Measure & Analyze – MCP
P. 1 ... 2
Type 5110
5110 VibraPOWER ™ MULTIMETER COMPATIBLE COUPLER
Turn a digital multimeter into a hand-held vibration measurement
system or verify sensor and cable integrity with this portable, low
cost, battery-operated coupler. The Kistler type 5110 provides a
simple approach to making sensor measurements directly, using
the functions found on today’s digital multimeters or scope meters
(i.e., AC RMS, frequency, DC bias, peak hold, PC interface, etc.).
The VibraPOWER coupler supplies constant current excitation for
low impedance, voltage mode piezoelectric sensors. Direct plug-in
to most common multimeters is provided by banana type connectors on the back of the case. An AC coupled BNC type output
Continued
•
•
•
•
•
•
Makes a multimeter into a sensor readout device
Interfaces with Piezotron® or voltage mode piezoelectric sensors
Provides constant current excitation from 9V battery
Low battery indicator
Economically priced
Conforming to CE
000-329e-11.00 (DBK12.5110e-11.00)
Technical Data
Unit
Sensor Input
Excitation Current (±10%)
mA
No Load Voltage
VDC
Sensor Output
Voltage swing
Vpp
Voltage gain
Noise
µVrms
Output to BNC Connector
Impedance
Ω
Frequency Response (±5%)*
10Vpp
Hz
5 Vpp
Hz
1 Vpp
Hz
Time Constant (±10%)
s
Output to Multimeter
Frequency Response (±5%)*
10 Vpp
Hz
5 Vpp
Hz
1 Vpp
Hz
Power
Internal battery
type
1 ea., type IEC 6LR61
Battery Life
hr
(typ., 25 °C, continuous, 2mA to sensor)
Connectors
Sensor Input and Signal Output
type
Multimeter
type
Temperature Range Operating
°F
°C
Storage
°F
°C
IP rating
Weight (battery included)
g
5110
2
≥20
≥18
1
100
<100 in series with 47 µF
0.07 ... 30 000
0.07 ... 60 000
0.07 ... 300 000
10
Typical system shown; digital multimeter, connecting
cable and accelerometer are not supplied.
DC ... 30 000
DC ... 60 000
DC ... 300 000
9V alkaline
≥45
BNC neg.
banana
14 ... 130
–10 ... 54
– 4 ... 140
–20 ... 60
40
150
* 1 MΩ load; 3 meters total cable length. Actual frequency response is dependent
upon cable length and signal amplitude.
1 g = 9.80665 m/s 2, 1 inch = 25.4 mm, 1 gram = 0.03527 oz
Kistler Instrument Corporation reserves the right to discontinue or change specifications, designs or materials
without notice consistent with sound engineering principles and quality practices.
Kistler Instrument Corporation, 75 John Glenn Drive, Amherst NY 14228
Phone 716-691-5100, Fax 716-691-5226, e-mail: kicsales@kistler.com, www.kistler.com
P. 2
connection is also provided on the side panel for interface to other
measurement devices. The coupler, a multimeter/scope-meter, and
a voltage mode piezoelectric sensor provide a hand-held system
ideally suited for roving vibration monitoring in a machinery maintenance environment.
Dimensions in inches [mm]
3.8 [96.5]
The coupler extends the measurement capability of the multimeter,
while it’s small size retains the convenience of hand-held operation.
Low cost of the unit makes it ideal as an addition to your tool box
for troubleshooting sensors, cable or vibration problems in an
industrial environment.
Battery Low
Indicator
< Sensor
ON
2.40 [61.0]
OFF
> Output
Supplied Accessory
300-0092-002
Mulitimeter Coupler
Type 5110
9V alkaline battery
Optional Accessory
5110S1
kit includes 5110, carrying case, mounting wax and
9V battery
1.76
[44.7]
000-329e-11.00 (DBK12.5110e-11.00)
1.01 [25.4]
Kistler Instrument AG Winterthur, Postfach 304, CH-8408 Winterthur
Tel + 41 - 052 - 224 11 11, Fax + 41 - 052 - 224 14 14, sales@kistler.ch, www.kistler.com
Kistler Instrument Corporation, 75 John Glenn Drive, Amherst NY 14228
Phone 716-691-5100, Fax 716-691-5226, e-mail: kicsales@kistler.com, www.kistler.com