HCP
FireFinder™ XLS Control Point Module
• Intelligent Device for use with FireFinder XLS Control Panel
• Used as a Telephone Zone, Speaker Zone or
Notification Appliance Circuit
• Provides either a 25V (35 Watts) or 70.7V (25 Watts)
Single Channel Speaker Zone
• Provides 24 VDC Notification Appliance Circuits
• Used with Siemens Fire Safety Notification Appliances
• Firefighters Telephone Circuits
• Polarity Insensitive with SureWire™ Technology
• Internally Power Limited Using Self Restoring Solid
State Thermal Devices
• Supervised DC Input
• Mounts on Standard Electrical Box (Double Gang
or 4" Square)
• No Mechanical Address Programming Required
•
Listed and ULC Listed;
City of Chicago, CSFM, NYMEA (Pending)
Description
The HCP provides an intelligent control point for the
FireFinder XLS Control Panel. The HCP can be programmed as an independent, remotely located telephone zone, speaker zone or notification appliance
circuit. The HCP is designed to be used with the
Siemens Fire Safety notification appliance product line.
The HCP can be programmed for any of the usages
mentioned above using the ZEUS programming
software and controlled by the systems’ output logic.
It can be addressed and tested using the DPU device,
eliminating the need for any mechanical addressing.
The output of the HCP is inherently power limited
using solid state, self-restoring thermal devices.
This 24VDC input to the HCP is supervised by the
HCP itself so that power wiring may include branch
circuits. When programmed as a speaker zone, the
high power audio risers are supervised using the ZAC40 or ZAM-80/180 zone amplifiers. When programmed
as a telephone zone, the telephone riser is supervised
by the TZC-8 module.
The HCP mounts in a standard double gang or 4"
square electrical box.
This equipment is approved for operation over the
temperature range of 0°C to 50°C and relative humidity
range of 93% RH +/- 2% RH at 40°C +/-2°C.
The HCP communicates through the DLC analog loop
and can be wired either Class A (Style Z) or Class B
(Style Y). The 24 VDC power input comes from either
the control panel or from any UL listed power limited,
auxiliary power supply.
CATALOG NUMBER
6311
Mounting Data
4 INCH SQUARE
ELECTRICAL BOX,
2 ½ INCHES DEEP
3 ½ INCH DEEP,
DOUBLE GANG
SWITCHBOX
1 ½ INCH DEEP EXTENSION
OR 1¼ INCH DEEP PLASTER
RING EXTENSION
HCP
HCP
DOUBLE GANG
BLANK SWITCHPLATE
(USER SUPPLIED)
1. Use a standard 31/2" deep, double gang electrical
switchbox or a 4" square electrical box that is 21/2" deep
with either a 1½" deep extension or a 11/4" deep plaster
ring extension.
2. Connect the field wiring. Insert the HCP into the box
and fasten the module plate to the box.
4 INCH SQUARE BLANK
PLATE (USER SUPPLIED)
OR
DOUBLE GANG BLANK
SWITCHPLATE
(USER SUPPLIED)
Note: When using the double gang switchbox or the
plaster ring extension, use the same four screws
to fasten both the module and the blank plate
(user supplied).
3. Cover the module front plate with a 4" blank plate (user
supplied) and fasten with two plate screws.
Please see installation instructions or check the web site
(password protected section), www.cerbpyro.com, for
the current listing of Compatible Notification Appliances.
NOTICE: The use of other than Siemens Fire Safety detectors and bases with
Siemens Fire Safety equipment will be considered a misapplication of Siemens
Fire Safety equipment and as such void all warranties either expressed or implied
with regard to loss, damage, liabilities and/or service problems.
Siemens Building Technologies
Fire Safety
Fire Safety
8 Fernwood Road
Florham Park, NJ 07932
Tel: (973) 593-2600
FAX: (973) 593-6670
Website: www.cerbpyro.com
12/01
5M
SFS-IG
Printed in U.S.A.
Fire Safety
2 Kenview Boulevard
Brampton, Ontario
Canada L6T 5E4
Tel: (905) 799-9937
FAX: (905) 799-9858
December 2001
New Issue