8
CATALOG NO.
F
7
TERMINAL TYPE
JM60060-1CR
BOX LUG
JM60060-2CR
BOX LUG
JM60060-3CR
BOX LUG
6
IP20 FINGER SAFE COVERS
W/O INDICATION
INDICATION
5
3
2
1
REVISIONS
NO. OF
POLES
REV
ZONE
A
1
CVR-J-60060
4
DESCRIPTION
DATE
ECN
BY
PRE-RELEASE
5/8/14
BU-SB14TBD
AVM
2
CVRI-J-60060
F
3
PROVISION FOR
MARKER LABEL
SEE NOTE 8
114
4.5
77
3.0
39
1.5
7
.3
E
PROVISION FOR
MARKER LABEL
SEE NOTE 8
CVR-J-60060 (NON INDICATING)
CVRI-J-60060 (WITH INDICATION)
E
R3
.1
94
3.7
5
.2
18
.7
38
1.5
38
1.5
D
53
2.1
C
PROVISION FOR
MARKER LABEL
SEE NOTE 8
119
4.7
18
.7
113
4.5
75
3.0
D
LOCKOUT - TAGOUT RING
SEE NOTE 6
65
2.6
1-POLE
JM60060-1CR
2-POLE
JM60060-2CR
C
JM60060-1CR
SHOWN WITH COVER
3-POLE
JM60060-3CR
NOTES:
B
SLA3_BUSS_NAE_GENRL_REV_A
A
1) VOLTAGE RATING: 600V
2) AMPERAGE: 60A
3) WITHSTAND RATING: 200kA
4) WIRE: CU/AL 75C
5) WIRE RANGE:
(1) 2 - 14 AWG CU
2-3: 50 lb-in (5.6 Nm)
4-6, 45 lb-in (5.1 Nm)
8, 40 lb-in (4.5 Nm)
10-14, 35 lb-in (4.0 Nm)
(1) 2 - 8 AWG AL
2-3: 50 lb-in (5.6 Nm)
4-6, 45 lb-in (5.1 Nm)
8, 40 lb-in (4.5 Nm)
6) USE 4mm DIA. CABLE LOCK OR 1/4" DIA. HASP PADLOCK.
7) RECOMMEND USING DIN-RAIL END STOPS FOR DIN RAIL MOUNTED APPLICATIONS
BUSSMANN PART NUMBERS BRKT-ND OR BRKT-NDSCREW2
8) US BUSSMANN MARKER LABEL TM26CB
9) ALL DIMENSIONS ARE TYPICAL UNLESS OTHERWISE INDICATED
B
MODEL VERSION
MODEL SOURCE DATA
JM60060-xCR
THIS DRAWING IS AN UNCONTROLLED COPY IF
PRINTED OR SENT ELECTRONICALLY,
DO NOT SCALE DRAWING
7
6
APPROVALS
GENERAL DRAWING PRACTICES IN
ACCORDANCE WITH ASME - Y14.100-2004
DIMENSIONS AND TOLERANCES IN
ACCORDANCE WITH ASME - Y14.5M-1994
PRODUCT MANAGER
D. McDowell
ENGINEER
EATON CORPORATION - CONFIDENTIAL AND PROPRIETARY UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION MILLIMETERS TOLERANCES TO BE
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTIANED THEREON,
IS CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON CORPORATION AND
IS MERELY ON LOAN AND SUBJECT TO RECALL BY EATON AT ANY TIME. BY TAKING
POSSESSION OF THE DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT
THIS DOCUMENT CANNOT BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF
EATON AND THAT NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE
REPRODUCED WITHOUT THE PRIOR WRITTEN CONSENT OF EATON. IN THE CASE OF
CONFLICTING CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE
STATUS OF THIS DOCUMENT.
C 2012 Eaton Corporation, All Rights Reserved.
8
3D VIEW FOR JM60060-1CR
WITH COVER
SCALE NONE
3D VIEW FOR JM60060-1CR
SCALE NONE
5
4
ONE PLACE X.X
TWO PLACE X.X X
ALL ANGLES X.X
= ±0.3 mm
= ±0.13 mm
= ± 1°
SPECIAL CHARACTERISTIC
SIGNIFICANT CHARACTERISTIC
THIRD ANGLE PROJECTION
3
A.VZM
QUALITY
--
DATE
5/8/2014
5/8/2014
--/--/----
MATERIAL
(0)
(0)
.
CUSTOMER PRINT
TITLE
N/A
N/A
2
600V / 60A CLASS J FUSE BLOCK
SIZE
DWG NO.
SCALE:
1:2
A3
FINISH
A
JM60060-SERIES-CP
SHEET
1
REV
A
1 OF 2
Tue Oct 01, 2013 4:0X PM GPK
8
7
6
5
4
3
2
1
F
F
CUT COVER TAB
AT NOTCH FOR
USE WITH WIRES
LARGER THAN
8 AWG
E
E
1. HOOK DIN RAIL SNAPS ON ONE SIDE OF THE DIN RAIL
D
D
DETAIL A
SCALE 1 : 1
2. PUSH DOWN TO DEFLECT THE SNAPS
C
C
A
3. ROTATE UNTIL THE
OPPOSITE SIDE SNAPS
ONTO DIN RAIL
B
B
CLOSING
PUSH STRAIGHT DOWN UNTIL SNAPS CLICK
INTO PLACE
INSTALLATION ON DIN RAIL
END STOPS MAY BE NECESSARY FOR SOME
ASSEMBLY CONDITIONS - SEE NOTE 7
OPENING
PULL STRAIGHT UP AT BOTH OUTSIDE
HANDLES
.
CUSTOMER PRINT
SLA3_BUSS_NAE_GENRL_REV_A
A
TITLE
7
6
5
4
3
2
600V / 60A CLASS J FUSE BLOCK
SIZE
DWG NO.
SCALE:
1:2
A3
8
A
JM60060-SERIES-CP
SHEET
1
REV
A
2 OF 2
Tue Oct 01, 2013 4:0X PM GPK