Type
Job. Ref.
Catalog Number
r PMHZ-PAR-7100
r PMHZ-PAR-770
7" APERTURE
HIGH INTENSITY DISCHARGE
METAL HALIDE/CERAMIC METAL HALIDE
RECESSED DOWNLIGHT
70-100 WATT PAR 38
The 70-100 watt metal halide lamp source offers one of the most efficient
lumen/watt fixture packages in recessed downlights. The specifically designed
reflector ensures the proper cut-off (greater than 45 degrees) while at the same
time producing optimum lumen output with low glare. The one piece design
reflector eliminates light leaks around the reflector edge. The reflector is designed
specifically for a metal halide lamp, thereby, creating optimum performance in a
lamp reflector combination.
APPLICATION
These wet location rated fixtures have been ETL listed and tested to UL standard
#1598. The fixture is suitable for use either indoor or outdoor in a canopy, soffit, or
an overhang area. This fixture is best suited when used in a medium ceiling
application.
Trims
r -B Black Baffle
PRODUCT SPECIFICATION DATA:
•
•
•
•
•
•
•
•
•
•
•
•
•
Precision formed 20 ga. galvanized steel plaster pan
Designed for lamps mounted vertical
14 ga. galvanized 28 Cu. In. J box w/covers
Tested to UL Standard #1598/CSA C22.2 #250.0-00
Suitable for through wiring 4 in/4 out #12 AWG
Positive retaining clips for trim
Capable of ceiling thickness adjustment up to 2"
120/277V HPF magnetic ballast is standard. Electronic ballast
recommended for ceramic metal halide lamp
Suitable for use in wet locations, "for covered installations only"
Bar hangers accommodate 27" span
Vertical bar hangers mount on all sides
Reflector ceiling trim flange is painted white as standard
Not for use in direct contact with insulation
r -WB White Baffle
r -PRC Clear Multiplier Cone
r -PRB Black Multiplier Cone
r -PRC-G Gold Multiplier Cone
r -POR Open Trim for Par Lamp
Alzak® is a registered trademark of Alcoa Aluminum
Options and Modifications
r Cat. No. -F Fused
r Cat. No. -QRS Quartz Restrike
r Cat. No. -EB Electronic Ballast
r Cat. No. _____________________________
r Cat. No. _____________________________
r Cat. No. _______________________________
r Cat. No. _______________________________
r Cat. No. _______________________________
r Cat. No. _______________________________
r Cat. No. _______________________________
·
CONE OF LIGHT
PMHZ-7100-B
Distance to
Illuminated
Plane
Initial Nadir
Footcandles
Beam
Diameter
12'
142
5.0
14'
96
6.0
16'
70
7.0
18'
53
8.0
20'
40
9.0
COEFFICIENT OF
UTILIZATION
CANDLEPOWER DISTRIBUTION CURVE
Test No:
Lamp:
Lumens:
LPW@ 120V:
S/MH:
Efficency:
P379816
MP100 PAR 38
5,500
32 LPW
0.6
72%
75°
60°
45°
Energy Data
Input Watts:
125
Pwr. Factor (Max.): 90%
Line Current: 120 / 2.40
277 / 1.05
12000
0°
15°
·
30°
rc
rw
RCR 0
1
2
3
4
5
6
7
8
9
10
80%
50 30
50%
50 10
83
80
78
76
74
73
71
69
68
66
79
77
76
74
72
71
70
68
67
66
82
79
76
74
71
70
68
67
66
64
78
76
74
72
70
69
68
66
65
64
Tested to current IES and NEMA standards under stabilized laboratory conditions. Various operating factors can cause differences between laboratory data and actual field measurements.
(Continued on Reverse Side) PAGE C 264
7230 Industrial Blvd. - Covington, GA 30014 • 770-787-8490 • FAX: 770-787-8521
© 2007
Catalog Number
7" APERTURE
HIGH INTENSITY DISCHARGE
METAL HALIDE/CERAMIC METAL HALIDE
RECESSED DOWNLIGHT
70-100 WATT PAR 38
REFLECTOR
1.This Alzak® treated reflector is available in clear as
standard. Produced of .050 aluminum eliminates reflector
deflection. The precise spinning produces a one piece
reflector and trim ring. The parabolic design is polished to
maximize the reflectance. The positive "grippers", mounted
on the reflector, allow the reflector to be secured snug to
the ceiling without the possibility of slipping. When lens are
used reflectors are eliminated.
r PMHZ-PAR-7100
r PMHZ-PAR-770
MOUNTING BRACKETS
5. The mounting bracket is engineered to be used in either
a T Bar, sheetrock, or plaster ceiling. The bar hangers are
secured to the plaster frame and may be extended to 27".
Bar hangers have provisions for mounting direct to
structural roof members (supplied by others).
JUNCTION BOX
6. Tested and listed for eight # 12 AWG (4 in & 4 out) 90°C
conductors, feed through branch wiring, 1/2" and 3/4" pry
outs and a galvanized finish. Positioned to allow straight
conduit runs. Access to the junction box in an inaccessible
ceiling is accomplished through the reflector opening.
TRIM RING
2. The trim ring is painted white as the standard color. The
trim ring has a small return which makes the trim ring
appear to flow into the ceiling material.
SOCKET HOUSING
3. The UL listed socket has a positive attachment inside the
cavernous lamp chamber. The air flow is more than
adequate for cooling of the lamp and socket lamp
connection.
BALLAST
7. Ballast are thermally protected and potted for maximum
protection and sound deadening quality. Ballast are
magnetic with dual taps for 120 or 277V wiring.
SOCKET
8. The socket is made from porcelain with a nickel plated
screw shell. The standard is a medium base open rated 4KV
pulse rated device. The socket is positively attached to
socket housing using screws in lieu of springs.
HOUSING MOUNTING FRAME
4. A one piece 20 Ga. galvanized steel mounting frame
allows for rigid support of the complete fixture without
sagging. The frame is designed with a 1/2" collar which
extends from the bottom to accommodate ceiling materials
while finishing flush with the ceiling. There is an additional
1 1/2" inches of adjustment for abnormal ceiling thickness.
LABELS
All fixtures are tested to the appropriate UL Standards by
Electrical Testing Laboratory and conform to CSA
C22.2#250.0-00. The labels are affixed to the fixture
indicating the test number and the standards used.
6 JUNCTION BOX
8 SOCKET
3 SOCKET HOUSING
7 BALLAST
7.75
REFLECTOR 1
8.75
(50-100W) 14.50
6.50
6.75
TRIM RING 2
7.50
4 HOUSING/MOUNTING 5 MOUNTING BRACKET
14.75
Dimensions and specifications in this catalog are based on the most current available data and are subject to change.
PAGE C 264 (Continued from Front Side)
7230 Industrial Blvd. - Covington, GA 30014 • 770-787-8490 • FAX: 770-787-8521
© 2007