INSTALLATION AND OPERATION MANUAL
CE-(X)UTP
Ethernet-over-UTP/Twisted Pair
Extender with Pass-Through PoE
Important Safety Warning:
Read and keep these directions
The CE-(X)UTP Ethernet over UTP line consists of four models that support 100 Mbps
Ethernet as well as pass-through Power over Ethernet (PoE) over twisted pair cable
Heed all warnings
(CAT5, UTP). These models support transmission distances of up to 3,000 feet (914 m)
Follow all instructions
at 10 Mbps, or 2,100 feet (640 m) at 100 Mbps. The CE-1UTP, the CE-4UTP, CE-8UTP
Do not use this apparatus near water
and the CE-16UTP transport, one, four, eight or sixteen channels respectively. The
Clean only with a dry cloth
IEEE 802.3-compliant Ethernet electrical interface of these Ethernet extenders also
Install in accordance with the
manufacturer’s instructions
meets the requirements for IEEE 802.3af/at PoE power, passing-through up to 30 watts
This installation should be made by a
qualified service person and should conform
to all local codes
See further safety instructions on page 8
of power per port to the powered device (PD). The CE-(X)UTP series may also be used
interchangeably with other Ethernet-over-UTP extenders.
Environmentally hardened to the requirements of NEMA TS-1/TS-2 for most out-of-plant
applications, and true plug-and-play design ensures ease of installation and operation.
LED indicators are provided for rapidly ascertaining the operating status of the device.
See Figures 7 – 9 on page 6 for LED explanations.
Packaged in a rugged aluminum housing, these units are designed for desktop or standalone mounting. The CE-8UTP and CE-16UTP are offered in EIA 19” 1U high rack for easy
installation. See Figures A through C on page 7 for mounting instructions.
See Figures 1 – 8 for complete installation details.
Vicon part number 8009-8242-00-00 Rev 0112
Page 1
INSTALLATION AND OPERATION MANUAL
CE-(X)UTP
FIGURE 1 – CE-1UTP
CAT5/6
UTP
CAT5/6
BLACK
BLACK WITH
WHITE STRIPE
FIGURE 2 – CE-1UTP
LEFT PANEL
RIGHT PANEL
FIGURE 3 – CE-4UTP
LEFT PANEL
CAT5/6 or UTP
CAT5/6
Tech Support: 800.34.VICON (800.348.4266)
Vicon part number 8009-8242-00-00 Rev 0112
Page 2
INSTALLATION AND OPERATION MANUAL
CE-(X)UTP
FIGURE 4 – CE-8UTP
12V Power Supply
CAT5/6 or UTP
CAT5/6 or UTP
CAT5/6
CAT5/6
Ground Screw
FIGURE 5 – CE-16UTP
12V Power Supply
CAT5/6 or UTP
CAT5/6 or UTP
CAT5/6 or UTP
CAT5/6 or UTP
CAT5/6
CAT5/6
CAT5/6
CAT5/6
Ground Screw
Tech Support: 800.34.VICON (800.348.4266)
Vicon part number 8009-8242-00-00 Rev 0112
Page 3
INSTALLATION AND OPERATION MANUAL
CE-(X)UTP
FIGURE 6 – POSSIBLE ETHERNET CONFIGURATIONS
Multiple configurations are possible. Consult you VIcon Sales Engineer.
Single Port CopperLine over UTP
NVR
CE-1UTP
PoE Switch
≤3,000 ft
(914 m) Cat-5
CE-1UTP
≤328 ft
(100 m) Cat-5
CE-1UTP
≤328 ft
(100 m) Cat-5
PoE Camera
Multi Port over UTP
≤3,000 ft
(914 m) Cat-5
CE-16UTP
PoE Camera
PoE Switch
NVR
4-Port Switch Extended over UTP or Coax
≤3,000 ft (914 m) Cat-5
OR
≤5,000 ft (1524 m) Coax
CE-16UTP
CE-16UTP
IP Cameras
CE-4US1TPC
≤328 ft
(100 m) Cat-5
IP Cameras
PoE Switch
NVR
Managed High Power Midspan
NVR
CE-1UTP
≤3,000 ft (914 m)
Cat-5
CE-1UTP
≤5,000 ft (1524 m)
Coax
Switch
CE-16IPS
Tech Support: 800.34.VICON (800.348.4266)
CE-1UTP
CE-1UTP
Data +
Power
Data
+Power
PoE Camera
PoE Camera
Vicon part number 8009-8242-00-00 Rev 0112
Page 4
INSTALLATION AND OPERATION MANUAL
IP Camera-end
Installation (CE-1UTP)
Off
S1 S2 S3
On
Ethernet Switch/NVR-end
Installation
Set the S1 10/100BaseT DIP switch
to the appropriate rate based on the
required maximum data rate and
maximum distance.
OFF = 10BaseT; ON = 100BaseT
Set the S2 Master/Slave DIP switch to ON for “Master” mode
CE-(X)UTP
S1 S2 S3
Off
CE-1UTP
On
Set the S2 Master/Slave DIP switch to OFF
for “Slave” mode
Set the S1 and S3 DIP switches to match the setting on the
camera-end.
Set the S3 1- or 4-pair DIP switch ON for 1-pair or OFF for
4-pair operation.
For systems not utilizing PoE, connect the 12V power supply
to the power connector of the CE-1UTP. A power adapter
connector is provided to simplify connection.
Connect the IP camera RJ-45 connector to the 10/100BaseT
Ethernet port of the CE-1UTP using a standard Cat5/6 cable,
100m length (max).
1-p
4-P
S1 S2 S3 S4
10
100
S1 S2 S3 S4
CE-4UTP, CE-8UTP
and CE-16UTP:
For each channel used, set the
appropriate dip switches for each
channel to match the camera end.
ote: Multichannel units are preset to
N
“Slave” mode. No adjustment required.
Connect one end of the long UTP cable to the RJ-45 connector
of the CE-1UTP.
For systems not utilizing PoE, connect
the 12V power supply to the power connector of the selected
CE-(X)UTP.
The link LED on the 10/100 connector should be “ON” to
indicate propre connection between the camera and the CE1UTP.
Connect the RJ-45 connector of the Ethernet switch to the
10/100BaseT Ethernet port of the selected
CE-(X)UTP using a standard Cat5/6 cable, 100 m length (max).
Connect one end of the long UTP cable to the RJ-45 connector
of the selected CE-(X)UTP.
The Link LED on the 10/100 Ethernet connector should be
“ON” to indicate proper connection between the switch and
the selected CE-(X)UTP.
The Link LED (Red for 100BaseT, Green for 10BaseT) will
be “ON” and not flashing to indicate confirmed connection
between the CE-1UTP and selected
CE-(X)UTP extenders.
Tech Support: 800.34.VICON (800.348.4266)
Vicon part number 8009-8242-00-00 Rev 0112
Page 5
INSTALLATION AND OPERATION MANUAL
CE-(X)UTP
FIGURE 7 – POWER LED INDICATORS
POWER
RED
Power is on
OFF
Power is off
FIGURE 8 – EXTENDED LED INDICATORS
TRAFFIC (Extended)
10/100BaseT
GREEN
–
Connection is OK,
10BaseT mode
YELLOW
Flashing, Traffic present –
RED
–
Connection is OK,
100BaseT mode
OFF
No traffic
–
FIGURE 9 – ETHERNET LED INDICATORS
TRAFFIC (Standard) Link
GREEN
Flashing – Connection
is OK with traffic
–
YELLOW
–
Connection is OK
OFF
No connection
No connection
Tech Support: 800.34.VICON (800.348.4266)
Vicon part number 8009-8242-00-00 Rev 0112
Page 6
MECHANICAL INSTALLATION INSTRUCTIONS
CE-(X)UTP
Installation Considerations
The CE-1UTP and CE-4UTP are supplied as standalone modules.
The CE-8UTP and CE-16UTP can be installed as standalone
modules or can be rack-mounted with the addition of the provided
19-inch rack-mounting ear brackets.
Figure A
Dimensions are for the CE-1UTP standalone module.
1.15" (30 mm)
1.6" (40 mm)
1.6” (40 mm
3.73" (95 mm)
Figure B
Dimensions are for the CE-4UTP standalone module.
1.6” (40 mm
3.3"
(84 mm)
3.6" (92 mm)
Figure C
Dimensions are for the CE-8UTP and CE-16UTP modules.
3.25"
(82.5 mm)
17" (432 mm)
1.75"
(44.5 mm)
Tech Support: 800.34.VICON (800.348.4266)
Vicon part number 8009-8242-00-00 Rev 0112
Page 7
MECHANICAL INSTALLATION INSTRUCTIONS
• Read and keep these directions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Install in accordance with the manufacturer’s instructions.
•T
his installation should be made by a qualified service person
and should conform to all local codes.
•D
O NOT bundle UTP or Coax signals in the same conduit as
high-voltage wiring.
•T
o reduce the risk of fire or electrical shock, do not expose these
products to rain, moisture, dripping or splashing.
•N
o objects filled with liquids, such as vases, shall be placed on
the equipment.
•D
O NOT install the unit in a place where the operating ambient
temperature exceeds 75ºC.
•M
ake sure that the external power supply output voltage is in the
recommended range.
•D
o not install near any heat sources such as radiators, heat
registers, stoves or other apparatus (including DVRs) that
produce heat.
•P
rotect the power cord from being walked on or pinched,
particularly at the power source, convenience receptacles and
the point where they exit from the apparatus.
WARNING: T
o reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture. This
apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
WARNING: T
his apparatus is a Class I product. This product
must be connected to a mains socket outlet through
an AC to DC power supply.
WARNING: T
he mains plug is used as the disconnect device and
shall remain readily operable.
WARNING: F
or non-PoE applications, unit is to be connected to
a mains socket outlet through a Listed Class I power
supply rated 12 VDC or 24 VAC.
• Only use attachments/accessories specified by the manufacturer.
•U
nplug this apparatus during lightning storms or when unused
for long periods of time.
•R
efer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as when a power supply cord or plug is damaged, liquid
has been spilled, objects have fallen inside the apparatus, the
apparatus has been exposed to rain or moisture, do not operate
normally or has been dropped.
•T
he main plus is used as the disconnect device and shall remain
readily operable.
89 ARKAY Drive | HAUPPAUGE, NY 11788 | USA
T: 631.952.2288 | F: 631.951.2288 | toll free: 800.645.9116
web: www.vicon-security.com
uk: +44 (0)1489 566300
© 2011 Vicon Industries Inc. All Rights Reserved. Vicon and its logo are registered trademarks of Vicon Industries Inc.
Vicon part number 8009-8242-00-00 Rev 0112
Page 8