8 F 7 CATALOG NO. TERMINAL TYPE BPVM-1S SCREW BPVM-2S SCREW BPVM-1C BOX LUG BPVM-2C BOX LUG 6 5 IP20 FINGER SAFE COVERS W/O INDICATION CVR-CCM SEE NOTE 7 INDICATION CVRI-CCM SEE NOTE 7 4 3 2 1 REVISIONS NO. OF POLES REV 1 A ZONE DESCRIPTION DATE ECN BY PRE-RELEASE 5/8/14 BU-SB14TBD AVM 2 F 1 2 E CVR-CCM (NON INDICATING) CVRI-CCM (WITH INDICATION) 33 1.3 10 .4 95 3.7 D 4 .2 D 20 .8 BPVM-1C WITH COVER BPVM-1C 39 1.5 20 .8 LOCKOUT TAGOUT RING SEE NOTE 6 16 .6 33 1.3 41 1.6 C 77 3.0 #10-32 SCREW LOCKOUT TAGOUT RING SEE NOTE 6 40 1.6 21 .8 E PROVISION FOR MARKER LABEL SEE NOTE 9 C BPVM-1S SHOWN WITH COVER 2 POLE BPVM-2S SHOWN 1 POLE BPVM-1S SHOWN BPVM-1S NOTES: B SLA3_BUSS_NAE_GENRL_REV_A A 1) VOLTAGE RATING: 1000V 2) AMPERAGE: 30A 3) WITHSTAND RATING: 33kA 4) -C: WIRE RANGE: (1) CU 75/90C 2-3 AWG = 50 LB-IN (5.6NM) 4-6 AWG = 45 LB-IN (5.1NM) 8-14 AWG = 35 LB-IN (4.0 NM) (1) AL 75/90C 2-6 AWG = 50 LB-IN (5.6NM) 8 AWG = 40 LB-IN (4.5NM) 5) -S WIRE RANGE: (1) CU 75/90C 10-18 AWG = 20 LB-IN (2.3NM) 6) USE 4MM DIA. CABLE LOCK 7) CVR-CCM AND CVRI-CCM 4AWG MAX WIRE FITS WITH MOST RING AND FORK CONNECTORS 8) RECOMMEND USING DIN-RAIL END STOPS FOR DIN RAIL MOUNTED APPLICATIONS BUSSMANN PART NUMBERS BRKT-ND OR BRKT-NDSCREW2 9) USE BUSSMANN MARKER LABEL TM26CB 10) ALL DIMENSIONS ARE TYPICAL UNLESS OTHERWISE INDICATED B 3D VIEW FOR BVPM-1C WITH COVER CVRI-CCM SCALE NONE 3D VIEW FOR BPVM-1C SCALE NONE 7 6 . CUSTOMER PRINT MODEL VERSION MODEL SOURCE DATA BPVM-XS THIS DRAWING IS AN UNCONTROLLED COPY IF PRINTED OR SENT ELECTRONICALLY, DO NOT SCALE DRAWING APPROVALS GENERAL DRAWING PRACTICES IN ACCORDANCE WITH ASME - Y14.100-2004 DIMENSIONS AND TOLERANCES IN ACCORDANCE WITH ASME - Y14.5M-1994 PRODUCT MANAGER D. McDowell ENGINEER EATON CORPORATION - CONFIDENTIAL AND PROPRIETARY UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION MILLIMETERS TOLERANCES TO BE THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTIANED THEREON, IS CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON CORPORATION AND IS MERELY ON LOAN AND SUBJECT TO RECALL BY EATON AT ANY TIME. BY TAKING POSSESSION OF THE DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF EATON AND THAT NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE PRIOR WRITTEN CONSENT OF EATON. IN THE CASE OF CONFLICTING CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT. C 2012 Eaton Corporation, All Rights Reserved. 8 3D VIEW FOR BPVM-1S WITH COVER CVRI-CCM SCALE NONE 3D VIEW FOR BPVM-1S SCALE NONE 5 4 ONE PLACE X.X TWO PLACE X.X X ALL ANGLES X.X = ±0.3 mm = ±0.13 mm = ± 1° SPECIAL CHARACTERISTIC SIGNIFICANT CHARACTERISTIC THIRD ANGLE PROJECTION 3 A.VZM QUALITY -- DATE 5/08/2014 5/08/2014 --/--/---- MATERIAL (0) (0) A TITLE 1000V 30A 10X38 PV FUSE HOLDER N/A SIZE DWG NO. SCALE: 1:2 A3 FINISH N/A 2 BPVM-SERIES-CP SHEET 1 REV A 1 OF 2 Tue Oct 01, 2013 4:0X PM GPK 8 7 6 5 4 3 2 1 F F E E 1. HOOK DIN RAIL SNAPS ON ONE SIDE OF THE DIN RAIL 2. PUSH DOWN TO DEFLECT THE SNAPS D D PUSH COVER PIVOT AND END PIECE SNAPS INTO SLOTS IN BASE. THE COVER MAY BE ORIENTED IN EITHER DIRECTION. C C 3. ROTATE UNTIL THE OPPOSITE SIDE SNAPS ONTO DIN RAIL COVER INSTALLATION ONCE INSTALLED THE COVER CANNOT BE REMOVED B OPENING AND CLOSING PUSH/PULL ON END TAB, ROTATE UNTIL CLOSED/OPEN INSTALLATION ON DIN RAIL END STOPS MAY BE NECESSARY FOR SOME ASSEMBLY CONDITIONS - SEE NOTE 8 B . CUSTOMER PRINT SLA3_BUSS_NAE_GENRL_REV_A A TITLE 7 6 5 4 3 2 1000V 30A 10X38 PV FUSE HOLDER SIZE DWG NO. SCALE: 1:2 A3 8 A BPVM-SERIES-CP SHEET 1 REV A 2 OF 2 Tue Oct 01, 2013 4:0X PM GPK