T200 SYSTEM
T200 SYSTEM Cylinder Module & PAR 30 Spotlight Module
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
T200 SYSTEM Indirect/Direct & PAR 30 Spotlight Modules | J. Willard Marriott Library, The University of Utah, Salt Lake City, UT
Architect: MJSA Architecture, Salt Lake City, UT | Lighting Design: Electrical Consulting Engineers, Salt Lake City, UT
T200 SYSTEM Linear Aimable & Metal Halide Spotlight Modules
Tilburg Audi Center, Tilburg, Netherlands
Photograph: Boris Golz
2
T200 SYSTEM PAR 30 Spotlight Modules
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
23
T200 SYSTEM. General accent lighting in one system.
The T200 SYSTEM allows specifiers to strategically position lighting components to provide precise control over
lighting conditions and effects in office, retail, and educational settings. From orchestrating product illumination in retail
environments to adeptly lighting a computer station, T200 SYSTEM’s comprehensive offering of finely crafted fixtures and
lamping options enables the specific placement of high-performance general lighting fixtures. The T200 SYSTEM gives the
tools to achieve a wide range of solutions.
Design flexibility.
Combining T6 metal halide, PAR 30 (halogen or LED) spotlight modules, and any
of three linear T5 fluorescent modules allows specifiers to provide focused lighting of
individual objects or areas, as well as uniform general lighting in one system. The T200
SYSTEM allows two-circuit wiring enabling separate switching of fluorescent and spotlight
modules or the use of two different voltages (120V and 277V).
Tubular track system.
Using spacer tubes and jointed connectors along with the range of luminaires available
enables specifiers to meet a multitude of architectural scenarios and lighting challenges.
PAR 30 and Cylinder Modules
Designing with the T200 SYSTEM.
The T200 SYSTEM’s flexibility makes it adaptive to a multitude of architectural conditions and provides a variety of shapes
and configurations. However since it is a system of components, Énergie recommends that specifiers consult the factory for
assistance in designing with the T200 SYSTEM. The Énergie team will assist with layout and specification of components to be
sure that everything meets the specified design goals.
3
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
T200 SYSTEM Components.
To simplify planning and installation, each of the luminaire components is pre-attached to aluminum tubes to
create a module. Modules may be connected with corner connectors and/or spacer tubes as needed to create the
desired design.
T200 SYSTEM Fluorescent Modules.
Indirect/Direct T5 Module (95% efficient).
The Indirect/Direct Module is a suspended T5 luminaire with a Trilux-designed
louver made from Alanod MIRO-SILVER®® aluminum material. The module is 95%
efficient. The Indirect/Direct module is dimmable and uses 1 or 2 T5/T5HO lamps.
Intensity values at 55° are significantly better with both T5 and T5HO than ANSI/
IES RP-1-04 recommendations. When T5HO is used, a slotted shield reduces direct
brightness.
Indirect/Direct Module
Linear Aimable Module (97% efficient).
The Linear Aimable Module is a T5 luminaire with a specular
50°
parabolic louver that uses one or two T5/T5HO lamps and is up
to 95% efficient. The luminaire body rotates through a 50° angle
from a vertical position. Intensity values at 55° are significantly
better than ANSI/IES RP-1-04 recommendations when aimed
End view
straight down.
Linear Aimable Module
Cylinder Module (86% efficient).
The Cylinder Module is a T5 luminaire with a fixed cylindrical shielding mechanism
that serves as both a diffuser and a reflector. The Cylinder Module uses 1x28W T5
lamping and is 86% efficient.
Cylinder Module
Cylinder Module
4
Cylindrical Shield
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
T200 SYSTEM Spotlight Modules.
Ceramic Metal Halide Spotlight Module.
The Ceramic Metal Halide Spotlight Module uses either a 39W or 70W T6 ceramic
metal halide lamp. The spot can be pivoted in two planes by means of the cardanic
suspension system.
34º
23º
Ceramic Metal Halide Spotlight Module
End view
Side view
PAR 30 Spotlight Module.
The PAR Spotlight Module uses PAR 30 short-neck lamps with a maximum of 75W
or LED PAR 30 lamps. The spotlight can be positioned in two planes by means of the
cardanic suspension system. Modules are available for one, two or three lamps.
43º
23º
End view
PAR 30 Spotlight Module
Side view
T200 SYSTEM Connector Components.
Extruded aluminum Spacer Tubes (1-, 2-, and 3-foot lengths) and Corner
Connector kits (right angle, “T,” and “X”) allow specifiers to lay out the T200 SYSTEM in
highly varied geometric patterns. Connectors are supplied as a kit with all necessary
hardware. Spacer Tubes are supplied in pairs and may be field cut.
2'-0"
Spacer Tubes
1'-6"
2'-0"
2'-0"
1'-6"
1'-6"
= SUPPORT CABLE
90º Corner Connector Kit
“T” Connector Kit
“X” Connector Kit
Connector kits include mounting points
5
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
Product details (all components).
• Accent and/or general lighting in one system
• Flexible arrangement of fluorescent and spotlight
modules to meet design needs
• High-efficiency fluorescent fixtures provide
general lighting
• Spotlights swivel on two axes enabling easy aiming to
highlight objects or areas
• Optional two-circuit wiring enables separate switching of
modules for two voltages
• All modules come mounted on two extruded aluminum
tubes to simplify installation
• Spacer Tubes may be field cut to adapt to design needs
• ”T,” ”X,” and Corner Connector kits enable layouts with
geometric patterns and rectangular shapes
• Intensity values for Indirect/Direct and Linear
Aimable Modules (when aimed straight down) at
55° are significantly better than ANSI/IES RP-1-04
recommendations
T200 SYSTEM Indirect/Direct Module
Construction
Main body of fixture constructed of extruded aluminum alloy. Endcaps are die-cast aluminum.
Tubes are extruded aluminum.
Finish
Extruded body finished with steel-gray powder coat finish.
Shielding
Specular parabolic louver. When T5HO lamping is used, the louver is covered by a slotted
steel shield.
Electrical
120V or 277V. Supplied with integral electronic ballast.
Mounting
Fixture mounts to T200 SYSTEM tubes with available internal tube-joiner sleeve.
T200 SYSTEM Linear Aimable Module
Construction
Luminaire body and side tubes are extruded aluminum. Endcaps are die-cast aluminum. Top of
fixture is open for indirect component. Fixture body rotates through a 50º angle from vertical.
Finish
Luminaire body and endcaps are finished in steel-gray powder coat finish.
Shielding
Lamp is shielded by a specular parabolic louver.
Electrical
120V or 277V. Supplied with integral electronic ballast.
Mounting
Fixture mounts to T200 SYSTEM tubes with available internal tube-joiner sleeve.
T200 SYSTEM Cylinder Module
Construction
Endcaps constructed of high-pressure injection-molded polycarbonate. Tubes are
extruded aluminum.
Finish
Endcaps are finished with steel-gray powder coat finish. Cylinder anchors at the end of the diffuser
are in chrome finish.
Shielding
Lamp is shielded by a fixed cylindrical diffuser/reflector system.
Electrical
120V or 277V. Supplied with integral electronic ballast.
Mounting
Fixture mounts to T200 SYSTEM tubes with available internal tube-joiner sleeve.
See product specification sheets at www.energielighting.com for complete details.
6
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
Product details (continued).
T200 SYSTEM Metal Halide Module
Construction
Main body of fixture constructed of steel. Endcaps constructed of high-pressure
injection-molded polycarbonate.
Finish
Steel body finished with steel-gray roughened finish. Tubes are extruded anodized aluminum.
Shielding
Fixture equipped with heat-resistant glass cover.
Electrical
120V or 277V. Integral electronic ballast.
Mounting
Fixture mounts to T200 SYSTEM tubes with available internal tube-joiner sleeve.
T200 SYSTEM PAR Module
Construction
Main body of fixture constructed of steel. Endcaps constructed of high-pressure
injection-molded polycarbonate.
Finish
Steel body finished with steel-gray powder coat finish. Tubes are extruded anodized aluminum.
Electrical
120V only.
Mounting
Fixture mounts to T200 SYSTEM tubes with available internal tube-joiner sleeve.
T200 SYSTEM Connectors (“T,” “X,” and 90° connectors)
Construction
Hinges are constructed of injection-molded plastic. Tube extensions are extruded aluminum.
Connectors are supplied as a kit with all necessary hardware.
Finish
Connector has a chrome finish. Tube extensions are extruded anodized aluminum.
Electrical
Connector and all electrical components are UL/CUL approved for use with T200 SYSTEM.
Mounting
Fixture mounts to T200 SYSTEM tubes with supplied internal tube-joiner sleeve.
All connectors are supplied with 72-inch fully adjustable aircraft cables and hardware.
T200 SYSTEM Spacer Tubes
Construction
Tubes are constructed of extruded anodized aluminum and have a 1.1-inch diameter. Tubes and
covers are supplied as a pair. Tube covers are extruded plastic.
Finish
Tubes are anodized aluminum and can be field cut.
Electrical
Tubes and all electrical components are UL/CUL approved for use with T200 SYSTEM.
Mounting
Tubes mount to other T200 SYSTEM tubes/components with available internal tube-joiner sleeve.
See product specification sheets at www.energielighting.com for complete details.
7
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
Product details (continued).
T200 SYSTEM: Linear Fluorescent Modules
T200 SYSTEM
Indirect/Direct Module
T200 SYSTEM
Linear Aimable Module
T200 SYSTEM
Cylinder Module
T200-IND
T200-LAM
T200-LIC
Dimming, Switching
Yes
No
No
Indirect % / Direct %
62% / 38%
62% / 38%
76% / 24%
DAMP LOCATION LISTED
Catalog Number Prefix
Efficiency
Lamp
95%
97%
86%
(1x28W T5HO)
(1x28W T5)
(1x28W T5)
1x28W T5
1x54W T5HO
2x28W T5
2x54W T5HO
1x28W T5
1x54W T5HO
2x28W T5
2x54W T5HO
1x28W T5
See product specification sheets at www.energielighting.com for complete details.
T200 SYSTEM: Spotlight Modules
Catalog Number Prefix
T200 SYSTEM
Ceramic Metal
Halide Module
T200 SYSTEM
PAR Single Lamp Module
T200 SYSTEM
PAR Double Lamp Module
T200 SYSTEM
PAR Triple Lamp Module
T200-MHS
T200-PAR1
T200-PAR2
T200-PAR3
Dimming
No
Indirect % / Direct %
n/a
Efficiency
Lamp
Yes
Yes
Yes
(halogen)
(halogen)
(halogen)
n/a
n/a
n/a
n/a
n/a
n/a
1x75W PAR 30
(or LED PAR 30)
short-neck med. base
2x75W PAR 30
(or LED PAR 30)
short-neck med. base
3x75W PAR 30
(or LED PAR 30)
short-neck med. base
71%
1x39W T6
1x39W T6
Metal Halide G85 68.5
1x70W T6
Metal Halide G85 68.5
See product specification sheets at www.energielighting.com for complete details.
8
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
Dimensions.
INDIRECT/DIRECT MODULE
9.0"
2.7"
6.7"
5'- 0"
LINEAR AIMABLE MODULE
9.3"
2.3"
3.7"
5'-0"
CYLINDER MODULE
9.3"
1.4"
2.1"
5'-0"
Performance.
9
For photometric files, visit www.energelighting.com.
INDIRECT/DIRECT MODULE
LINEAR AIMABLE MODULE
CYLINDER MODULE
Indirect: 62%
Direct: 38%
Efficiency: 95%
1x28W T5
Specular Louver
Indirect: 62%
Direct: 38%
Efficiency: 97%
1x28W T5
Specular Louver
Indirect: 76%
Direct: 24%
Efficiency: 86%
1x28W T5
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
METAL HALIDE MODULE
(aimed straight down)
Indirect: 0%
Direct: 100%
Efficiency: 71%
1x39W T6 Metal Halide
Dimensions (continued).
9.3"
CERAMIC METAL HALIDE MODULE
5.7"
2'-0"
5.1"
34º
23º
PAR 30 MODULE
4.6"
9.3"
2'-0"
2'-0"
3'-0"
23º
43º
5.1"
5.1"
5.1"
5.1"
5.1"
5.1"
CORNER CONNECTORS
90º Corner Connector Kit
“T” Connector Kit
“X” Connector Kit
2'-0"
2'-0"
1'-6"
2'-0"
1'-6"
2'-0"
1'-0"
2'-0"
1'-6"
1'-6"
1'-6"
2'-0"
1'-6"
= SUPPORT
= SUPPORT
CABLE CABLE
spacer tubes
10
1'-0"
2'-0"
1' Tube Spacer
2' Tube Spacer
3' Tube Spacer
1'-0"
2'-0"
3'-0"
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
T200 SYSTEM layout examples.
The T200 SYSTEM is a flexible, modular system of components that may be joined together to create multi-purpose
lighting solutions. The examples shown on the following pages are provided to help illustrate the options available to specifiers
to meet a wide range of design objectives. Because the T200 SYSTEM is comprised of many components, Énergie requires
a factory quote to ensure that all necessary components are included.
Example: Rectangle
1'-6"
5'-0"
1'-0"
5'-0"
1'-6"
COMPONENT
1'-6"
QTY
DESCRIPTION
4
Linear Aimable
Module
2
PAR 30, 2-lamp
Module
6
1' Spacer Tube pair
4
Corner Connector
kit
4
Suspension kit
1'-0"
2'-0"
2'-0"
1'-0"
1'-0"
1'-0"
(not shown)
1'-6"
2'-0"
2'-0"
Example: Grid
1'-6"
5'-0"
2'-0"
5'-0"
1'-6"
COMPONENT
QTY
3'-0"
1'-6"
4
Indirect/Direct
Fluorescent Module
3
PAR 30, 3-lamp
Module
2
“T” Connector kit
4
Corner Connector
kit
3'-0"
3'-0"
DESCRIPTION
1'-6"
11
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
T200 SYSTEM layout examples (continued).
COMPONENT
Example: “T” shape
1'-6"
1'-0"
QTY
DESCRIPTION
1
Indirect/Direct
Fluorescent Module
2
PAR 30, 2-lamp
Module
3
PAR 30, 1-lamp
Module
1
"T" Connector kit
2
Corner Connector kit
4
1' Spacer Tube pair
1
2' Spacer Tube pair
4
Suspension kit
2'-0"
1'-6"
1'-0"
2'-0"
2'-0"
5'-0"
2'-0"
2'-0"
2'-0"
1'-0"
1'-0"
1'-0"
1'-6"
(not shown)
2'-0"
2'-0"
Example: Linear Run
5'-0"
1'-0"
2'-0"
2'-0"
5'-0"
1'-0"
3'-0"
3'-0"
COMPONENT
(not shown)
1'-0"
1'-0"
12
Énergie • 4885 Ward Road, Suite 300 • Wheat Ridge, CO 80033 • Tel 720 963 8055 • www.energielighting.com
QTY
DESCRIPTION
2
Cylinder Module
2
Metal Halide
Spotlight Module
2
1' Spacer Tube pair
4
Suspension kit