8 CATALOG NO. F 7 TERMINAL TYPE JM70100-1CR BOX LUG JM70100-2CR BOX LUG JM70100-3CR BOX LUG 6 IP20 FINGER SAFE COVERS W/O INDICATION INDICATION 5 4 2 1 REVISIONS NO. OF POLES REV ZONE A 1 CVR-J-60060 3 DESCRIPTION DATE ECN BY PRE-RELEASE 5/8/14 BU-SB14TBD AVM 2 CVRI-J-60060 F 3 PROVISION FOR MARKER LABEL SEE NOTE 8 39 1.5 7 .3 PROVISION FOR MARKER LABEL SEE NOTE 8 76 3.0 E CVR-J-60060 (NON INDICATING) CVRI-J-60060 (WITH INDICATION) 114 4.5 E R3 .1 94 3.7 5 .2 18 .7 38 1.5 38 1.5 D 53 2.1 C PROVISION FOR MARKER LABEL SEE NOTE 8 119 4.7 113 4.5 75 3.0 LOCKOUT - TAGOUT RING SEE NOTE 6 65 2.6 18 .7 1-POLE JM70100-1CR D 2-POLE JM70100-2CR C JM70100-1CR SHOWN WITH COVER 3-POLE JM70100-3CR NOTES: B SLA3_BUSS_NAE_GENRL_REV_A A 1) VOLTAGE RATING: 600V 2) AMPERAGE: 60A 3) WITHSTAND RATING: 200kA 4) WIRE: CU/AL 75/90C 5) WIRE RANGE: (1) 2 - 14 AWG CU 2-3: 50 lb-in (5.6 Nm) 4-6, 45 lb-in (5.1 Nm) 8, 40 lb-in (4.5 Nm) 10-14, 35 lb-in (4.0 Nm) (1) 2 - 8 AWG AL 2-3: 50 lb-in (5.6 Nm) 4-6, 45 lb-in (5.1 Nm) 8, 40 lb-in (4.5 Nm) 6) USE 4mm DIA. CABLE LOCK OR 1/4" DIA. HASP PADLOCK. 7) RECOMMEND USING DIN-RAIL END STOPS FOR DIN RAIL MOUNTED APPLICATIONS BUSSMANN PART NUMBERS BRKT-ND OR BRKT-NDSCREW2 8) US BUSSMANN MARKER LABEL TM26CB 9) ALL DIMENSIONS ARE TYPICAL UNLESS OTHERWISE INDICATED B MODEL VERSION MODEL SOURCE DATA JM70100-1CR THIS DRAWING IS AN UNCONTROLLED COPY IF PRINTED OR SENT ELECTRONICALLY, DO NOT SCALE DRAWING 7 6 APPROVALS GENERAL DRAWING PRACTICES IN ACCORDANCE WITH ASME - Y14.100-2004 DIMENSIONS AND TOLERANCES IN ACCORDANCE WITH ASME - Y14.5M-1994 PRODUCT MANAGER D. McDowell ENGINEER EATON CORPORATION - CONFIDENTIAL AND PROPRIETARY UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION MILLIMETERS TOLERANCES TO BE THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTIANED THEREON, IS CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON CORPORATION AND IS MERELY ON LOAN AND SUBJECT TO RECALL BY EATON AT ANY TIME. BY TAKING POSSESSION OF THE DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF EATON AND THAT NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE PRIOR WRITTEN CONSENT OF EATON. IN THE CASE OF CONFLICTING CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT. C 2012 Eaton Corporation, All Rights Reserved. 8 3D VIEW FOR JM70100-1CR WITH COVER SCALE NONE 3D VIEW FOR JM70100-1CR SCALE NONE 5 4 ONE PLACE X.X TWO PLACE X.X X ALL ANGLES X.X = ±0.3 mm = ±0.13 mm = ± 1° SPECIAL CHARACTERISTIC SIGNIFICANT CHARACTERISTIC THIRD ANGLE PROJECTION 3 A.VZM QUALITY -- DATE 5/8/2014 5/8/2014 --/--/---- MATERIAL (0) (0) . CUSTOMER PRINT TITLE N/A N/A 2 700V / 100A 22X58 FUSE BLOCK SIZE DWG NO. SCALE: 1:2 A3 FINISH A JM70100-SERIES-CP SHEET 1 REV A 1 OF 2 Tue Oct 01, 2013 4:0X PM GPK 8 7 6 5 4 3 2 1 F F CUT COVER TAB AT NOTCH FOR USE WITH WIRES LARGER THAN 8 AWG E E 1. HOOK DIN RAIL SNAPS ON ONE SIDE OF THE DIN RAIL D D DETAIL A SCALE 1 : 1 2. PUSH DOWN TO DEFLECT THE SNAPS C C A 3. ROTATE UNTIL THE OPPOSITE SIDE SNAPS ONTO DIN RAIL B B CLOSING PUSH STRAIGHT DOWN UNTIL SNAPS CLICK INTO PLACE INSTALLATION ON DIN RAIL END STOPS MAY BE NECESSARY FOR SOME ASSEMBLY CONDITIONS - SEE NOTE 7 OPENING PULL STRAIGHT UP AT BOTH OUTSIDE HANDLES . CUSTOMER PRINT SLA3_BUSS_NAE_GENRL_REV_A A TITLE 7 6 5 4 3 2 700V / 100A 22X58 FUSE BLOCK SIZE DWG NO. SCALE: 1:2 A3 8 A JM70100-SERIES-CP SHEET 1 REV A 2 OF 2 Tue Oct 01, 2013 4:0X PM GPK