PROJECT INFORMATION
SHERIFF™
Job Name
Fixture Type
SH5 SERIES WITH OCCUPANCY SENSOR
Catalog Number
Approved by
PRODUCT FEATURES:
»»Surface mount – ceiling or wall; 5"×24"
»»ADA Compliant
»» 16-gauge cold rolled steel baseplate with seam
welded end caps
»» P12 polycarbonate wraparound lens
»» Peace of Mind Guarantee® against breakage
SPECIFICATIONS
BASEPLATE: One-piece 16-gauge CRS baseplate with welded corners. Baseplate provided with four-point mounting holes and one wireway hole – see Cross Section/Details. TGIC polyester powder
coat – 5-stage pre-treatment. Salt spray test: 1,000 hours; Reflectance: 92%. Lens is positioned in baseplate channels and retained with (2) stainless steel Torx® with center pin fasteners. Baseplate/
end caps mount flush to ceiling or wall surface.
LENS: Cold formed .156" P12 polycarbonate lens. See Options for alternate lenses.
SOCKETS: Shock-resistant sockets with internal locking collar to ensure positive lamp retention.
HARDWARE: Stainless steel Torx® with center pin fasteners secure lens in baseplate channel.
ELECTRICAL: Class P ballast. Fluorescent electronic dual voltage ballast with high power factor. One-lamp 90 minute nickel-cadmium battery pack (EL) includes inverter charger, test switch and
charging indicator lamp.
SUPER HIGH FREQUENCY OCCUPANCY SENSOR: Controls line voltage to operate luminaire. Detects motion via electromagnetic waves, so it can be used behind luminiare lenses. 120/277 VAC
operation. 20 foot radius of operation. Time delay from 30s-30m. Sensitivity adjustable.
INSTALLATION: Four-point mounting required for Peace of Mind Guarantee®.
LISTINGS: UL and CUL listed for Wet Location – covered ceilings only. UL and CUL listed for Damp Locations – wall mount. ADA compliant.
ADA
ORDERING INFORMATION (Ex: SH524MS-2-17-RS-1-120-FS)
Model
SH524MS
Lamp Qty
Lamp Type
Ballast Type
Circuit Qty
2
Voltage
Options
Accessory
1
Lamp Quantity
2
Two Lamps
Lamp Type
14F14T5
17F17T8
Ballast Type
RS Electronic Rapid Start
SD Step-Dimming (100%/50%)
Voltage
120 120 Volts
277 277 Volts
Circuit Quantity
1One
Options
.187 .187" P12 Polycarbonate Lens
AL Marine Grade Aluminum Housing
BSS Brush Stainless Steel Housing
EL 300 Minimum Lumen Battery Pack (90 minutes; 32ºF Starting Temperature)
FS Single Fuse & Holder
KO Two 1/2" EMT Conduit Entry Knockouts (one per end cap)
PSS Painted Stainless Steel Housing
Accessory
9500Torx® with center pin Screwdriver
www.kenall.com
P: 800-4-Kenall
F: 847-360-1781
1020 Lakeside Drive Gurnee, Illinois 60031
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers,
and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.
Content of specification sheets is subject to change; please consult www.kenall.com for current product details. © 2013 Kenall Mfg. Co. All rights reserved.
SH524MS-120313
For additional photometry, go to www.kenall.com
SHERIFF™
SH5 SERIES – Technical Data
DIMENSIONAL DATA
CROSS SECTION
BASEPLATE
5.14"
24.75"
16.00"
3.75"
5.14"
3.75"
(4) .31" Dia.
Mounting Holes
www.kenall.com
P: 800-4-Kenall
F: 847-360-1781
.75" × 1.50"
Oblong
1020 Lakeside Drive Gurnee, Illinois 60031
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers,
and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.
Content of specification sheets is subject to change; please consult www.kenall.com for current product details. © 2013 Kenall Mfg. Co. All rights reserved.
SH524MS-120313