Installation/Operating Instructions
Baronet/HW 110V and 220V Electric Projection Screen by Draper
These Installation/Operating Instructions are available in the official language
of the country where you purchase the product. Please contact your
distributor to request a copy.
Vous pourriez demander les instructions d’installation et d’opération traduises
dans la langue officielle du pays ou vous achetez le produit. Veuillez
demander à votre distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der
offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben,
vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.
Caution
 Read instructions through completely before proceeding.
 Follow instructions carefully. Installation contrary to instructions invalidates warranty.
 Screen should be accessible for complete removal should fabric become damaged or should other service be required.
 Screen should be installed level (using a carpenter’s level).
 Nothing should be fastened to screen dowel or viewing surface.
 Operating switch(es) packed separately in screen carton. Do not discard with packing material.
 Screen operates on 110-120V AC, 60 Hz. or 220V AC, 50 Hz. or 60 Hz.
current, depending on model ordered.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Wall Installation:
Mount screen through holes in back of endcaps as shown. Installer should
furnish appropriate hardware as required.
Recessed Installation:
Recess should permit access for removal of screen if necessary. Screen may
be mounted as in suspended or wall installation. Angles may be used (provided by others).
Electrical Connections
Screen operates on 110-120V AC, 60 Hz./220V AC, 50 Hz. or 60 Hz. current,
depending on model ordered. Duty Cycle: On 26 seconds/off 3 minutes.
Junction box is located inside left endcap and cover plate is secured to
endcap with two screws. Junction box contains pigtail leads and grounding
screws, per wiring diagram on reverse.
Screen is shipped with internal wiring complete and control switch(es) fully
boxed. Wire connecting screen to switch(es) and switch(es) to power supply
should be furnished by installer. Connections should be made in accordance
with attached wiring diagram, and wiring should comply with National and
local electrical codes.
All operating switches should be “off” before power is connected. Do NOT wire
motors in parallel.
Operation
Before operating screen, remove small foam pieces which keep dowel in case
during shipping.
Hanging Screen
General:
When locating viewing surface and checking clearance for screen’s operation, remember surface is centered in case. Handle case carefully to protect
its finish.
Regardless of mounting method, screen should be positively and securely
supported so that vibration or even abusive pulling on the viewing surface will
not cause case to work loose or fall. Installer must insure that fasteners used
are of adequate strength and suitable for mounting surface chosen.
Suspended Installation:
Suspend screens from holes in top of endcaps as shown. "S" hooks, chains
(or cable) and turnbuckles should be provided by installer. “S” hooks should
go through the front holes on the endcaps (see drawing below), and both
ends of the “S” hooks should be crimped for additional safety. Chains should
be attached to beams or other structural members. Turnbuckles should be
adjusted so screen hangs level.
Front
Back hole for wall mounting.
Hardware by others.
Crimp
Crimp
Mounting angle
and hardware
by others.
Suggested for
recessed
installations.
Adjustments
Minimum 5 cm wide
slot for passage of
viewing surface if
suspended above ceiling
Copyright © 2015 Draper Inc.
Top Hole for
suspended mounting.
Hardware by others.
Rear
Screen is equipped with a 3-position operating switch, located on the power cord.
To lower the screen, move switch down. Screen will stop automatically when lower
limit switch is reached. To raise the screen, move switch up. Again, the screen
will stop automatically when the upper limit switch is reached. The screen may
be stopped in any intermediate position by moving the switch to the center “off”
position during operation.110-120V/220V Single Station Control — 3-position
up-off-down switch permits operation to be stopped at any point. Factory adjusted
limit switches automatically stop screen when fully down or fully up. 220V version
is CE certified.
110-120V/220V Multiple Station Control—Switches are similar in appearance
to 110V/220V Single Station Control. Screen stops when switch is released and
may be restarted in either direction. Factory adjusted limit switches stop screen
automatically when fully up or fully down.
24V Control — Three-button up-stop-down switches stop at any point desired,
operate in any sequence. Factory adjusted limit switches automatically stop
screen when fully up or fully down.
Key Operated Switching — Two kinds of key-operated switches are optionally
available with this unit. 1 The key-operated power supply switch controls power to
the screen and switches. When it is “off ”, the switches will not operate screen. Key
may be removed from the switch in either “on” or “off” position. 2 A three-position
key switch permits the screen to be operated directly by key. In this case, the
screen’s operator must always have a key.
RS232/Ethernet—Serial communication and network communication optionally
available with wall switches, RF or IR remote.
Form BaronetHW_Inst15
Example of
suspension
above ceiling.
Ceiling tile
and grid
(by others)
Printed in U.S.A.
Please Note: Screen limits are factory set for optimum performance of the
screen. Any adjustment of these limits could void the warranty. Please
check with Draper prior to resetting screen limits.
CAUTION: Always be prepared to shut screen off manually when new
adjustment is being tested. Screen may be severely damaged if viewing
surface is allowed to run too far up or too far down.
CAUTION: Be sure all switches are in “off” position before adjusting limit
switches.
“Down” limit switch: Down stopping position can be adjusted by turning white
knob with a screw driver or hex wrench. Turning knob counterclockwise will allow
viewing surface to run farther down. Turning it clockwise will reduce the amount of
exposed viewing surface.
“Up” limit switch: Up stopping position can be adjusted by turning red knob
with a screw driver or hex wrench through the small grommet. Turning knob
counterclockwise will allow surface to run farther into screen case. Turning it
clockwise will allow viewing surface to stop farther out of screen case.
Baronet/HW 110-120V
Baronet/HW220V AC
AC version is certified by
version is CE certified.
Underwriters’ Laboratories, Inc.,
for the U.S. and Canada.
If you encounter any difficulties installing or servicing your Baronet/HW screen, call your
dealer or contact Draper, Inc., Spiceland, Indiana, +1 765-987-7999 or fax +1 765-987-1689.
Baronet/HW by Draper
Page 2 of 2
Case Dimensions
3¼"
(83 mm)
Fabric width + 5¾" (146 mm)
3¼"
(83 mm)
3¾"
96 mm
Viewing
Surface
Wiring Diagrams
Baronet/HW 110V AC
Baronet/HW 220V AC (CE)
Multiple Station Control
Junction box at
left end of screen
Single Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Motor Ground)
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Motor Ground)
Blue
Black
Control
switch
Single gang box by others
Min. 4" x 2-1/8" x 1-7/8" deep.
3 shown. More or less equally
feasible.
Black
220v, PE
50 Hz.
Low Voltage (& Wireless) Control Wiring Diagram
CE Approved
Low Voltage
Control Module
Black
Red
White
Receiver
Button
Location of key
operated 0n-off
switch if furnished.
White-110v or Blue-220v (Common)
Black-110v or Brown-220v (Down)
Red-110v or Black-220v (Up)
3 Button Wall Switch
Green/Yellow
YellowDOWN - Black
Chassis ground label
GreenCOM - White
+
Zinc plated chassis ground screw
UP - Red
All-Pole Disconnect
Hot
Black
by Others
Optional infrared
receiver package
Optional
radio receiver
package
Electrically Straight
Data Cable to 220v,
more50 Hz.
LVC-IV modules*
RS232/485 Inputs/Outputs
Wall Switch
Low Voltage Trigger
3-28 VAC
*A maximum of six (6)
IR Eye Input
LVC-IV modules can be
linked together.
Dashed wiring by electrician
Low voltage wiring by others
110-120V 3-Position Wall Switch
Internal Screen Wiring
White
Brown
Red
Black (Dn)
Red (Up)
White (Com)
Dashed wiring
by installer
Junction box at
left end of screen
Neutral
Control
switches
24 VDC
White or Blue-Common to screen & 110/220V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110/220V AC-Hot
Black-to 110/220V AC-Hot
Green/Yellow (Ground)
220V 3-Position, Surface Mount Wall Switch
3.8 mm (1 1/2")
7 mm (2 3/4")
4.5 mm
UP
Dashed wiring
by installer
220v, 50 Hz.
Location of key
operated on-off
switch if furnished
Black (Dn)
Red (Up)
White (Com)
N
Blue
Red
Hot
Dashed wiring
by installer
Low Voltage, IR Remote or RF Remote (LVC-IV)
To
110-120 VAC L1
Line
GND
Blue
Black
Neutral
Black
Blue
Red
Blue
To 110V AC Line
Internal Screen Wiring
White (Common)
Red (Up)
Black 110 (Down)
Green/Yellow
(Motor Ground)
Green/Yellow
Chassis ground label
Zinc plated chassis ground screw
Red
Black
Red
Please Note: Do not wire motors
in parallel.
+
Cap off with wire
nut and tape
Blue
Red
To 110V AC Line
Green/Yellow
Chassis ground label
Zinc plated chassis
ground screw
Dashed wiring
by electrician
Black
Location of key
operated on-off
switch if furnished
Not CE Approved
Cap off with wire
nut & tape
Red
Dashed wiring
by electrician
Multiple Station Control
Internal Screen Wiring
White-110v or Blue-220v (Common)
Black-110v or Brown-220v (Down)
Red-110v or Black-220v (Up)
Internal Screen Wiring
White-110v or Blue-220v (Common)
Black-110v or Brown-220v (Down)
Red-110v or Black-220v (Up)
+
Control
switch Single gang box by others
Min. 4" x 2-1/8" x 1-7/8" deep
Blue
Red
Black
Junction box at
left end of screen
CE Approved
Junction box at
left end of screen
Neutral
Junction box at
left end of screen
L1
Single Station Control
(1 3/4")
3.2 mm (1 1/4")
3"-6" leads
11.8 mm
(4 1/2")
8.6 mm
(3 3/8")
DOWN
www.draperinc.com
(765) 987-7999
7.8 mm
(3 1/16")