“Naan Mudhalvan”
Autodesk Fusion 360 Design challenge
Level 1
College/ Institute name:- UNIVERSITY COLLEGE OF ENGINEERING ,PANRUTI
Group ID:-
Student names: CHIDAMBARAM . S , GOVINDHARAJAN . J
Mentor Name:© 2022 Autodesk. All rights reserved.
WORKOUT DUMBBELLS
Introduction
● Fixed weight: Dumbbells that are made with cast iron and coated with rubber or
neoprene, or rigid plastic shells filled with concrete. In both cases, the amount
of weight for each dumbbell is fixed (i.e., nonadjustable)
● Adjustable weight: Dumbbells consisting of a metal bar (for gripping) and weighted
disks (plates) that are added or removed to adjust the amount of weight that can
be lifted. Numerous methods are used to secure the disks to the bar.
● Selector weight: Dumbbells whose weight is mechanically adjusted by turning a dial
or moving a selector pin. These types of weights are similar to adjustable weight
dumbbells in that the weight can be changed.
SCOPE OF WORK
●
●
●
●
●
●
●
●
Dumbbells give you a full-body workout: ...
They are versatile: ...
Dumbbells help you burn more calories: ...
They increase your metabolism: ...
They help tone your body: ...
Dumbbells improve your balance and coordination: ...
They build strength: ...
Dumbbells are convenient:
RESEARCH AND ANALYSIS
●
DUMBBELLS are one of the best pieces of home gym equipment anyone can
own. They take up a very small amount of space and can be used to work
almost every
●
in the body. There are literally hundreds of different exercises you can do with
them but below are the top 5 dumbbell workouts.
● The one exercise everybody knows is the bicep curl. To perform this start with
your feet about shoulder width apart. The weights should be held in each hand
with palms facing inwards. As you lift the weight turn the arm so that the palms
face upwards. Do this in a slow and controlled manner. Lower the dumbbell slowly
and do the same movement with the opposite arm. This is the most effective way to
build up the bicepes
●
If it is the chest you want to improve try the front raise. With a
dumbbell in each hand and thumbs pointing towards each other raise
the weights. Try to get them parallel with the ground and keep the
arms almost straight. Slowly lower them and repeat. This is great for
DESIGN OBJECTIVES(10%)
●
Dumbbells are often used for joint-isolation exercises
such as biceps curls, chest flyes or shoulder raises.
Using dumbbells for full-body, multiplanar movements,
however, can provide a variety of different strength
outcomes. It also offers many benefits for
cardiorespiratory fitness and flexibility
●
The dumbbell doesn’t get enough credit next to its
more popular relative, the barbell. But dumbbell
training has many advantages over barbell training.
DESIGN PROCESS (10%)
● This involves green sand, which is wet content sand
that is naturally bonded. Sand is loaded into a flask,
a pattern is pressed into it, then the pattern is
removed and the mold cavity is ready. The raw cast
iron is then put through a Spectromax Machine to
qualify it and then it's heated at extreme
temperatures.
CREATIVITY AND NOVELTY OF
DESIGN(30%)
1. Sarkar and Chakrabarti’s method does not consider both ‘inputs’ and
‘structure’ (i.e. organ or parts) to ascertain if a product is novel. Below, we
explain this deficiency and the related modification to address it. In their
novelty assessment method, Sarkar and Chakrabarti have used the FBS
and SAPPhIRE models. The construct ‘parts’ in the SAPPhIRE is interpreted
as ‘structure’ in the FBS. The FBS model is used first to ascertain whether
or not a product is novel. For this purpose, the structure of a recent
product is compared with that of previous products.
1. If the structure is same, the product has no novelty. However, as
mentioned above in Section 3.1, a recent product can be novel even if its
structure is same as that of previous products, achieving the same
function. This leads us to propose the second modification: a recent
product is not novel if its both ‘inputs’ and ‘structure’ (i.e. organ or parts)
are same as those of previous products, fulfilling the same function.
Therefore, as shown in Figure 4, we Figure 3.
3. Modification 1: Addition of a step to consider differences only in terms
of inputs. Figure 4. Modification to ascertain whether or not a product is
novel. 8 S. JAGTAP add a modification to Sarkar and Chakrabarti’s method,
replacing the FBS model by the constructs of the SAPPhIRE model, to
AUTODESK SOFTWARE USAGE
(TECHNOLOGY) SPECIFIC SOFTWARE
WORKFLOW (30%)
• The autodesk software that i used is fusion 360, the
workflow process is
listed below:• Sketch
• Extrude
• Cut & Joint
• Assembly
• Drive link & Motion link
• Appearance
• Render
• Animation
IMPACT/USER
EXPERIENCE(20%)
• I had best interactions with fusion 360.
• I love the interface since I’m a newbie but some extra function
and shortcuts were needed
HI RES. IMAGES AND
ANIMATIONS
Autodesk and the Autodesk logo are registered trademarks or trademarks of Autodesk, Inc., and/or its subsidiaries and/or affiliates in the USA and/or other countries. All other brand names, product names, or trademarks belong to their respective holders. Autodesk reserves the
right to alter product and services offerings, and specifications and pricing at any time without notice, and is not responsible for typographical or graphical errors that may appear in this document.
© 2022 Autodesk. All rights reserved.