SUGGESTED
MOUNTING
FOR
SUGGESTED
MOUNTING
FOR
®
TECHNISEAL
troffers
TECHNISEAL
TROFFERS
®
FLANGE SERIES F1, F2, F3, F4
Flange
Series
F1,assembly
F2, F3,
F4 all captive screws, squeezing the
1. Remove
lens frame
by loosening
1. Remove
frame
by loosening
all captive
two (2)lens
safety
wire assembly
hinges or unclip
two (2) safety
snells.screws, squeezing the two (2) safety wire
hingesthe
or reflector/ballast
unclip two (2) safety
snells.
2.
Remove
cover by
turning the quarter-turn fasteners.
2.3.Remove
thethe
reflector/ballast
cover
fourto(4)
fasteners.
Remove
tape securing the
four by
(4) turning
swing bars
thequarter-turn
housing.
3.4.Remove
the
tape
securing
the
four
(4)
swing
bars
to
the
housing.
Place luminaire into ceiling opening and turn the four (4) swing bar screws clockwise
4. Place
into ceiling
opening
turn NOTE:
the fourIf (4)
swing
screws
clockwise there
isn't bar
plenum
access
untilluminaire
luminaire pulls
up securely
to theand
ceiling.
it will
be necessary
to connect
completely
installing
luminaire.
until
luminaire
pulls up
securelywiring
to thebefore
ceiling.
NOTE: If
there isn’t
plenum access it will be 5.
Make all to
necessary
necessary
connect wiring
wiringconnections.
before completely installing luminaire.
5.6.Make
all necessary
wiringcover,
connections.
Replace
reflector/ballast
install lamps, safety wire hinges or safety snells and
lens frame
assembly.
6. Replace
the reflector/ballast
cover, install lamps, safety wire hinges or safety snells and lens frame assembly.
GRID SERIES G1, G2, R7
Grid
Series
G1, assembly
G2, R7by loosening all captive screws, squeezing the
1. Remove
lens frame
two (2)lens
safety
wire assembly
hinges or unclip
two (2) safety
snells.screws, squeezing the two (2) 1. Remove
frame
by loosening
all captive
2.
Remove
the
reflector/ballast
cover
by
turning
the
safety wire hinges or unclip two (2) safety snells. quarter-turn fasteners.
3.
Remove
mounting hardware
and
the the
luminaire
into the fasteners.
grid opening.
2. Remove
thethe
reflector/ballast
cover
byplace
turning
quarter-turn
3.4.Remove
mounting
hardware
placebrackets
the luminaire
into the grid opening.
Securethe
luminaire
to "T"
bar usingand
furnished
and screws.
4.5.Secure
to “T”
barconnections.
using furnished brackets and screws.
Makeluminiare
all necessary
wiring
5.6.Make
all necessary
wiringcover,
connections.
Replace
reflector/ballast
install lamps, safety wire hinges or safety snells
and lens
assembly. cover, install lamps, safety wire hinges or safety snells and 6. Replace
theframe
reflector/ballast
lens frame assembly.
SURFACE SERIES S0, S1, S2, S3, S4, S7
1. Remove
lens frameS0,
assembly
all captive
Surface
Series
S1, byS2,loosening
S3, S4,
S7 screws, squeezing the
two (2)lens
safety
wire assembly
hinges or unclip
two (2) safety
snells.screws, squeezing the two (2) 1. Remove
frame
by loosening
all captive
2.
Remove
the
reflector/ballast
cover
by
turning
the
safety wire hinges or unclip two (2) safety snells. quarter-turn fasteners.
3.
Mount the
luminaire
to ceiling utilizing
(4) mounting
holes provided.
2. Remove
reflector/ballast
cover four
by turning
the quarter-turn
fasteners.
Makeluminaire
all necessary
wiring and
connections.
3.4.Mount
to ceiling
utilizing
four (4) mounting holes provided.
Replace
reflector/ballast
install lamps, safety wire hinges or
4.5.Make
all necessary
wiringcover,
connections.
safety the
snells
and lens frame cover,
assembly.
5. Replace
reflector/ballast
install lamps, safety wire hinges or safety snells and Models
lens frame
assembly.
H.O.
require
1-1/2" spacing from mounting surface (Brackets supplied)
H.O. Models require 1-1/2” spacing from mounting surface (Brackets supplied)
MARINE INSIDE DRIP PROOF
SERIESInside
MS0, MS1,
Marine
Drip MS2,
RoofMS3, MS4, MS7
1. Remove lens frame assembly by loosening all captive screws, squeezing the
Surface
Series S0, S1, S2, S3, S4, S7
two (2) safety wire hinges or unclip two (2) safety snells.
1.2.Remove
lens
assembly cover
by loosening
captive
screws,
squeezing the two (2) Remove
theframe
reflector/ballast
by turningallthe
quarter-turn
fasteners.
safety
wire
hinges
or
unclip
two
(2)
safety
snells.
3. Mount luminaire to ceiling utilizing four (4) mounting holes in straps provided.
2. Remove the reflector/ballast cover by turning the quarter-turn fasteners.
4. Make all necessary wiring and connections to supplied terminal block
3. Mount luminaire to ceiling utilizing four (4) mounting holes in straps provided.
5. Replace reflector/ballast cover, install lamps, safety wire hinges or safety snells
4. Make
and all
lensnecessary
assembly.wiring connections.
5. Replace the reflector/ballast cover, install lamps, safety wire hinges or safety snells and lens frame assembly.
Cleaning Instructions: Wipe luminaire with a soft cloth slightly dampened with warm, soapy water.
On stainless steel units, tightly adhering deposits may be removed by using a stainless steel polishing powder.
Never use steel wool or steel brushes on stainless steel. Always rub in the direction of the polish lines.
Note: All luminaires to be installed by a qualified electrician.
Mounting and electrical hardware not supplied by Paramount Industries unless otherwise noted.
PARAMOUNTINDUSTRIES, INC.
Paramount Industries, Inc.
800-521-5405
Fax 800-852-7154
23
www.paramountlighting.com
REVISED 06/2012