PROJECT INFORMATION PERMACELL™ Job Name Fixture Type PC1515 SERIES (F55) Catalog Number PRODUCT FEATURES: Approved by »»Recessed mount – ceiling; 15"W×15L"×8"D »»Die-formed 16-gauge cold rolled steel housing »»14-gauge cold rolled steel lens frame with continuous lens retention system »»Peace of Mind Guarantee® against breakage SPECIFICATIONS HOUSING: Lapped and spot welded construction. Die-formed 16-gauge CRS. White TGIC polyester powder coat – 5-stage pre-treatment. Salt spray test: 1,000 hours; Reflectance: 92%. LENS FRAME: 14-gauge CRS. Continuous lens retention system. White or dark bronze TGIC polyester powder coat finish – 5-step pre-treatment. Salt spray test: 1,000 hours. See Ordering Information for painted or brushed stainless finishes. LENS: As specified. See Ordering Information. REFLECTOR: Compact Fluorescent: Full reflector/wire cover – white finished CRS (92% reflectivity). HID: Full reflector/wire cover. High efficiency textured aluminum. GASKET: Polyurethane foam rubber gasket. HARDWARE: Four stainless steel Torx® with center pin fasteners secure lens frame to housing. ELECTRICAL: Magnetic Compact Fluorescent ballasts power factor corrected. Electronic ballasts high power factor. HID ballasts externally mounted encased and potted high power factor. Medium base shock absorbing lamp socket. INSTALLATION: See Cross Section/Details. LISTINGS: UL and CUL listed for Wet Location. ORDERING INFORMATION (Ex: PC1515-R-GW-42P-1-120-FS) Model Lens Type Lens Frame Finish Lamp Type Lamp Qty Accessories Options PC1515 Lens Type (Inner/Outer) DP Drop Prismatic Polycarbonate DO Drop Opal Polycarbonate 4 0.156" Prismatic Polycarbonate R 0.156" Prismatic Tempered Glass 7 0.187" Clear Polycarbonate 8 0.187" Clear Tempered Glass A 0.250" Clear Tempered Glass 9 0.250" Clear Polycarbonate Lens Frame Finish GW Gloss White (standard) DB Dark Bronze (standard) SB Stainless Steel Duro Bronze (optional) SW Stainless Steel White (optional) SN Stainless Steel Brushed Finish (optional) Lamp Type (Qty/Ballast/Volt./Starting Temp) 13 13 Watt Twin (2,3MB/120,277,347/32°F) 26Q 26 Watt Quad (1,2/RS/120,277,347/0°F) 32P 32 Watt PLT (1,2/RS/120,277,347/0°F) 42P 42 Watt PLT (1,2/RS/120,277,347/0°F) 50S* 50 Watt HPS (1/HPF/120,277,347/-40°F) 70S* 70 Watt HPS (1HPF/120,277,347/-40°F) 70M* 70 Watt MH (1/HPF/120,277,347/-20°F) 100S* I00 Watt HPS (1/HPF/120,277,347/-40°F) 100M* I00 Watt MH (1/HPF/120,277,347/-20°F) 150S* 150 Watt HPS (1/HPF/120,277,347/-40°F) 150I* 150 Watt Incandescent (1/A-19) Voltage 120 120 Volts 277 277 Volts 347 347 Volts (consult factory) DT 120/277 Volts (HID only) Accessories 9009 100 Watt DC Bay Quartz Lamp 9500Torx® Screwdriver Options EL One-Lamp Indoor Battery Pack (32ºF) FS Single Fuse & Holder QR Quartz Restrike System for maximum 100 Watt DC Bay Quartz Lamp (see 9009) * Glass interior lens required Lamp Quantity (See Lamp Type) 1 One Lamp 2 Two Lamps 3 Three Lamps DIMENSIONAL DATA CROSS SECTION/DETAILS MOUNTING VIEW 20.36" 15" 16.25" RECOMMENDED CEILING CUT OUT 20.36" (2) 1/2" EMT KOs 8.63" 6.5" 15.5" *Caution: 5 inch free space above ceiing on one side required for HID ballast overhang. See Cross Section/Details drawing. 15.5" 11.86" (2) .38" Dia. Mounting Holes 20.36" www.kenall.com P: 800-4-Kenall F: 847-360-1781 1020 Lakeside Drive Gurnee, Illinois 60031 When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. Content of specification sheets is subject to change; please consult www.kenall.com for current product details. © 2013 Kenall Mfg. Co. All rights reserved. PC1515-120612