NZQA Expiring unit standard
10135 version 6
Page 1 of 5
Title
Operate a flat bed die cutter for complex new work in the corrugated
packaging industry
Level
4
Credits
35
Purpose
People credited with this unit standard are able to: plan ahead,
to avoid delays during make ready and during production
running; communicate to ensure job requirements are met;
make ready the machine to make die cut and stripped product
without avoidable delays; run the machine, in accordance with
workplace practices, to make die cut and stripped product to
meet job requirements; and follow safety requirements for the
machine being used.
Classification
Fibreboard Packaging > Corrugated Case Converting
Available grade
Achieved
Entry information
Critical health and
safety prerequisites
Unit 340, Demonstrate knowledge of safe working practices in
the printing and graphic pre-press industries, or demonstrate
equivalent knowledge and skills.
Recommended skills
and knowledge
Unit 10134, Operate a flat bed die cutter for repeat work in the
corrugated packaging industry; Unit 21276, Make ready a flat
bed die cutter in the corrugated packaging industry; and Unit
10133, Make ready for automatic stripping at a flat bed die
cutter in the corrugated packaging industry; or demonstrate
equivalent knowledge and skills.
Explanatory notes
1
All workplace practices must meet any applicable and recognised codes of practice,
and documented workplace health, safety, and environmental procedures for
personal, product, workplace health, safety, and environmental matters, and the
obligations required under current law including the Health and Safety in Employment
Act 1992, Hazardous Substances and New Organisms Act 1996, Resource
Management Act 1991, Privacy Act 1993 and their subsequent amendments.
2
Workplace practices refer to the documented procedures for the machine and/or
workplace.
3
Complex jobs are those that meet the requirements of explanatory note 6.
Competenz
SSB Code 101571
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
10135 version 6
Page 2 of 5
4
Board warped in excess of 2% is not to be used during assessment. The process for
defining and calculating warp percentage is as follows: when a warped board is laid
on a level surface so as to form a shallow arch, the maximum vertical deviation from
the horizontal is expressed as a percentage of the board dimension that forms the
arch.
5
Assessments must be conducted where board sheet size is 20% above the
machine’s specified minimum limit and 20% below the machine’s specified maximum
limit.
6
Competence in this unit standard must be demonstrated in a production task
requiring cutting and creasing and perforating, internal and external stripping, and the
production of multiple ups involving either one or two units behind each other.
7
The production task must be either a new one within the workplace, or involve the
use of a new die or a reknived die.
8
Competence must be demonstrated at a flat bed die cutter configured with a hopper
feeder, automated take off, and stripping capability.
Outcomes and evidence requirements
Outcome 1
Plan ahead, to avoid delays during make ready and during production running.
Evidence requirements
1.1
Procedures for the handling of priority orders where special job prioritisation is
scheduled are described and followed in accordance with workplace practices.
1.2
Before make ready work begins, production order documentation is confirmed
as the documentation required for the next job scheduled.
1.3
Identification for the initial pallet load or slip sheet load is prepared in advance
of production running in accordance with workplace practices.
1.4
All required materials and documentation are confirmed as available prior to
make ready.
Range
Competenz
SSB Code 101571
may include but is not limited to – make ready sheets, dies,
samples, lay cards, overlays, slip sheets, pallets, tools, board to
be run, load identification, production order, matrix, stripping unit.
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
10135 version 6
Page 3 of 5
Outcome 2
Communicate to ensure that job requirements are met.
Evidence requirements
2.1
Any forward rescheduling to match up similar jobs is agreed with other staff in
accordance with workplace practices.
Range
2.2
Staff responsible for delivering materials for the next job are clearly advised of
the requirements in accordance with workplace practices ensuring that no
avoidable delays occur.
Range
2.3
forkhoist operators, pre-press, own machine crew.
Machine crew confirm that they understand the specific make ready and
production tasks they are responsible for.
Range
2.4
supervisor, manager, planning department.
task responsibilities – stripping down machine from the previous
job, setting up for the next job, checks at feed end, checks to be
made at take off.
Potential problems during make ready and production, and any special
production needs are identified, and their requirements are met through clear
communication with crew members.
Outcome 3
Make ready the machine to make die cut and stripped product without avoidable delays.
Evidence requirements
3.1
Make ready is completed in accordance with workplace practices and to meet
job requirements.
Range
time allowed, board condition;
job requirements may include – run length, print specifications,
take off requirements, number of ups in die cutting.
Outcome 4
Run the machine, in accordance with workplace practices, to make die cut and stripped
product to meet job requirements.
Evidence requirements
4.1
Production running speed is maintained ensuring that required quality and
production standards are met.
Competenz
SSB Code 101571
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
10135 version 6
Page 4 of 5
4.2
Checks for faults are carried out during production running.
4.3
Action is immediately taken to identify and rectify any faults, and fault-free
production running is successfully resumed.
4.4
Proactive measures to reduce the likelihood of faults occurring during
production are followed.
Range
proactive measures may include but are not limited to checks on –
machine settings and machine running, condition of board being
input, condition of finished product at take off.
4.5
Actions available to counter the effect of board warp exceeding 2% are
explained in terms of workplace practices.
4.6
Load identification is carried out to meet job requirements.
4.7
Cutting, creasing and die cutting to print are all achieved.
4.8
Die cut to print is achieved and maintained.
4.9
Internal and external scrap is removed.
4.10
Counting, batching, and ejecting are carried out.
4.11
Job is stacked.
4.12
Documentation is completed.
Range
may include but is not limited to – internal fault error sheets, time
sheets, record of waste, production order data, quality control
data, machine fault reports, feed stock sheets, maintenance
sheets, load identification, provision of product sample(s), final
count confirmation, information required for the next time the job is
run.
Outcome 5
Follow safety requirements for the machine being used.
Range
operating manual, workplace practices.
Evidence requirements
5.1
Machine start up, shutdown and emergency procedures in the workplace are
explained.
5.2
Hazard control measures, as circulated by the company, are described and
followed.
5.3
Hazards or potential hazards in the workplace are identified and reported in
accordance with workplace practices.
Competenz
SSB Code 101571
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
Replacement information
10135 version 6
Page 5 of 5
This unit standard, unit standard 10134, and unit
standard 21726 have been replaced by unit standard
27793.
This unit standard is expiring. Assessment against the standard must take place by
the last date for assessment set out below.
Status information and last date for assessment for superseded versions
Process
Version Date
Last Date for Assessment
Registration
1
18 February 1998
31 December 2015
Revision
2
27 March 2001
31 December 2015
Review
3
27 April 2005
31 December 2015
Rollover
4
12 December 2008
31 December 2015
Review
5
20 September 2012
31 December 2019
Rollover
6
10 December 2015
31 December 2019
Consent and Moderation Requirements (CMR) reference
0005
This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note
Providers must be granted consent to assess against standards (accredited) by NZQA,
before they can report credits from assessment against unit standards or deliver courses
of study leading to that assessment.
Industry Training Organisations must be granted consent to assess against standards by
NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and
which are assessing against unit standards must engage with the moderation system that
applies to those standards.
Requirements for consent to assess and an outline of the moderation system that applies
to this standard are outlined in the Consent and Moderation Requirements (CMR). The
CMR also includes useful information about special requirements for organisations wishing
to develop education and training programmes, such as minimum qualifications for tutors
and assessors, and special resource requirements.
Competenz
SSB Code 101571
 New Zealand Qualifications Authority 2016