Wireless Bayonet Lampholder

advertisement
Wireless Bayonet Lampholder
(For use with Globalguard systems only)
Installation and Operating Instructions
DECLARATION
POINTS TO NOTE:
Novar ED&S hereby declares that the wireless bayonet lamp holder is in
compliance with the essential requirements and other relevant provisions of
the R&TTE directive (1999/5/EC).
•
Maximum rating of controller: 220-240VAC~50Hz 1000W incandescent or
27W CFL
•
The wall switch cannot be used to turn the lamp ON/OFF. It is only used to
supply power to the controller unit and must be left on to operate correctly
when programmed with your system. The switching of the lamp is managed
by your Globalguard Control Panel (refer to the online software manual for
setup details)
•
If a pendent or lamp shade is fitted in between the lampholder and
controller, then the lamp may be more visible from below the pendant or
lamp shade as shown in below example:
INTRODUCTION
The Wireless bayonet lampholder is only compatible with the Response
Globalguard security system.
It is designed for indoor use only and switches a lamp connected to the holder
ON or OFF to simulate the presence of occupants within the home and deter
potential intruders. The control of the switching is managed by your
Globalguard Control Panel. However pressing a button on the controller will
directly control the device connected.
For further details on setting up the unit to operate as a Programme, Schedule
or Event, please refer to the software manual online.
(www.friedlandproducts.com)
INSTALLATION
1) Ensure the power to the ceiling pendant lampholder is turned off from the
corresponding wall switch
2) Remove the lamp already fitted to the lampholder or allow the lamp to cool
before removing it if it was already left on
3) Fit the ON/OFF controller to the lampholder followed by fitting the lamp to
the controller as shown below
4) Turn on the mains supply from the wall switch. The LED light on the learn
button will slowly flash meaning the lampholder is waiting to be linked to
your Globalguard Control Panel
Ceiling pendent
lamp holder
Lamp may appear below
the pendent or lamp
shade after fitted
MANUALLY OPERATING THE CONTROLLER
You can test to check that the unit turns ON and turns OFF manually after each
time the button below is pressed:
Manual ON/OFF /learn
button with built in LED light
LED light on controller
Controller fits
between pendent
and lamp
Lamp
NEED HELP
Most issues can be solved over the phone.
Call the customer helpline on
0844 736 9149
Monday to Friday 9.00am to 5.00pm
Calls charged at service providers national rate.
LINKING THE CONTROLLER UNIT TO YOUR SYSTEM
1) Ensure that the PC setup software on your PC is loaded
2) Select the +Add Device tab on the home page followed by the Lamp Holder
image as shown below:
Troubleshooting section
Issue
Controller not working
The controller does not work with
my system wirelessly but pressing
the ON/OFF button does activate
the LED
Controller will not link to your
system (Control Panel)
Recommendation
Check mains supply to controller
always turned ON, i.e, the wall
switch is always turned ON
Check that the controller is located
within operating range (30m) and is
linked to your system and setup
correctly to operate under a
Programme, Event or Schedule
Check the lampholder is located
within operating range of the
Control Panel (30m) and the PC
software is placed in learn mode
Specification
Maximum load:
3) Before selecting the Add Now button on the next window displayed, press
and hold the ON/OFF or learn button for 3 seconds until the LED starts flashing
quickly so that the controller is in learn mode
4) Now select the Add Now button on the screen. The learning process may
take approximately 5 seconds and if successfully linked the LED will stop
flashing
5) Another window will be displayed requesting you to enter a Device name
and Location for the lamp module. Enter these to complete setup of the
lampholder
6) Repeat steps 2 to 5 above for any further controllers you may wish to link to
the system
7) For further details on setting up a Programme, Schedule or Event in the PC
setup software to operate the controller(s), please refer to the main software
manual (www.friedlandproducts.com)
8) Should you wish to operate the lamp manually by pressing the learn button
then you will notice the LED will illuminate constantly to indicate on.
CLEARING THE MEMORY OF THE LAMPHOLDER
Should you need to erase your system from the lampholder’s memory, read as
follows:
1)
2)
Press and hold the learn button for 3 seconds until the LED flashes quickly,
then release it
Press and hold the button again for at least 6 seconds until the LED flashes
slowly. This means memory cleared.
Input voltage:
220-240VAC~50Hz 1000W
incandescent or 27W CFL
220-240VAC~50Hz
Operating range
Operating frequency
Protection
30m
433MHz
IP20
Disposal and Recycling (Directive 2002/96/EC)
The product is classified by the Waste Electrical or Electronic Equipment (WEEE) Directive. It should not be disposed of with other household or other commercial
waste. At the end of its useful life the packaging and product should be disposed of via a suitable recycling centre. For information on available facilities, please
contact your local authority or retailer from where the product was purchased.
Guarantee
Novar ED&S undertakes to replace or repair at its discretion goods (excluding non rechargeable batteries) should they become defective within 1 year solely as a
result of faulty materials and workmanship.
Understandably if the product has not been installed, operated or maintained in accordance with the instructions, has not been used appropriately or if any attempt
has been made to rectify, dismantle or alter the product in any way the guarantee will be invalidated.
The guarantee states Novar ED&S entire liability. It does not extent to cover consequential loss or damage or installation costs arising from the defective product.
This guarantee does not in any way affect the statutory or other rights of a consumer and applies to products installed within UK and Eire only.
If an item develops a fault, the product must be returned to the point of sale with :
1.
2.
3.
Proof of purchase.
A full description of the fault.
All relevant batteries (disconnected).
CUSTOMER HELPLINE
0844 736 9149
Most issues can be solved over the phone in a few minutes. Please contact our Helpline Team on
the above number for any installation and general advice regarding our products
Lines open 9.00am to 5.00pm, Monday to Friday. Calls are charged at service providers national
rate.
Novar Electrical Devices and Systems Limited (A Honeywell company)
The Arnold Centre, Paycocke Road, Basildon, Essex SS14 3EA. UK
www.friedlandproducts.com
© Novar Electrical Devices and Systems Limited. 2012
50072727-001 Rev.A
Download