12 Fe COMPOSITION C % NOMINAL RANGE MIN MAX Si % 55 Mg % 30 Fe % 12 P % S % Ni % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,5 kg / dm Special shape 900 - 1000 °C °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : CALCIUM SILICON MAGNESIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER 10 Mg 55 Si 39 Ca COMPOSITION C % NOMINAL RANGE MIN MAX Si % 55 Mg % 10 Fe % P % S % Ca % 39 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 2,2 kg / dm Special shape 900 - 1100 °C °C (+/- 2°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROBOR STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeB16 0.4816 COMPOSITION C % NOMINAL RANGE MIN MAX 0,10 Si % 1,0 B % 16 15 18 Al % % Mn % P % S % Co % 4,0 0,50 0,005 0,001 0,005 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,7 kg / dm Special shape 1450 - 1500 °C -16,2 °C (+/- 6°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROBOR STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeB18 0.4818 COMPOSITION C % NOMINAL RANGE MIN MAX 0,10 Si % 2,0 B % 18 18 20 Al % % Mn % P % S % Co % 2,0 0,50 0,005 0,001 0,005 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,5 kg / dm Special shape 1450 - 1500 °C -16,9 °C (+/- 5°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROBOR STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeB12C 0.4812 COMPOSITION C % NOMINAL RANGE MIN MAX 2,0 Si % 4,0 B % 12 10 14 Al % % Mn % P % S % 0,50 0,50 0,005 0,1 Co % 0,005 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,7 kg / dm Special shape 1450 - 1500 °C -16,2 °C (+/- 6°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROBOR STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeB17C 0.4817 COMPOSITION C % NOMINAL RANGE MIN MAX 2,0 Si % 4,0 B % 17 14 19 Al % % Mn % P % S % 0,50 0,50 0,005 0,1 Co % 0,005 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,6 kg / dm Special shape 1450 - 1500 °C -14,2 °C (+/- 6°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROTITANIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeTi30 0.4530 COMPOSITION C % NOMINAL RANGE MIN MAX 0,10 Si % 4,0 Ti % 30 28 32 Al % % Mn % P % S % 4,5 1,50 0,050 0,060 Co % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,2 kg / dm Special shape 1315 - 1500 °C -16,4 °C (+/- 4°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROTITANIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeTi40 0.4540 COMPOSITION C % NOMINAL RANGE MIN MAX 0,10 Si % 4,5 Ti % 40 36 40 Al % % Mn % P % S % 6,0 1,50 0,10 0,060 Co % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 5,9 kg / dm Special shape 1335 - 1480 °C -16,3 °C (+/- 4°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROTITANIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeTi50 0.4550 COMPOSITION C % NOMINAL RANGE MIN MAX 0,10 Si % 4,0 Ti % 50 46 50 Al % % Mn % P % S % 7,5 1,0 0,10 0,060 Co % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 5,6 kg / dm Special shape 1270 - 1350 °C -15,4 °C (+/- 4°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROTITANIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeTi70 0.4570 COMPOSITION C % NOMINAL RANGE MIN MAX 0,20 Si % 0,20 Ti % 70 65 75 Al % % Mn % P % S % 2,0 1,0 0,040 0,030 Co % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 5,4 kg / dm Special shape 1070 - 1135 °C -12,3 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROVANADIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeV60 COMPOSITION C % NOMINAL RANGE MIN MAX 0,15 Si % 1,5 V % 60 50 65 Al % As % P % S % Cu % 2,0 0,06 0,06 0,05 0,10 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,9 kg / dm Special shape 1550 - 1600 °C -18,1 °C (+/- 5°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROVANADIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeV80 COMPOSITION C % NOMINAL RANGE MIN MAX 0,15 Si % 1,5 V % 80 78 82 Al % As % P % S % Cu % 1,5 0,06 0,06 0,05 0,10 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,4 kg / dm Special shape 1690 - 1770 °C -17,7 °C (+/- 5°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROPOSPHORUS STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeP24 COMPOSITION C % NOMINAL RANGE MIN MAX 0,10 Si % V % Al % As % 1,0 3,0 P % S % 23 25 0,01 Cu % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 6,4 kg / dm Special shape 1250 - 1350 °C °C (+/- 5°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROWOLFRAM (TUNGSTEN) STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeW1C COMPOSITION C % NOMINAL RANGE MIN MAX Si % W % Mn % 0,6 75 85 0,6 As % P % S % Cu % 0,05 0,05 0,2 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 15,4 kg / dm Special shape 1650 - 2100 °C - 8 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERROWOLFRAM (TUNGSTEN) STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeW0,1C COMPOSITION C % NOMINAL RANGE MIN MAX Si % W % Mn % 0,6 75 85 0,6 As % P % S % Cu % 0,05 0,05 0,2 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 15,4 kg / dm Special shape 1650 - 2100 °C - 8 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRONIOBIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeNb65 COMPOSITION C % NOMINAL RANGE MIN MAX 0,15 Si % Nb % Ta % Al % 2,0 62 68 1,0 2,5 P % S % Cu % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 8,1 kg / dm Special shape 1530 - 1580 °C - 12 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : FERRONIOBIUM STANDARD STANDARD NAME DIN WERKSTOFFNUMMER FeNbTa COMPOSITION C % NOMINAL RANGE MIN MAX 0,15 Si % Nb % Ta % Al % 1,5 60 65 6 8 2,0 P % S % Cu % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 8,4 kg / dm Special shape 1550 - 1600 °C - 12 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : TIN STANDARD STANDARD NAME DIN WERKSTOFFNUMMER Sn COMPOSITION C % NOMINAL RANGE MIN MAX Sb % Sn % Bi % As % 0,02 0,05 P % S % Pb % 99,75 0,08 0,08 OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX 3 7,4 kg / dm Special shape 230 - 240 °C - 5 °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : GRAPHITE STANDARD STANDARD NAME DIN WERKSTOFFNUMMER C Electrod cokes COMPOSITION C % S % NOMINAL RANGE MIN 99,10 MAX 0,02 N % H % Ash % Volatile % % 0,01 0,02 0,30 0,30 % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX kg / dm 3 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : GRAPHITE STANDARD STANDARD NAME DIN WERKSTOFFNUMMER C Petroleum cokes COMPOSITION C % S % NOMINAL RANGE MIN 99,00 MAX 0,80 N % H % Ash % Volatile % % 0,40 0,60 0,20 0,60 % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX kg / dm 3 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : GRAPHITE STANDARD STANDARD NAME DIN WERKSTOFFNUMMER C High sulphur PET cokes COMPOSITION C % S % NOMINAL RANGE MIN 97,00 MAX 2,50 N % H % Ash % Volatile % % 0,20 0,11 0,20 0,80 % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX kg / dm 3 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004 FERROUS ALLOYS MATERIAL NR NAME : : GRAPHITE STANDARD STANDARD NAME DIN WERKSTOFFNUMMER C Metallurgical cokes COMPOSITION C % S % NOMINAL RANGE MIN 90,00 MAX 0,80 N % H % Ash % Volatary % % 1,00 0,25 9,50 1,50 % OTHER PROPERTIES SPECIFIC WEIGHT SIZE MELT RANGE COOLING INDEX kg / dm 3 °C °C (+/- 3°) Temperature change if 1 % of the element is added to a steel (bath) at 1600 °C REMARKS Go to Menu ir G Henderieckx GIETECH BV September 2004
