8 7 6 5

advertisement
8
CATALOG NO.
F
7
6
IP20 FINGER SAFE COVERS
TERMINAL TYPE
W/O INDICATION
INDICATION
5
SCREW
1
JM60030-2SR
SCREW
2
JM60030-3SR
SCREW
3
JM60030-1PR
PRESSURE PLATE
1
JM60030-2PR
PRESSURE PLATE
JM60030-3PR
PRESSURE PLATE
3
JM60030-1CR
BOX LUG
1
JM60030-2CR
BOX LUG
2
JM60030-3CR
BOX LUG
3
CVRI-J-60030
3
2
1
REVISIONS
NO. OF
POLES
JM60030-1SR
CVR-J-60030
4
REV
ZONE
A
DESCRIPTION
DATE
ECN
BY
PRE-RELEASE
5/8/14
BU-SB14TBD
AVM
F
2
CVR-J-60030 (NON INDICATING)
CVRI-J-60030 (WITH INDICATION)
55
2.2
E
28
1.1
PROVISION FOR
MARKING LABEL
SEE NOTE 8
83
3.3
R3
.1
87 12
3.4 .5
E
110
4.3
D
D
PROVISION FOR
MARKING LABEL
SEE NOTE 8
46
1.8
17
.7
C
NOTES:
JM60030-1SR
B
SLA3_BUSS_NAE_GENRL_REV_A
A
JM60030-1PR
28
1.1
29
1.1
C
1-POLE
JM60030-1CR SHOWN
2-POLE
JM60030-2CR SHOWN
6
5
3- POLE
JM60030-3CR SHOWN
JM60030-1CR
SHOWN WITH COVER
B
3D VIEW FOR JM60030-1PR
SCALE NONE
MODEL VERSION
MODEL SOURCE DATA
JM60030-XXX
THIS DRAWING IS AN UNCONTROLLED COPY IF
PRINTED OR SENT ELECTRONICALLY,
DO NOT SCALE DRAWING
3D VIEW FOR JM60030-1SR
SCALE NONE
PRODUCT MANAGER
D. McDowell
ENGINEER
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION MILLIMETERS TOLERANCES TO BE
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTIANED THEREON,
IS CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON CORPORATION AND
IS MERELY ON LOAN AND SUBJECT TO RECALL BY EATON AT ANY TIME. BY TAKING
POSSESSION OF THE DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT
THIS DOCUMENT CANNOT BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF
EATON AND THAT NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE
REPRODUCED WITHOUT THE PRIOR WRITTEN CONSENT OF EATON. IN THE CASE OF
CONFLICTING CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE
STATUS OF THIS DOCUMENT.
4
ONE PLACE X.X
TWO PLACE X.X X
ALL ANGLES X.X
= ±0.3 mm
= ±0.13 mm
= ± 1°
SPECIAL CHARACTERISTIC
SIGNIFICANT CHARACTERISTIC
THIRD ANGLE PROJECTION
3
3D VIEW FOR JM60030-1xR
WITH COVER
SCALE NONE
APPROVALS
GENERAL DRAWING PRACTICES IN
ACCORDANCE WITH ASME - Y14.100-2004
DIMENSIONS AND TOLERANCES IN
ACCORDANCE WITH ASME - Y14.5M-1994
EATON CORPORATION - CONFIDENTIAL AND PROPRIETARY UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN
C 2012 Eaton Corporation, All Rights Reserved.
7
LOCKOUT - TAGOUT RING
SEE NOTE 6
58
2.3
1) VOLTAGE RATING: 600V
2) AMPERAGE: 30A
3) WITHSTAND RATING: 200kA
4) WIRE: CR = CU/AL 75C
SR/PR = CU75C/90C
5) -CR WIRE RANGE:
(1) 2 - 14 AWG CU
2-3: 50 lb-in (5.6 Nm)
4-6, 45 lb-in (5.1 Nm)
8, 40 lb-in (4.5 Nm)
10-14, 35 lb-in (4.0 Nm)
(1) 2 - 8 AWG AL
2-3: 50 lb-in (5.6 Nm)
3D VIEW FOR JM60030-1CR
4-6, 45 lb-in (5.1 Nm)
SCALE NONE
8, 40 lb-in (4.5 Nm)
-SR/PR WIRE RANGE: (1) 10-18 AWG CU ONLY
10-18 AWG = 20 LB-IN (2.3NM)
6) USE 4MM DIA. CABLE LOCK OR 1/4 INCH DIA. HASP PADLOCK.
7) RECOMMEND USING DIN-RAIL END STOPS FOR DIN RAIL MOUNTED APPLICATIONS
BUSSMANN PART NUMBERS BRKT-ND OR BRKT-NDSCREW2
8) USE BUSMANN MAKER LABEL TM26CB
9) ALL DIMENSIONS ARE TYPICAL UNLESS OTHERWISE INDICATED
8
84
3.3
56
2.2
A.VZM
QUALITY
--
DATE
5/08/2014
5/08/2014
--/--/----
MATERIAL
(0)
(0)
.
CUSTOMER PRINT
TITLE
N/A
N/A
2
600V / 30A CLASS J FUSE BLOCK
SIZE
DWG NO.
SCALE:
1:2
A3
FINISH
A
JM60030-SERIES-CP
SHEET
1
REV
A
1 OF 2
Tue Oct 01, 2013 4:0X PM GPK
8
7
6
5
4
3
2
1
F
F
CUT COVER TAB
AT NOTCH FOR
USE WITH WIRES
LARGER THAN
8 AWG
E
E
D
D
1. HOOK DIN RAIL SNAPS ON ONE SIDE OF THE DIN RAIL
2. PUSH DOWN TO DEFLECT THE SNAPS
DETAIL A
SCALE 1 : 1
C
C
A
3. ROTATE UNTIL THE
OPPOSITE SIDE SNAPS
ONTO DIN RAIL
B
B
CLOSING
PUSH STRAIGHT DOWN UNTIL SNAPS CLICK
INTO PLACE
INSTALLATION ON DIN RAIL
END STOPS MAY BE NECESSARY FOR SOME
ASSEMBLY CONDITIONS - SEE NOTE 7
OPENING
PULL STRAIGHT UP AT BOTH OUTSIDE
HANDLES
.
CUSTOMER PRINT
SLA3_BUSS_NAE_GENRL_REV_A
A
TITLE
7
6
5
4
3
2
600V / 30A CLASS J FUSE BLOCK
SIZE
DWG NO.
SCALE:
1:2
A3
8
A
JM60030-SERIES-CP
SHEET
1
REV
A
2 OF 2
Tue Oct 01, 2013 4:0X PM GPK
Download