1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
© 2011 Edge Lighting. All Rights Reserved.
SATIN-_F1_-SN-_
904-SATIN-F1-02
Installation Instructions for Compact Florescent Satin Ceiling 12, 15, & 18
- This product is ETL listed for indoor dry locations.
- This product is ceiling mounted only.
- This product can mount to either a 4" square electrical box
with round plaster ring or an octagon electrical box.
- This instruction shows a typical installation.
- This product is not dimmable.
SAVE THESE INSTRUCTIONS!
Disassemble the Fixture
A
BACKPLATE
1: Remove the three thumb nuts from the threaded studs and
detach the backplate from the fixture housing.
Wiring for Standard Installation
B
THREADED
STUD
1
THUMB
NUT
ELECTRICAL
BOX
1
1
FIXTURE HOUSING
1
BACKPLATE
2
2
1: Feed the power wires through the backplate center hole.
2: Mount the backplate to the electrical box with the provided
two #8-32 screws.
C
BACKPLATE
FIXTURE
HOUSING
3: Make sure that the fixture is grounded in accordance with
local electrical codes.
4: Connect the white fixture wire to the neutral power wire with
a wire nut.
3
5
#8-32
SCREW
4
5: Connect the black fixture wire to the hot power wire with a
wire nut.
6: Follow the "Finish Installation" steps on page 3 to complete
the installation.
1
Always on Emergency Light Wiring (F1E Version Only)
D
CEILING
ELECTRICAL
BOX
BACKPLATE
QUICK
DIS-CONNECT
CONNECTOR
THREADED
STUD
4
NOTE: Skip this step if installing standard Fluorescent version.
NOTE: Follow this step if light will always be on, and in case of
power failure the battery backup will turn the fixture on.
1: Follow wiring diagram in Drawing D to properly install fixture.
BATTERY
2: Connect the hot power wire to the battery & ballast black
wires with a wire nut.
3: Connect the neutral power wire to the battery & ballast white
wires with a wire nut.
2
4: Connect the quick dis-connect connector together.
3
NOTE: The battery needs to be charged for at least 2 hours.
Perform test after battery is properly charged.
BALLAST
PRE-CONNECTED
WIRES NOT SHOWN TO
AVOID CONFUSION
BATTERY
1
5: Refer to "Finish Installation" steps on page 3 to complete the
installation.
Switch Controlled Emergency
Light Wiring (F1E Version Only)
E
L
N
(BLK)
(WH)
SWITCH
BALLAST
ELECTRICAL
BOX
NOTE: Skip this step if installing standard Fluorescent version.
NOTE: Follow this step if light will have an on/of switch, and in
case of power failure the battery backup will turn on.
BACKPLATE
THREADED
STUD
5
QUICK
DIS-CONNECT
CONNECTOR
BATTERY
NOTE: Two power lines are needed to wire the fixture for this
version.
1: Follow wiring diagram in Drawing E to properly install fixture.
4
3
2: Connect the white ballast & battery wires to neutral power
wire with a wire nut.
2
BALLAST
3: Connect the hot power wire coming from the switch to the
black wires of the ballast with a nut.
4: Connect the other hot power wire to the black wire of the
battery with a wire nut.
PRE-CONNECTED
WIRES NOT SHOWN
(BLK)
TO AVOID CONFUSION
5: Connect the quick dis-connect connector together.
L1
NOTE: The battery needs to be charged for at least 2 hours.
Perform test after battery is properly charged.
(RED)
(BLK)
L2
BALLEST
SWITCH
6: Refer to "Finish Installation" steps on page 3 to complete the
installation.
BATTERY
1
N
(WH)
2
Finish Installation
F
ELECTRICAL
BOX
CEILING
BACKPLATE
THREADED
STUD
1
2
2
1: Place all wire and wire nut connections inside backplate.
2: Align and push the fixture housing onto threaded studs and
tighten the three thumb nuts completely to secure the fixture
housing in place.
2
2
THUMB NUT
G
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
SOCKET SLOT
NOTE: The 12" Satin Ceiling uses only one 22 Watt lamp.
3
Use MAX 22 Watt Type Circline 4-pin T5 2GX13
Base Fluorescent Lamp for 12", 15" and 18"
Satin Ceilings.
LAMP PIN
Use MAX 40 Watt Type Circline 4-pin T5 2GX13
Base Fluorescent Lamp for 15" and 18" Satin Ceilings.
3: Starting with the inner lamp, insert the lamp pins into the
socket slots and secure it in place snapping into the spring
clip(s). Repeat this step for outer lamp (15" and 18" only).
H
4: Insert the three posts of the shade into the fixture housing
slots and turn the shade clockwise to lock into place.
4
4
FIXTURE
HOUSING
SLOT
NOTE: To re-lamp the fixture, carefully rotate the glass shade
counter clockwise and remove the shade. Carefully pull the old
lamp(s) out of the socket slot and the spring clip(s). Follow steps 3
to 5 to re-install the lamps and shade.
SHADE POST
3