3255
WALL WASH
®
BeveLED
PROJECT INFORMATION
™
Innfinite Coloor+
PROJECT
DATE
TYPE
1" Regress
™
BeveLED In
nfifinnite Color+ Recessed Wall Wash - Illuminate your space with any color available in the spectrum with BeveLED Infinite
Color+. Tune the light from saturated blue, violet, green, yellow, orange, and red, to any of a wide variety of perfect architectural whites with
DMX512 controls. Infinite opportunities abound for hospitality, entertainment, and cultural lighting applications, or any other project requiring full
color and white light flexibility.
1" Regress
1" Regress
Bevel Finish
Color area
Flange Finish
Color area
41⁄2"Ø
51⁄2"Ø
HOW TO SPECIFY
Ordering Example: Specify trim code and housing code to order: Example : 3255W - B1- 10 - LRTW4 - 6032 - WRGB1 - 30KS - NC - 277V - DMX1M - RJ - CB27
TRIM ORDERING INFORMATION
3255
3255
Round
Wall Wash
1" Regress
™
BEVEL STYLE
OPTION
–
______
Wet location 1
W
In
nfinite Color+ Spectrum
FLANGE FINISH
Relative Output (W/nm)
TRIM
–
B1 1” Regress Bevel,
Painted Die Cast
Matches Flange Finish
AB1 1” Regress Bevel,
Black Anodized
AC1 1” Regress Bevel,
Clear Matte Anodized
1 Wet location, use with B1
trims only.
01 Clear Matte
(AC Bevel only)
02 Black Anodized
(AB Bevel only)
10 White
13 Statuary Bronze
21 Black
28 Metalized Grey
RAL Custom Color
(specify RAL #)
1
0.8
0.6
0.4
0.2
0
400
450
500
550
600
650
700
750
wavelength (nm)
Independently mix white light with color in any combination
imaginable to create a uniquely personal light source.
HOUSING ORDERING INFORMATION
HOUSING CODE
WATTAGE
–
LRTW4
LRTW4
– WRGB1
6032
6032 32W LED,
1225
Lumen
Maximum
PRIMARY
WHITE
ENGINE
CODE
WRGB1
–
30KS
30KS 3000K,
80+ CRI
–
NC New Construction
CP Chicago Plenum 2
IC Insulation-Contact
Rated / Airtight 2
2
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
VOLTAGE
HOUSING TYPE
–
120V
277V
ACCESSORIES
–
–
RJ RJ45 Jacks
DMX1M EldoLED DMX 0.1%
dimming, manual
WR Splice Connection
addressing using
XL XLR5 Connectors 3
RDM protocol, 8 bit
DMX2M EldoLED DMX 0.1%
dimming, manual
addressing using
RDM protocol, 16 bit
3 Requires above ceiling
access; N/A with IC or CP
housings.
Not available with EM.
1126 River Road
New Windsor, NY 12553
CABLING
DIMMING DRIVER
–
T 845–565–8500
F 845–561–1130
CB27
CB52
EML
EMLW
27” C-Channel Bars
52” C-Channel Bars
Emergency battery 4
Emergency battery,
wet location 4
4
For use with NC housing
only. Provided with remote test
switch.
© 2015. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 09/24/2015
WALL WASH
®
BeveLED Innfinite Coloor+
™
3255
TRIM INFORMATION
1" Regress
1" Regress
Bevel Finish
Color area
Flange Finish
Color area
41⁄2"Ø
51⁄2"Ø
HOUSING INFORMATION
New Construction
Universal Style Housing - NC
Chicago Plenum - CP
IC / Airtight - IC
7"
85/8"
11/8"
7"
11/8"
7"
13"
13"
185/8" (Plan View)
185/8" (Plan View)
22 /8" (Plan View)
221/8" (Plan View)
1
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2015. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 09/24/2015
WALL WASH
®
BeveLED Innfinite Coloor+
™
3255
SPECIFICATIONS
TRIM: 4-1/2” round aperture with a 1” regressed bevel
and 1/2” flange, retained by two mounting clips. Die cast
aluminum bevel is self flanged and available in white,
statuary bronze, black, and metalized grey finishes. Also
available in black or clear matte bevel with self finish or
painted flange. Custom color flanges available (provide
RAL#).
CABLING: The DMX512 driver is provided with two twisted
pair cabling for connection with communication controls.
Data cables must be run in series between fixtures. Choose
your preferred method of connection when specifying. To
avoid signal transmission problems, a DMX link terminator
should be used in the last fixture in a series. NOTE:
Communication cables and AC power lines must not be run
in the same conduit.
TRIM LENS: Trim is shipped with micro diffusion wall wash
lens.
REFLECTOR: Proprietary precision injection molded wall
wash reflector.
ADJUSTMENT: 362° horizontal rotation, lockable.
FIELD REPLACEABLE LIGHT ENGINE: Available in 1 lumen
package: typical power draw is 23 input watts with 1025
delivered lumens. Maximum power draw is 32 input watts
with up to 1225 delivered lumens. Engine is field replaceable
through the aperture without tools.
• RJ Cabling Option: fixture is provided with a DMX512
interface board inside the junction box with RJ45 jacks for
use with CAT5 cable terminated with RJ45 connectors.
For USAI Lighting fixtures with RJ45/CAT5 connections,
the following ANSI/TIA/EIA-568 pin out standard is used.
Link termination dip switch is provided at the connector
board; no separate link termination device is required. See
dimming compatibility pages for drawings and more details
on this configuration.
EMERGENCY: Emergency lighting battery pack with
remote test switch is serviceable through aperture
for NC housings. Bodine BSL26C provides 200mA
for 90 minutes; delivers ~200-300 lumens. EMLW
wet location option is available with B1 trim only
and requires remote test switch. EM option is not
available with IC or CP housings.
MOUNTING: Butterfly brackets and adjustable
nailer bars with integral nails provided. Nailer bars
are extendible from 14” to 24” centers.
HOUSING: Fabricated of 20 ga. galvanized steel
with thru wire J-box, 4 in 4 out at min. 90°C, #12
AWG thru branch circuit wiring.
MAXIMUM CEILING THICKNESS: As per drawings
above.
CEILING CUT OUT: 5-1/16” Ø
LISTINGS: Dry/Damp. *Wet location option
available with B1 trim only. NRTL/CSA-US tested to
UL standards. IBEW union made.
COLOR: BeveLED Infinite Color+ is capable of creating
any color desired in the spectrum, from saturated blue,
violet, green, yellow, orange, and red, to a wide variety of
architectural whites. All color change is digitally controlled
through the DMX interface of your choice.
WARRANTY: 5 years
NOTES:
• Not for use in corrosive environment.
• WR Cabling Option: no interface board is supplied; cables
• Use of pressure washer voids warranty.
must be spliced inside the junction box for connection. The
PHOTOMETRICS: Consult factory or website for IES
data
cable
used
must
meet
the
following
requirements:
THERMAL MANAGEMENT: Proprietary high performance
files. Tested in accordance with IESNA LM79-2008.
• type: shielded, 2-conductor twisted pair
aluminum die cast heatsink for maximum LED life. Ambient
• maximum capacitance between conductors: 30 pF/ft
temperatures at fixture location should not exceed 40°C
• maximum capacitance between conductor and
during normal operation.
shield: 55 pF/ft
FIELD REPLACEABLE DIMMING DRIVER: Solid state
• maximum resistance: 0.02 ohms/ft
electronic constant current DMX512 8-bit driver with a
• normal impedance: 100-140 ohms
high power factor provided standard. Specify 120V or 277V.
• conductive core: 24 AWG is recommended
Driver complies with IEEE C62.41 surge protection. Specify
If
3-wire
data cables are preferred, we suggest a Belden
DXM1M for 8-bit communication controls; specify DMX2M
for 16-bit communication controls. All driver options require 9841 or equivalent cable which meets the specifications for
remote device management (RDM) communication protocol EIA RS-485 applications. Do not use standard microphone
cables: they cannot transmit DMX512 data reliably over
for addressing.
long distances. NOTE: DMX link termination device (by
others) should be used on last fixture in line on a circuit to
avoid signal loss.
RATED LIFE: Based on IESNA LM80-2008 50,000 hours at
70% lumen maintenance (L70).
• XL Cabling Option: fixture is provided with a DMX512
interface board on the junction box with standard 5-pin
XLR5 jacks which accept XLR5 connectors for DMX
communication. Any standard XLR cable can be used for
this option. Link termination dip switch is provided at the
connector board; no separate link termination device is
required. NOTE: This cabling option requires above ceiling
access.
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2015. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 09/24/2015
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DMX1M, DMX2M
®
BeveLED Innfinite Coloor+
™
DIMMING DRIVER WIRING SCHEMES:
DMX1M: EldoLED DMX dimming with manual addressing, 8-bit (Dims down to 0%)
DMX2M: EldoLED DMX dimming with manual addressing, 16-bit (Dims down to 0%)
Choose from WR (splice connection), RJ (RJ45 jacks) and XL (XLR5 connectors) cabling options,
and refer to corresponding wiring diagram below:
4 BLUE
3
DMX (-)
GREEN/ WHITE
2 ORANGE
DMX (+) 1
BLUE / WHITE
5
GREEN
6
BROWN / WHITE
7
ORANGE/WHITE
BROWN
8 SHIELD
CAT 5 CABLE
RJ CABLING OPTION
RJ-45 CONNECTORS
DMX DATA IN
DMX DATA OUT
ON
DMX+
ON
DMXSHIELD
TURN ON DIP SWITCH
TO TERMINATE LAST
FIXTURE ON DMX BUS
OFF
OFF
LOAD
LINE
V+
DRIVER
NEUTRAL
V-
GROUND
WR OPTION
DMX DATA IN
DMX DATA OUT
DMX+ BLUE
DMX+
DMX- WHITE
DMX-
SHIELD-
SHIELD
• WR Cabling Option: no interface board is supplied; cables
must be spliced inside the junction box for connection. The
data cable used must meet the following requirements:
• type: shielded, 2-conductor twisted pair
• maximum capacitance between conductors: 30 pF/ft
• maximum capacitance between conductor and
shield: 55 pF/ft
• maximum resistance: 0.02 ohms/ft
• normal impedance: 100-140 ohms
• conductive core: 24 AWG is recommended
LOAD
DRIVER
LINE
NEUTRAL
V+
V+
V-
V-
If 3-wire data cables are preferred, we suggest a Belden
9841 or equivalent cable which meets the specifications for
EIA RS-485 applications. Do not use standard microphone
cables: they cannot transmit DMX512 data reliably over
long distances. NOTE: DMX link termination device (by
others) should be used on last fixture in line on a circuit to
avoid signal loss.
GROUND
XL CABLING OPTION
NOTE: This cabling option requires above ceiling access.
4.75"
XLR CABLE
5 PIN XLR CONNECTORS
MALE FEMALE
DMX DATA IN
1.-10"
DMX DATA OUT
XLR CONNECTORS WHEN XLR5 IS
SELECTED LEAVE CLEARANCE FOR
J-BOX TO SLIDE TO APERTURE
Off
DMX+
On
DMX-
Termination
1-1/8"
SHIELD
TERMINATION
LOAD
TURN ON DIP
SWITCH TO
TERMINATE
LAST FIXTURE
ON DMX BUS
V+
LINE
DRIVER
NEUTRAL
V-
GROUND
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2014. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-265
®
BeveLED Innfinite Coloor+
™
DIMMING DRIVER WIRING SCHEMES:
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DMX1M, DMX2M
DMX MUST BE DAISY CHAINED IN SINGLE LINE
CORRECT !
INCORRECT !
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
DRIVER
NOTES FOR DRIVERS:
1. DMX signal cable must NOT be run in same conduit as high voltage AC power lines.
2. Fixtures must be daisy chained in one serial line using Data in and Data out
3. Maximum of 32 DMX devices on a single DMX bus
4. Maximum of 1600 ft serial communication link distance
5. To avoid signal loss, DMX signal terminator should be used on last fixture in line. For RJ
and XL cabling options, this is provided through a dip-switch on the connector board. For
WR cabling options, this device (120 ohm resistor) is provided by others.
6. For best results when using WR cabling option use communication data splices.
7. Default state for fixtures off. Luminaire will not light until DMX signal is received.
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2014. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-265