MIL-PRF-38534 CERTIFIED
M.S.KENNEDY CORP.
4707 Dey Road Liverpool, N.Y. 13088
(315) 701-6751
FEATURES:
Manufactured using Space Qualified RH1013 Die
MIL-PRF-38535 Class V Processing & Screening
Total Dose Tested to TBD Krads(Si) (Method 1019.7 Condition A)
Single Supply Operation
Low Offset Voltage
Low Drift
Available in Straight or Gull Wing Lead Form
Contact MSK for MIL-PRF-38535 Qualification and Radiation Status
DESCRIPTION:
The MSK 114RH is a radiation hardened quad operational amplifier for use in space and severe military applications. This device offers low offset voltage, low drift, low offset current and high gain combined with a space efficient 14 pin surface mount flat pack. The MSK 114RH is an ideal solution when multiple precision amplifiers are required and board space is at a premium. The MSK 114RH 14 pin ceramic flat pack is offered with straight leads or gull wing for surface mount applications.
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS
Battery Powered Precision Instrumentation
Multiple Limit Threshold Detection
Active Filters
Multiple Gain Blocks
Instrumentation Amplifiers
1
5
6
7
3
4
1
2
PIN-OUT INFORMATION
OUT A
-IN A
+IN A
+VCC
+IN B
-IN B
OUT B
14
13
12
11
10
9
8
OUT D
-IN D
+IN D
-VCC
+IN C
-IN C
OUT C
PRELIMINARY Rev. - 10/09

ABSOLUTE MAXIMUM RATINGS 7
±VCC
V
IN
Supply Voltage
Input Voltage
○
○
○
○
○
○ ○ ○
Differential Input Voltage
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Equal to Positive Supply Voltage
5V Below Negative Supply Voltage
Output Short Circuit Duration
○ ○ ○ ○ ○ ○ ○
±22V
±30V
Indefinite
T
ST
T
LD
T
T
J
C
Storage Temperature Range
Lead Temperature Range
(10 Seconds)
○ ○ ○ ○ ○
Junction Temperature
○
○
○
○
○
○
○
○
○ ○ ○
-65°C to +150°C
○
300°C
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
150°C
Case Operating Temperature Range
MSK 114RH
MSK 114VRH
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○ ○
○ ○
○ ○
○
○
-40°C to+85°C
-55°C to +125°C
ELECTRICAL SPECIFICATIONS
6
7
8
NOTES:
3
4
1
2
5
Unless otherwise specified; ±VCC=±15V
DC
, V
CM
=0V.
Devices shall be capable of meeting the parameter, but need to be tested. Typical parameters are for reference only.
Industrial grade devices shall be tested to subgroup 1 unless otherwise specified.
Military grade devices ('V' Suffix) shall be 100% tested to subgroups 1,2,3 and 4.
Subgroup 1, 4 T A =T C =+25°C
Subgroup 2, 5 T
A
=T
C
=+125°C
Subgroup 3, 6 T
A
=T
C
=-55°C
Refer to SMD TBD for electrical parameters for devices purchased as such.
Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
Pre and Post irradiation limits at 25°C, to TBD Krads TID, are identical unless otherwise specified.
PRELIMINARY Rev. - 10/09
2

APPLICATION NOTES
SINGLE SUPPLY OPERATION
The MSK 114RH may be used in single supply applications where the negative supply is 0 volts. The device incorporates unique phase reversal protection circuitry to avoid the most common problems occurring during single supply operation. The phase reversal protection circuitry, however does not function when one specific amplifier of the other three is driven hard into negative saturation at the output. Phase reversal protection does not work under the following conditions: Amplifier A and D when the opposite output is negative saturation. Amplifiers B and C outputs have no effect. Amplifier B or C when the opposite output is in negative saturation. Amplifiers
A and D outputs have no effect. The MSK 114RH all-NPN output stage maintains it's low output resistance and high gain characteristics until the output is saturated. In dual supply applications, the output stage will remain crossover distoration-free. The minimum single supply voltage for proper operation of the MSK 114RH is +5
Volts.
TOTAL DOSE RADIATION TEST
PERFORMANCE
Radiation performance curves for TID testing will be generated for all radiation testing performed by MS Kennedy. These curves show performance trends throughout the TID test process and will be located in the MSK 114RH radiation test report. The complete radiation test report will be available in the RAD HARD PRODUCTS section on the MSK website.
ADDITIONAL APPLICATION INFORMATION
For additional applications information, please reference Linear Technology Corporation's® LT1013/1014 and RH1014 data sheets.
FIGURE 1
FIGURE 2
3
PRELIMINARY Rev. - 10/09

TYPICAL PERFORMANCE CURVES
4
PRELIMINARY Rev. - 10/09

MECHANICAL SPECIFICATIONS
ESD TRIANGLE INDICATES PIN 1
WEIGHT=TBD
MSK114 V RH
LEAD CONFIGURATIONS
BLANK= STRAIGHT
RADIATION HARDENED
SCREENING
BLANK= INDUSTRIAL
V=MIL-PRF-38535 CLASS V
GENERAL PART NUMBER
The above example is a Class V device with straight leads.
5 PRELIMINARY Rev. - 10/09

ESD TRIANGLE INDICATES PIN 1
WEIGHT=TBD
MSK114 V RH G
LEAD CONFIGURATIONS
G=GULL WING
RADIATION HARDENED
SCREENING
BLANK= INDUSTRIAL
V=MIL-PRF-38535 CLASS V
GENERAL PART NUMBER
The above example is a Class V device with gull wing leads.
M.S. Kennedy Corp.
4707 Dey Road, Liverpool, New York 13088
Phone (315) 701-6751
FAX (315) 701-6752 www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products.
Please visit our website for the most recent revision of this datasheet.
Contact MSK for MIL-PRF-38535 Class V and radiation status.
6 PRELIMINARY Rev. - 10/09