wiring diagrams

advertisement
wiring diagrams
561C, G
561S, W
1 AND 3 PHASE, 60 HERTZ
AIR CONDITIONING UNIT
Cancels:
WD 561C.18.5
WD 561C.18.6
3-99
SCHEMATIC DIAGRAM (LADDER FORM)
CONNECTION DIAGRAM
(NOTE #9)
*CH
BLK
or
RED
RED or BLK
COMP
BLU
S
BLK C
H
21
R
C
YEL
23
YEL
F
OFM
BRN
BLK
CONT
L1
208/230 1Ø
POWER
SUPPLY
11
L2
23
EQUIP
GND
BRN
(NOTE #14)
BLU
BLU
BLU
CAP
11
*ST
BRN
1
YEL
BLK
BLK
*SC
(NOTE #8)
2
23
23
CAP
CONT
*LPS
*DTS
T2
LOGIC
LOGIC
T1
T3
T1
T3
* CTD
*LLS
Y
IFR
BLK
C
R
G
CONT
(NOTE #14)
BRN
Y
H
OFM
C
F
*HPS
*LLS
BLK
*ST
+t
*SC
1
* CTD
BLU
BLU
S
2
5
*SR
T2
YEL
L2
21
5
*SR
YEL
BLK
YEL
COMP
R
C
EQUIP
GND
VIO
BLU
*CH
CONT
+t
YEL
*LPS
*DTS
*HPS
BLU
L1
BLK
EXTERNAL
POWER
SUPPLY
24 V
(NOTE #3)
G
R
C
R
INDOOR
THERMOSTAT
EXTERNAL POWER SUPPLY 24 V
R
INDOOR BLOWER MOTOR
INDOOR THERMOSTAT
(NOTE #6)
-LEGENDFACTORY POWER WIRING
FACTORY CONTROL WIRING
FIELD CONTROL WIRING
FIELD POWER WIRING
COMPONENT CONNECTION
FIELD SPLICE
JUNCTION
-NOTESCAP
CAPACITOR (DUAL RUN)
*CH
CRANKCASE HEATER
COMP
COMPRESSOR
*CTD
COMPRESSOR TIME DELAY
*DTS
DISCHARGE TEMP. SWITCH
*HPS
HIGH PRESSURE SWITCH
IFR
INDOOR FAN RELAY
*LLS
LIQ. LINE SOLENOID VALVE
*LPS
LOW PRESSURE SWITCH
OFM
OUTDOOR FAN MOTOR
*SC
START CAPACITOR
*SR
START RELAY
START THERMISTOR
CONT
CONTACTOR
*ST
CAP
CAPACITOR (DUAL RUN)
* MAY BE FACTORY OR FIELD INSTALLED.
1. Symbols are electrical representation only.
2. Compressor and fan motor furnished with
inherent thermal protection.
3. To be wired in accordance with National Electric
N.E.C. and local codes.
4. N.E.C. class 2, 24 V circuit, min. 40 VA required,
60 VA on units installed with lls.
5. Use copper conductors only.
6. Typical cooling only thermostat, for other
arrangements see installation instructions.
7. If indoor section has a transformer with a
grounded secondary, connect the grounded side
to the BRN lead.
8. When start relay and start capacitor are installed,
start thermistor is not used.
9. CH not used on all units.
10. If any of the original wire, as supplied must be
replaced, use the same or equivalent wire.
11. Check all electrical connections inside control box
for tightness.
12. Do not attempt to operate unit until service valves
have been opened.
13. Do not rapid cycle compressor. Compressor must
be off 3 minutes to allow pressures to equalize
between high and low side before starting.
14. Wire not present if HPS, LPS, DTS or CTD are
used.
CAUTION
1. Compressor damage may occur if system is over
charged.
2. This unit is factory charged with R-22 in
accordance with the amount shown on the rating
plate. The charge is adequate for most systems
using matched coils and tubing not over 15 feet
long. The best performance will be achieved when
the unit operates with a suction gas superheat at
the compressor inlet of 5 °F at normal rating
conditions of the air conditioning and
refrigeration institute (ARI). This chart may be
used to approximate the charge if ARI rating
conditions cannot be obtained. ARI rating
conditions are equivalent to DOE test "A"
conditions. See product data literature for required
indoor air flow rates and for use of line lengths
over 15 Ft.
3. Carefully relieve refrigerant pressure within this
unit before final disposal.
317738-401 REV. C
A95084
Fig. 1—561(C, G, S, W)018, 024, 030, 036, 042, 048 208-230v, 1 Phase, 60 Hertz
—1—
CONNECTION DIAGRAM
*CH (NOTE #9)
RED or BLK
-LEGEND-
BLK
BLU
FACTORY POWER WIRING
FACTORY CONTROL WIRING
FIELD CONTROL WIRING
C
FIELD POWER WIRING
11 21
YEL
BRN
1 2
YEL R
13 23
COMPONENT CONNECTION
*SC
F
5
YEL
(NOTE #8)
FIELD SPLICE
*SR
OFM
EQUIP
CONT
BRN
JUNCTION
GND
BLK
CONT CONTACTOR
CAP CAPACITOR (DUAL RUN)
BLU
BRN
(NOTE #14)
*CH
CRANKCASE HEATER
BLK
VIO
COMP COMPRESSOR
YEL
*CTD COMPRESSOR TIME DELAY
*DTS
*HPS
*LPS
T2
*DTS DISCHARGE TEMP. SWITCH
BLK YEL
BLU
BLU BLK
LOGIC
YEL
*HPS HIGH PRESSURE SWITCH
T3
T1
IFR
INDOOR FAN RELAY
*CTD
BRN
*LLS LIQ. LINE SOLENOID VALVE
*LLS
*LPS LOW PRESSURE SWITCH
BLU
BLK
BLK
EXTERNAL POWER OFM OUTDOOR FAN MOTOR
C
BLU
SUPPLY 24V
R
*SC
START CAPACITOR
(NOTES #3 & #6)
IFR
*SR
START RELAY
*ST
START THERMISTOR
* MAY BE FACTORY OR FIELD
Y G R
INSTALLED.
CAP
YEL
+t°
SCHEMATIC DIAGRAM
*CH
L2
(LADDER FORM)
C
CONT
21
11
*ST
INDOOR BLOWER MOTOR
INDOOR THERMOSTAT (NOTE #5)
L1
BLU
COMP BLU
S
H
BLK C
RED or BLK
L1
208/230 1Ø L2
POWER
SUPPLY
5
EQUIP
GND
R
COMP
S
2
1
*SR
*ST
+t°
*SC
OFM
H
C
F
CONT
CAP
23
13
(NOTE #14)
*CTD
*HPS
*DTS
*LPS
CONT
T2
LOGIC
T1
T3
*LLS
Y
G
R
INDOOR THERMOSTAT
IFR
R C
EXTERNAL POWER SUPPLY 24 V
-NOTES-
1. Symbols are electrical representation only.
2. Compressor and fan motor furnished with inherent thermal
protection.
3. To be wired in accordance with National Electric N.E.C.
and local codes.
4. N.E.C. class 2, 24 V circuit, min. 40 VA required, 60 VA on
units installed with LLS.
5. Use copper conductors only.
6. Connection for typical cooling only thermostat, for other
arrangements, see installation instructions.
7. If indoor section has a transformer with a grounded
secondary, connect the grounded side to the BRN lead.
8. When start relay and start capacitor are installed, start
thermistor is not used.
9. CH not used on all units.
10. If any of the original wire, as supplied, must be replaced,
use the same or equivalent wire.
11. Check all electrical connections inside control box for
tightness.
12. Do not attempt to operate unit until service valves have
been opened.
13. Do not rapid cycle compressor. Compressor must be off
3 minutes to allow pressures to equalize between high
and low side before starting.
14. Wire not present if HPS, LPS, DTS or CTD are used.
321939-101 REV. B
A95018
Fig. 2—561(C, G, S, W)060 208-230v, 1 Phase, 60 Hertz
—2—
CONNECTION DIAGRAM
COMP
BLU
CONT
L1
11
L3
21
13
T2
EQUIP
GND
T3
YEL
23
EQUIP GND
CONT
COMP
T1
BLK
L2
L1
RED or BLK
RED or BLK
L2
208/230 3Ø
POWER
SUPPLY
SCHEMATIC DIAGRAM (LADDER FORM)
*CH (NOTE #8)
11
CAP
21
*CH
T3
CAP
YEL
OFM
L3
T2
T1
CONT
13
23
OFM
BRN
BLK
ALERT !
SEE NOTE #11
YEL
BRN
BLK
VIO
*HPS
*LPS
BLU
BLU
YEL
CONT
T2
YEL
T2
T3
T1
LOGIC
T1
CTD
BLU
*LLS
BRN
*LLS
BLK
C
R
IFR
G
R
INDOOR
THERMOSTAT
R
INDOOR THERMOSTAT
(NOTE #5)
-NOTES-
FACTORY POWER WIRING
*CH
FACTORY CONTROL WIRING
COMP
COMPRESSOR
*CTD
COMPRESSOR TIME DELAY
IDF
INDOOR FAN
*HPS
HIGH PRESSURE SWITCH
IFR
INDOOR FAN RELAY
*LLS
LIQ. LINE SOLENOID VALVE
*LPS
LOW PRESSURE SWITCH
OFM
OUTDOOR FAN MOTOR
CRANKCASE HEATER
FIELD CONTROL WIRING
COMPONENT CONNECTION
FIELD SPLICE
JUNCTION
CONT
CONTACTOR
CAP
CAPACITOR (DUAL RUN)
EXTERNAL POWER SUPPLY 24 V
INDOOR BLOWER MOTOR
-LEGEND-
FIELD POWER WIRING
C
R
(NOTES #3 & #6)
G
T3
CTD
Y
EXTERNAL
POWER
SUPPLY
24 V
BLK
IFR
Y
*LPS
*HPS
LOGIC
* MAY BE FACTORY OR FIELD INSTALLED.
1.
2.
CAUTION
Symbols are electrical representation only.
1. Compressor damage may occur if system is over
Compressor and fan motor furnished with inherent
thermal protection.
charged.
3. To be wired in accordance with National Electric
2. This unit is factory charged with R-22 in
N.E.C. and local codes.
accordance with the amount shown on the rating
4. N.E.C. class 2, 24 V circuit, min. 40 VA required,
60 VA on units installed with lls.
plate. The charge is adequate for most systems
5. Use copper conductors only.
using matched coils and tubing not over 15 feet
6. Typical cooling only thermostat, for other
long. The best performance will be achieved when
arrangements see installation instructions.
the unit operates with a suction gas superheat at
7. If indoor section has a transformer with a grounded
secondary, connect the grounded side to the BRN lead.
the compressor inlet of 5 °F at normal rating
8. If any of the original wire, as supplied must be
conditions of the air conditioning and
replaced, use the same or equivalent wire.
refrigeration institute (ARI). This chart may be
9. Check all electrical connections inside control box
for tightness.
used to approximate the charge if ARI rating
10. Do not attempt to operate unit until service valves
conditions cannot be obtained. ARI rating
have been opened.
conditions are equivalent to DOE test "A"
11. Do not rapid cycle compressor. Compressor must
be off 3 minutes to allow pressures to equalize
conditions. See product data literature for required
between high and low side before starting.
indoor air flow rates and for use of line lengths
12. It is imperative to connect 3Ø field power to unit with
over 15 Ft.
correct phasing. wrong phasing will cause reverse
3. Carefully relieve refrigerant pressure within this
rotation of scroll compressor which will result in
reduced current draw, elevated noise level and
unit before final disposal.
improper operation. If rotation is reversed, simply
interchange any two of the three power connections
319390-401 REV.C
on field side.
A94414
Fig. 3—561(C, W)030, 036, 042, 048, 060 208/230v
and 561C036, 042, 048, 060 460v, 3 Phase, 60 Hertz
—3—
SERVICE TRAINING
Packaged Service Training programs are an excellent way to increase your
knowledge of the equipment discussed in this manual, including:
• Unit Familiarization
• Maintenance
• Installation Overview
• Operating Sequence
A large selection of product, theory, and skills programs is available, using popular
video-based formats and materials. All include video and/or slides, plus companion
book.
Classroom Service Training plus "hands-on" the products in our labs can mean
increased confidence that really pays dividends in faster troubleshooting, fewer
callbacks. Course descriptions and schedules are in our catalog.
CALL FOR FREE CATALOG 1-800-962-9212
[ ] Packaged Service Training
© 1999 Bryant Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231
[ ] Classroom Service Training
—4—
Printed in U.S.A.
561c186
Catalog No. 5356-108
Download