INSTALLATION INSTRUCTIONS FOR LED REAR ACCENT LIGHT BAR
2010-CURRENT CHEVY CAMARO #900648
Congratulations on your purchase of a high quality PUTCO product.
Should you need any application or technical assistance feel free to call us at: 1-800-247-3974
Monday-Friday 8:00 a.m. - 5:00 p.m. (Central Standard Time)
Contact your PUTCO dealer for other quality accessories.
Please read all instructions before beginning installation and be sure to check that all parts and hardware are
included.
P a r ts L is t
D e s c r ip tio n
L E D R e a r A c c e n t L ig h t B a r
R u b b e r G ro m m e t
M o u n t i n g K it
S c o tc h L o c k s
T o o ls N e e d e d fo r In s ta lla tio n
D r ill
Q ty
½ ” D r ill B it
1
1
1
5
R a tc h e t & S o c k e ts
S o c k e t E x te n s io n
S h o p T o w e ls
V o lt M e t e r
W ir e C u tte r s
W ir e C r im p e r s
M a s k in g T a p e
(ATTENTION: Installation of the LED Rear Accent Light Bar requires you to remove the rear bumper fascia from the vehicle.)
Step 1: Verify kit contents.
Step 2: Remove four screws from rear fender well. Repeat on opposite side.
Step 3: Open trunk and remove plastic covers that are above the taillights and set aside.
Step 4: Unclip factory taillight wiring harnesses from the taillights.
Step 5: With help from an assistant remove the rear bumper fascia
from the vehicle (see figure 1). (Note: Use extreme caution
to not damage the finish of the rear bumper fascia!)
Step 6: Place the rear bumper fascia on a clean non-abrasive surface.
Step 7: Align the LED Rear Accent Light Bar to the rear bumper fascia
so the wires are on the passenger side. Align the four supplied
brackets so they are evenly spaced.
Step 8: Attach the four brackets to the rear bumper fascia using the
supplied hardware kit.
Figure 1
Step 9: Attach the LED Rear Accent Light Bar to the four brackets.
Step 10: Drill a ½” hole into the rear bumper fascia near the end of the LED Rear
Accent Light Bar where the wires are located. (Note: Ensure there is enough
room for the wires to pass through the drilled hole.)
Step 11: Prior to removing the LED Rear Accent Light Bar four pin wire connector,
identify and label each wire (see figure 2). Cut the wires as close to the
connector as possible and discard the connector.
Step 12: Place the rubber grommet over the wires and fuse.
Figure 2
Page 1 of 2
www.putco.com
INSTALLATION INSTRUCTIONS FOR LED REAR ACCENT LIGHT BAR
2010-CURRENT CHEVY CAMARO #900648
Step 13: Run the wires and fuse through the drilled hole (see
figure 3) so they can be accessed from the inside.
Install the grommet into the drilled hole. (Note: If the
grommet is difficult to install, use dish soap to aid
the installation. If that does not work you may
need to drill a larger hole.)
Step 14: Align the LED Rear Accent Light Bar wires to the
factory turn signals, brake light and reverse light
wires.
Step 15: With help from an assistant temporarily install the
Figure 3
rear bumper fascia and connect the factory taillight
wiring harnesses to gain power to the taillights. Use your volt meter to identify the positive (+) and negative (-)
wires that you will need to connect to. Once these have been identified label them for reference in the upcoming
steps. (Note: You will need to have power to the taillights and reverse lights.)
Step 16: Disconnect the factory taillight wiring harnesses and with help from an assistant remove the rear bumper fascia
from the vehicle and place on a non-abrasive surface.
Step 17: Connect the LED Rear Accent Light Bar wires to the factory turn signals, brake and reverse lights using the
supplied scotch locks.
Step 18: With help from an assistant temporarily attach the rear bumper fascia to the vehicle and reconnect the factory
taillight wiring harnesses and test the LED Rear Accent Light Bar. (Note: If the LED Rear Accent Light Bar does
not light up make sure that there is power to the tail lights. You can do this by turning the hazard lights on
or by pressing the unlock button on your key fob. If the LED Rear Accent Light Bar does not light up
recheck all of your connections.)
Step 19: Reassemble the rear bumper fascia using steps 2-5 as a guide.
INSTRUCTION # IN900648-May 2011
LIMITED WARRANTY
Putco guarantees its products against defects in workmanship and material for as long as you own your vehicle. All painted products have a 90 day
warranty on the painted surface. Any defects resulting from faulty material or workmanship will be warranted by Putco and repaired or replaced at our
discretion. Putco assumes no extra labor costs. Damages caused by freight carriers, improper installation, misuse, collision, or neglect will not be warranted
by Putco. Putco is not liable for any vehicle damage resulting from the installation of our LED Rear Accent Light Bar.
Page 2 of 2
www.putco.com