Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Single-Door Free-Standing
Data Sheet
Construction
• Enclosure and door are fabricated from (12) gauge, Type
304 or Type 316L stainless steel
• All continuous welded seams are finished smooth
Application
• Doors are secured to the body with a heavy duty,
stainless steel continuous hinge on one side and easy-torelease stainless steel door clamps mounted to the other
three sides
• Houses electrical controls and instruments
• Door has a seamless poured in place gasket
• Easy access fixed or swing panels for mounting
optional equipment
• Ground stud provided on door
• Intended for indoor or outdoor use
• Print pocket provided
• Protects against corrosion, windblown dust and
rain, splashing water and hose directed water
• Large lifting eyebolts are supplied
• Each door has a padlock hasp with sealing hole provision
• Mounting channels are welded inside for locating panels
or rack mount equipment along enclosure depth
Type 4X Panel Enclosures
Standards
• A variety of optional panels and accessories are available
• UL 508 Listed, Type 4, Type 4X and Type 12
• CSA C22.2 No. 94 Certified, Type 4, Type 4X and
Type 12
• Conforms to NEMA Standard for Type 4, Type 4X
and Type 12
• E.I.A. RS-310-D
Finish
• Door and sides of body have a smooth #4 brushed
finish
Accessories
• Full and half panels
• Side and swing panels
• Channel mounting hardware
• Equipment rack mounts
• Touch-up paint
• See Accessories section
90
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Single-Door Free-Standing
Catalog Number and Illustration Sheet
Enclosure Size
Height x Width x Depth
AxBxC
Enclosure
Catalog #
D
Type 304
Type 316L
in.
mm.
in.
mm.
CH722518-4XSFS
CH722518-4XSS6FS
72.00 x 25.00 x 18.00
1829 x 635 x 457
29.12
740
CH723118-4XSFS
CH723118-4XSS6FS
72.00 x 31.00 x 18.00
1829 x 787 x 457
29.12
740
CH723718-4XSFS
CH723718-4XSS6FS
72.00 x 37.00 x 18.00
1829 x 940 x 457
29.12
740
CH722524-4XSFS
CH722524-4XSS6FS
72.00 x 25.00 x 24.00
1829 x 635 x 610
29.12
740
CH723124-4XSFS
CH723124-4XSS6FS
72.00 x 31.00 x 24.00
1829 x 787 x 610
29.12
740
CH723724-4XSFS
CH723724-4XSS6FS
72.00 x 37.00 x 24.00
1829 x 940 x 610
29.12
740
B
C
lifting eye
B-2.62
(67)
B-3.75
D
(95)
padlock hasp
CL
A
A-10.75
(273)
D
3.50
(89)
8.87
(225)
print pocket
(supplied)
7.37
CL
Type 4X Panel Enclosures
door clamp
(see note on this page)
mounting channel
(187)
Side View
Front View
Notes: Clamps are mounted along three sides of the enclosure door. Spacing between clamps along side opposite the hinge does not exceed 15 inches.
Four lifting eyes are furnished when C dimension is 24”. Dimensions are in inches. Millimeters shown are for reference only.
Data subject to change without notice.
EATON CORPORATION
May 2013
91
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Single-Door Free-Standing with Quarter-Turn Latches
Data Sheet and Catalog Number
Finish
• Door and sides of body have a smooth #4 brushed finish
Accessories
• Full and half panels
• Side and swing panels
• Panel support kit
• Panel lifting kit
• Channel mounting hardware
• Equipment rack mounts
• Lights
• Window kits
Construction
• Enclosure and doors are fabricated from (12) gauge stainless steel
Type 4X Panel Enclosures
• All continuous welded seams are finished smooth
Application
• Heavy duty stainless steel continuous hinges and pins
• Houses electrical controls and instruments
• Slotted quarter-turn flush latch(es)
• Easy access panels or rack mounts for housing
optional equipment
• Door has a seamless poured in place gasket
• Intended for indoor or outdoor use
• Ground stud provided on door
• Protects against corrosion, windblown dust and rain,
splashing water and hose directed water
• Print pocket provided
• Formed lip around enclosure opening diverts liquids and contaminants
• Mounting channels are welded inside for locating panels or rack mount
equipment along enclosure depth
Standards
• Provision for mounting fluorescent light
• UL 508 Listed, Type 3R, Type 4, Type 4X and Type 12
• Large lifting eyebolts
• CSA C22.2 No. 94 Certified, Type 3R, Type 4, Type 4X
and Type 12
• Conforms to NEMA Standard for Type 3, Type 3R,
Type 4, Type 4X and Type 12
• Meets NEMA Type 3R requirements
• E.I.A. RS-310-D
Enclosure Size
Height x Width x Depth
AxBxC
Enclosure
Catalog #
D
Type 304
in.
mm.
in.
mm.
CH722418-4XSFSQT
72.00 x 24.00 x 18.00
1829 x 609 x 457
29.12
740
CH723024-4XSFSQT
72.00 x 30.00 x 24.00
1829 x 762 x 609
29.12
740
CH723624-4XSFSQT
72.00 x 36.00 x 24.00
1829 x 914 x 609
29.12
740
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
92
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Single-Door Free-Standing with Quarter-Turn Latches
Illustration Sheet
C
B
lifting eye
B-2.62
(67)
B-3.75
D
(95)
quarter-turn
latches
CL
A
A-10.75
(273)
D
3.50
8.87
(225)
print pocket
(supplied)
CL
7.37
mounting channel
(187)
Side View
Type 4X Panel Enclosures
(89)
Front View
Notes: Four lifting eyes are furnished when C dimension is 24”.
Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
93
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Single-Door Free-Standing with 3-Point Locking
Data Sheet
Finish
• Door and sides of body have a smooth #4 brushed finish
Accessories
• Full and half panels
• Side and swing panels
• Panel support kit
• Panel lifting kit
• Channel mounting hardware
• Equipment rack mounts
• Lights
• Window kits
• Replacement handle
Construction
Application
• Enclosure and doors are fabricated from (12) gauge stainless steel
Type 4X Panel Enclosures
• Houses electrical controls and instruments
• All continuous welded seams are finished smooth
• Easy access panels or rack mounts for housing
optional equipment
• Heavy duty stainless steel continuous hinges and pins
• Intended for indoor or outdoor use
• Internal 3-point latching with stainless padlocking handles
• Protects against corrosion, windblown dust and rain,
splashing water and hose directed water
• Door has a seamless poured in place gasket
• Formed lip around enclosure opening diverts liquids and contaminants
• Ground stud provided on door
Standards
• Print pocket provided
• UL 508 Listed, Type 3R, Type 4, Type 4X and Type 12
• Mounting channels are welded inside for locating panels or rack mount
equipment along enclosure depth
• CSA C22.2 No. 94 Certified, Type 3R, Type 4, Type 4X
and Type 12
• Provision for mounting fluorescent light
• Conforms to NEMA Standard for Type 3, Type 3R,
Type 4, Type 4X and Type 12
• Large lifting eyebolts
• Meets NEMA Type 3R requirements
• E.I.A. RS-310-D
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
94
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Single-Door Free-Standing with 3-Point Locking
Illustration Sheet and Catalog Number
Enclosure Size
Height x Width x Depth
AxBxC
Enclosure
Catalog #
D
Type 304
in.
mm.
in.
mm.
CH602418-4XSFS3PT
60.00 x 24.00 x 18.00
1524 x 609 x 457
23.12
587
CH722418-4XSFS3PT
72.00 x 24.00 x 18.00
1829 x 609 x 457
29.12
739
CH723018-4XSFS3PT
72.00 x 30.00 x 18.00
1829 x 762 x 457
29.12
739
CH723618-4XSFS3PT
72.00 x 36.00 x 18.00
1829 x 914 x 457
29.12
739
CH902420-4XSFS3PT
90.00 x 24.00 x 20.00
2286 x 609 x 508
38.12
968
CH903620-4XSFS3PT
90.00 x 36.00 x 20.00
2286 x 914 x 508
38.12
968
CH603624-4XSFS3PT
60.00 x 36.00 x 24.00
1524 x 914 x 609
23.12
587
CH722424-4XSFS3PT
72.00 x 24.00 x 24.00
1829 x 609 x 609
29.12
739
CH723024-4XSFS3PT
72.00 x 30.00 x 24.00
1829 x 762 x 609
29.12
739
CH723624-4XSFS3PT
72.00 x 36.00 x 24.00
1829 x 914 x 609
29.12
739
CH903624-4XSFS3PT
90.00 x 36.00 x 24.00
2286 x 914 x 609
38.12
968
CH723630-4XSFS3PT
72.00 x 36.00 x 30.00
1829 x 914 x 762
29.12
739
CH723636-4XSFS3PT
72.00 x 36.00 x 36.00
1829 x 914 x 914
29.12
739
CH903636-4XSFS3PT
90.00 x 36.00 x 36.00
2286 x 914 x 914
38.12
968
C
B
lifting eye
B-2.62
(67)
B-3.75
D
(95)
3-point handle
rotation
A-10.75
D
(273)
Type 4X Panel Enclosures
CL
A
3.50
(89)
8.87
(225)
Front View
print pocket
(supplied)
7.37
CL
(187)
Side View
mounting channel
Notes: Four lifting eyes are furnished when C dimension is 24”. Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
95
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Single-Door Dual Access Free-Standing with 3-Point Locking
Data Sheet
Accessories
• Full and half panels
• Side and swing panels
• Panel support kit
• Panel lifting kit
• Channel mounting hardware
• Equipment rack mounts
Application
• Lights
• Houses electrical controls and instruments
• Window kits
• Easy access panels or rack mounts for housing
optional equipment
• Replacement handle
Type 4X Panel Enclosures
• Intended for indoor or outdoor use
• Protects against corrosion, windblown dust and rain,
splashing water and hose directed water
Construction
Standards
• All continuous welded seams are finished smooth
• UL 508 Listed, Type 3R, Type 4, Type 4X and Type 12
• Heavy duty stainless steel continuous hinges and pins
• CSA C22.2 No. 94 Certified, Type 3R, Type 4, Type 4X
and Type 12
• Internal 3-point latching with stainless padlocking handles
• Conforms to NEMA Standard for Type 3, Type 3R,
Type 4, Type 4X and Type 12
• Formed lip around enclosure openings to diverts liquids and
contaminants
• E.I.A. RS-310-D
• Dual-access construction available for back-to-back panel and
equipment mounting
• Meets NEMA Type 3R requirements
• Enclosure and doors are fabricated from (12) gauge stainless
steel
• Doors have a seamless poured in place gasket
• Ground studs provided on doors
• Print pockets provided
Finish
• Door and sides of body have a smooth #4 brushed finish
• Mounting channels are welded inside for locating panels or rack
mount equipment along enclosure depth
• Provisions for mounting fluorescent light
• Large lifting eyebolts
96
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Single-Door Dual-Access Free-Standing with
3-Point Locking
Illustration Sheet and Catalog Number
Enclosure Size
Height x Width x Depth
AxBxC
Enclosure
D
Catalog #
in.
mm.
in.
mm.
CH722424-4XSFSDA3PT
72.00 x 24.00 x 24.00
1829 x 609 x 609
29.12
739
CH723024-4XSFSDA3PT
72.00 x 30.00 x 24.00
1829 x 762 x 609
29.12
739
CH723624-4XSFSDA3PT
72.00 x 36.00 x 24.00
1829 x 914 x 609
29.12
739
CH903624-4XSFSDA3PT
90.00 x 36.00 x 24.00
2286 x 914 x 609
38.12
968
CH722430-4XSFSDA3PT
72.00 x 24.00 x 30.00
1829 x 609 x 762
29.12
739
CH722436-4XSFSDA3PT
72.00 x 24.00 x 36.00
1829 x 609 x 914
29.12
739
CH723636-4XSFSDA3PT
72.00 x 36.00 x 36.00
1829 x 914 x 914
29.12
739
CH903636-4XSFSDA3PT
90.00 x 36.00 x 36.00
2286 x 914 x 914
38.12
968
C
B
lifting eye
B-1.62
(41)
mounting channel
B-2.75
D
(70)
3-point handle
rotation
A
D
(273)
Type 4X Panel Enclosures
A-10.75
8.87
(225)
Side View
print pocket
(supplied)
7.37
(187)
Front View
Notes: Four lifting eyes are furnished when C dimension is 24”.
Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
97
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Double-Door Free-Standing with 3-Point Locking
Data Sheet
Finish
• Doors and sides of body have a smooth #4 brushed finish
Accessories
• Full and half panels
• Side and swing panels
• Panel support kit
• Panel lifting kit
• Channel mounting hardware
• Equipment rack mounts
• Lights
• Window kits
• Replacement handle
Construction
• Enclosure and doors are fabricated from (12) gauge stainless
steel
Application
• All continuous welded seams are finished smooth
• Houses electrical controls and instruments
• Heavy duty stainless steel continuous hinges and pins
• Easy access panels or rack mounts for housing
optional equipment
• Internal 3-point latching with stainless padlocking handles
• Doors have a seamless poured in place gasket
• Intended for indoor or outdoor use
• Formed lip around enclosure openings to diverts liquids and
contaminants
Type 4X Panel Enclosures
• Protects against corrosion, windblown dust and rain,
splashing water and hose directed water
• Ground studs provided on doors
• Removable center post for easy panel installation
Standards
• Print pockets provided
• UL 508 Listed, Type 3R, Type 4, Type 4X and Type 12
• Mounting channels are welded inside for locating panels or
rack mount equipment along enclosure depth
• CSA C22.2 No. 94 Certified, Type 3R, Type 4, Type 4X
and Type 12
• Provisions for mounting fluorescent light
• Conforms to NEMA Standard for Type 3, Type 3R,
Type 4 and Type 4X, Type 12
• Large lifting eyebolts
• Meets NEMA Type 3R requirements
• E.I.A. RS-310-D
98
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Double-Door Free-Standing with 3-Point Locking
Illustration Sheet and Catalog Number
Enclosure Size
Height x Width x Depth
AxBxC
Enclosure
D
Catalog #
in.
mm.
in.
mm.
CH604818-4XSFSD3PT
60.00 x 48.00 x 18.00
1524 x 1219 x 457
23.12
587
CH724818-4XSFSD3PT
72.00 x 48.00 x 18.00
1829 x 1219 x 457
29.12
739
CH726018-4XSFSD3PT
72.00 x 60.00 x 18.00
1829 x 1524 x 457
29.12
739
CH727218-4XSFSD3PT
72.00 x 72.00 x 18.00
1829 x 1829 x 457
29.12
739
CH904820-4XSFSD3PT
90.00 x 48.00 x 20.00
2286 x 1219 x 508
38.12
968
CH907220-4XSFSD3PT
90.00 x 72.00 x 20.00
2286 x 1829 x 508
38.12
968
CH724824-4XSFSD3PT
72.00 x 48.00 x 24.00
1829 x 1219 x 609
29.12
739
CH726024-4XSFSD3PT
72.00 x 60.00 x 24.00
1829 x 1524 x 609
29.12
739
CH727224-4XSFSD3PT
72.00 x 72.00 x 24.00
1829 x 1829 x 609
29.12
739
CH907224-4XSFSD3PT
90.00 x 72.00 x 24.00
2286 x 1829 x 609
38.12
968
CH726036-4XSFSD3PT
72.00 x 60.00 x 36.00
1829 x 1524 x 914
29.12
739
CH907236-4XSFSD3PT
90.00 x 72.00 x 36.00
2286 x 1829 x 914
38.12
968
B
C
lifting eye
B-1.62
(41)
B-2.75
mounting channel
D
(70)
body stiffener
(see note)
3-point handle
A-10.75
A
A-1.62
(41)
D
Type 4X Panel Enclosures
rotation
(273)
8.87
(225)
7.37
(187)
CL
print pocket (supplied)
Side View
Front View
Notes: Four lifting eyes are furnished when C dimension is 24”.
Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
99
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Double-Door Dual Access Free-Standing with 3-Point Locking
Data Sheet
Finish
• Doors and sides of body have a smooth #4 brushed finish
Accessories
• Full and half panels
• Side and swing panels
• Panel support kit
• Panel lifting kit
• Channel mounting hardware
• Equipment rack mounts
• Lights
• Window kits
• Replacement handle
Construction
Application
• Enclosure and doors are fabricated from (12) gauge
stainless steel
Type 4X Panel Enclosures
• Houses electrical controls and instruments
• Easy access panels or rack mounts for housing optional
equipment
• All continuous welded seams are finished smooth
• Intended for indoor or outdoor use
• Internal 3-point latching with stainless padlock handles
• Protects against corrosion, windblown dust and rain,
splashing water and hose directed water
• Doors have a seamless poured in place gasket
• Heavy duty stainless steel continuous hinges and pins
• Formed lip around enclosure openings to diverts liquids
and contaminants
Standards
• Ground studs provided on doors
• UL 508 Listed, Type 3R, Type 4, Type 4X and Type 12
• Removable center post for easy panel installation
• CSA C22.2 No. 94 Certified, Type 3R, Type 4, Type 4X and
Type 12
• Dual-access construction available for back-to-back panel
and equipment mounting
• Conforms to NEMA Standard for Type 3R, Type 4, Type 4X
and Type 12
• Print pockets provided
• Meets NEMA Type 3R requirements
• Mounting channels are welded inside for locating panels
or rack mount equipment along enclosure depth
• E.I.A. RS-310-D
• Provisions for mounting fluorescent light
• Large lifting eyebolts
100
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Ground-Mount Enclosures
Type 4X Double-Door Dual-Access Free-Standing with
3-Point Locking
Illustration Sheet and Catalog Number
Enclosure Size
Height x Width x Depth
AxBxC
Enclosure
D
Catalog #
in.
mm.
in.
mm.
CH724824-4XSFSDDA3PT
72.00 x 48.00 x 24.00
1829 x 1219 x 609
29.12
739
CH726024-4XSFSDDA3PT
72.00 x 60.00 x 24.00
1829 x 1524 x 609
29.12
739
CH727224-4XSFSDDA3PT
72.00 x 72.00 x 24.00
1829 x 1829 x 609
29.12
739
CH907224-4XSFSDDA3PT
90.00 x 72.00 x 24.00
2286 x 1829 x 609
38.12
968
CH726036-4XSFSDDA3PT
72.00 x 60.00 x 36.00
1829 x 1524 x 914
29.12
739
C
B
lifting eye
B-1.62
(41)
B-2.75
(70)
mounting
channel
D
3-point
handle
A-10.75
(273)
rotation
A-1.62
(41)
D
Type 4X Panel Enclosures
A
8.87
(225)
7.37
(187)
CL
print pocket (supplied)
Side View
Front View
Notes: Four lifting eyes are furnished when C dimension is 24”.
Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
101
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Type 4X Single-Door
Full and Half Panel
Illustration Sheet and Catalog Number
Full Panel (Single-Door)
Panel Size
Panel
Fits Enclosure
Height x Width
C
Height x Width
AxB
Half Panel (Single-Door)
Panel Size
Panel
Fits Enclosure
Height x Width
C
Height x Width
AxB
Catalog #
in.
mm.
in.
mm.
in.
mm.
Catalog #
in.
mm.
in.
mm.
in.
mm.
CHAF6024P
47.87 x 19.87
1216 x 505
23.12
587
60.00 x 24.00
1524 x 610
CHAF6024HP
24.75 x 19.87
629 x 505
23.12
587
60.00 x 24.00
1524 x 610
CHAF6036P
47.87 x 31.87
1216 x 809
23.12
587
60.00 x 36.00
1524 x 914
CHAF6036HP
24.75 x 31.87
629 x 809
23.12
587
60.00 x 36.00
1524 x 914
CHAF7224P
59.87 x 19.87
1521 x 505
29.12
740
72.00 x 24.00
1829 x 610
CHAF7224HP
30.75 x 19.87
781 x 505
29.12
587
72.00 x 24.00
1829 x 610
CHAF7230P
59.87 x 25.87
1521 x 657
29.12
740
72.00 x 30.00
1829 x 762
CHAF7230HP
30.75 x 25.87
781 x 657
29.12
587
72.00 x 30.00
1829 x 762
CHAF7236P
59.87 x 31.87
1521 x 809
29.12
740
72.00 x 36.00
1829 x 914
CHAF7236HP
30.75 x 31.87
781 x 809
29.12
587
72.00 x 36.00
1829 x 914
CHAF9024P
77.87 x 19.87
1978 x 505
38.12
968
90.00 x 24.00
2286 x 610
CHAF9024HP
39.75 x 19.87
1010 x 505
38.12
968
90.00 x 24.00
2286 x 610
CHAF9036P
77.87 x 31.87
1978 x 809
38.12
968
90.00 x 36.00
2286 x 914
CHAF9036HP
39.75 x 31.87
1010 x 809
38.12
968
90.00 x 36.00
2286 x 914
B
B-1.62
(41)
B
B-1.62
(41)
panel
side bracket
included
(see illustration #1 page
110 and detail
sheet page
111)
C
A-1.62
(41)
Type 4X Panel Enclosures
A
C A
Half Panel
(upper mount)
C
Full Panel
C A
Half Panel
(lower mount)
Full Panel Mounting
Half Panel Mounting
Note: Full and half panel for single-door, single and dual-access enclosures are (12) gauge steel and furnished with panel
side brackets and all hardware necessary for channel and panel mounting. Half panels can be mounted in either
the upper or lower portion of the enclosure. Free-standing design permits the panel to adjust along the depth of the
enclosure. With dual-access enclosures, full and half panels can be mounted back-to-back.
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
104
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Type 4X Double-Door
Full Panel
Illustration Sheet and Catalog Number
Panel Size
Panel
C
Height x Width
AxB
Fits Enclosure
Height x Width
D
Catalog #
in.
mm.
in.
mm.
in.
mm.
in.
mm.
CHAF6048P
47.87 x 43.87
1216 x 1114
23.12
587
21.12
530
60.00 x 48.00
1524 x 1219
CHAF6060P
47.87 x 55.87
1216 x 1419
23.12
587
27.12
689
60.00 x 60.00
1524 x 1524
CHAF7248P
59.87 x 43.87
1521 x 1114
29.12
740
21.12
530
72.00 x 48.00
1829 x 1219
CHAF7260P
59.87 x 55.87
1521 x 1419
29.12
740
27.12
689
72.00 x 60.00
1829 x 1524
CHAF7272P
59.87 x 67.87
1521 x 1724
29.12
740
33.12
841
72.00 x 72.00
1829 x 1829
CHAF9048P
77.87 x 43.87
1978 x 1114
38.12
968
21.12
530
90.00 x 48.00
2286 x 1219
CHAF9072P
77.87 x 67.87
1978 x 1724
38.12
968
33.12
841
90.00 x 72.00
2286 x 1829
B
B-1.62
(41)
D
D
panel side bracket included
(see illustration #1 page 110
and detail sheet page 111)
C
A
A-1.62
(41)
Type 4X Panel Enclosures
C
Full Panel
center post included with
double-door full panel
(see illustration #5 page 110)
Full Panel Mounting
Notes: Full panel for double-door, single and dual-access enclosures are (10) gauge steel and furnished with
panel brackets, center post assembly, panel handle kit and all hardware necessary for channel and panel
mounting. The center post assembly offers additional support of panel and equipment. Free-standing design
permits the panel to adjust along the depth of the enclosure. With dual-access enclosures, full and half
panels can be mounted back-to-back.
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
105
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Type 4X Double-Door, Half Panel
Illustration Sheet and Catalog Number
Panel Size
Panel
C
Height x Width
AxB
Fits Enclosure
Height x Width
D
Catalog #
in.
mm.
in.
mm.
in.
mm.
in.
mm.
CHAF6048HP
24.75 x 43.87
629 x 1114
23.12
587
21.12
536
60.00 x 48.00
1524 x 1219
CHAF7248HP
30.75 x 43.87
781 x 1114
29.12
740
21.12
536
72.00 x 48.00
1829 x 1219
CHAF7260HP
30.75 x 55.87
781 x 1419
29.12
740
7.12
181
72.00 x 60.00
1829 x 1524
CHAF7272HP
30.75 x 67.87
781 x 1724
29.12
740
33.12
841
72.00 x 72.00
1829 x 1829
CHAF9048HP
39.75 x 43.87
1010 x 1114
38.12
968
21.12
536
90.00 x 48.00
2286 x 1219
CHAF9072HP
39.85 x 67.87
1012 x 1724
38.12
968
33.12
841
90.00 x 72.00
2286 x 1829
B
B-1.62
(41)
D
D
panel side bracket included
(see illustration #1 page 110
and detail sheet page 111)
A C
Type 4X Panel Enclosures
Half Panel
(upper mount)
A C
Half Panel
(lower mount)
center post or double-door
panel support bracket
(sold separately)
(see illustration #5 page 110)
Half Panel Mounting
Note:
Half panel for double-door, single and dual-access enclosures are (12) gauge steel and furnished with panel brackets and all
hardware necessary for channel and panel mounting. A center post assembly or a double-door panel support bracket (catalog
number CHAFSUP2) for additional support of the panel is optional and sold separately. Free-standing design permits the panel
to adjust along the depth of the enclosure. With dual-access enclosures, full and half panels can be mounted back-to-back.
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
106
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Type 4X, Side Panel and Center Post
Illustration Sheet and Catalog Number
Panel Size
Panel
C
Height x Width
AxB
Center
Post
Fits Enclosure
A
Fits
Enclosure
B
Height
Catalog #
in.
mm.
in.
mm.
in.
mm.
in.
mm.
Catalog #
in.
mm.
in.
mm.
in.
mm.
CHAF6018SP
48.37 x 13.87
1229 x 340
23.12
587
60.00
1524
18.00
457
CHAF60CPS
58.37
1483
23.12
587
60.00
1524
CHAF7218SP
60.37 x 13.87
1533 x 340
29.12
740
72.00
1829
18.00
457
CHAF72CPS
70.37
1787
29.12
740
72.00
1829
CHAF7224SP
60.37 x 19.87
1533 x 505
29.12
740
72.00
1829
24.00
610
CHAF90CPS
88.37
2245
38.12
968
90.00
2286
CHAF9018SP
78.37 x 13.87
1991 x 340
38.12
968
90.00
2286
18.00
457
CHAF9024SP
78.37 x 19.87
1991 x 505
38.12
968
90.00
2286
24.00
457
* Back panels restrict the movement of side panels and will prohibit
mounting in some depths. See detail sheet for back panel spacing.
B
B-1.62
(41)
C
B
A
A
A-2.12
(54)
B
Side Panel
Side Panel Mounting
Center Post Assembly
Side panels are (12) gauge steel and furnished with
hardware necessary for channel mounting. They will
fit any width enclosure and are adjustable along its
depth, however, when full or half panels are installed,
movement will be restricted and with some depths
make side mounting prohibitive.
Center post assembly is furnished with all double-door full
panels and includes hardware necessary for channel and
panel mounting. The center post is optional on double-door
half panels and swing panel mounting and must be ordered
separately. It attaches to the top and bottom channels making
it adjustable along the depth of the enclosure. See illustration
#5 on the Detail Sheet on page 110.
Type 4X Panel Enclosures
C
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
107
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Type 4X Single-Door, Full and Half Swing Panel
Illustration Sheet and Catalog Number
Full Swing Panel (Single Door)
Panel Size
Panel
Half Swing Panel (Single Door)
Panel Size
Fits Enclosure
C
Height x Width
AxB
Height x Width
Panel
Fits Enclosure
C
Height x Width
AxB
Height x Width
Catalog #
in.
mm.
in.
mm.
in.
mm.
Catalog #
in.
mm.
in.
mm.
in.
mm.
CHAF6024SWP
47.87 x 18.75
1216 x 476
23.12
587
60.00 x 24.00
1524 x 610
CHAF6024HSWP
24.75 x 18.75
629 x 476
23.12
587
60.00 x 24.00
1524 x 610
CHAF6036SWP
47.87 x 30.75
1216 x 781
23.12
587
60.00 x 36.00
1524 x 914
CHAF6036HSWP
24.75 x 30.75
629 x 781
23.12
587
60.00 x 36.00
1524 x 914
CHAF7224SWP
59.87 x 18.75
1521 x 476
29.12
740
72.00 x 24.00
1829 x 610
CHAF7224HSWP
30.75 x 18.75
781 x 476
29.12
740
72.00 x 24.00
1829 x 610
CHAF7230SWP
59.87 x 24.75
1521 x 629
29.12
740
72.00 x 30.00
1829 x 762
CHAF7230HSWP
30.75 x 24.75
781 x 629
29.12
740
72.00 x 30.00
1829 x 762
CHAF7236SWP
59.87 x 30.75
1521 x 781
29.12
740
72.00 x 36.00
1829 x 914
CHAF7236HSWP
30.75 x 30.75
781 x 781
29.12
740
72.00 x 36.00
1829 x 914
CHAF9024SWP
77.87 x 18.75
1978 x 476
38.12
968
90.00 x 24.00
2286 x 610
CHAF9024HSWP
39.75 x 18.75
1010 x 476
38.12
968
90.00 x 24.00
2286 x 610
CHAF9036SWP
77.87 x 30.75
1978 x 781
38.12
968
90.00 x 36.00
2286 x 914
CHAF9036HSWP
39.75 x 30.75
1010 x 781
38.12
968
90.00 x 36.00
2286 x 914
3.18
B
(81)
3.18
2.06
(52)
2.06
B
(81)
(52)
hinge
C A
swing panel
bracket assembly
included (See detail
sheet page 112)
C
Half Swing Panel
(upper mount)
A
Type 4X Panel Enclosures
hinge
C
Full Swing Panel
panel side bracket
included
(see illustration
#1 page 110 and
detail sheet page
112)
C
A
Half Swing Panel
(lower mount)
Full Swing Panel Mounting
Note:
108
hinge
Half Swing Panel Mounting
Full swing panel and half swing panel for single-door, single and dual-access enclosures are (12) gauge steel,
have a dual hinge swing panel bracket and furnished with panel brackets and all hardware necessary for channel
and panel mounting. Panels can be installed so they hinge on either the left or right side. In addition, half panels
can be mounted in either the upper or lower portion of the enclosure. Free-standing design permits the panel to
be adjustable along the depth of the enclosure. The dual hinge will allow the inner panel to swing completely out
of the door opening when within 5.50 inches of the front. With dual-access enclosures, full and half swing panels
can be mounted back-to-back.
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Type 4X Double-Door, Full and Half Swing Panel
Illustration Sheet and Catalog Number
Full Swing Panel (Single-Door)
Panel Size
Panel
Half Swing Panel (Single-Door)
Panel Size
Fits Enclosure
C
Height x Width
AxB
Height x Width
Panel
Fits Enclosure
C
Height x Width
AxB
Height x Width
Catalog #
in.
mm
in.
mm
in.
mm
Catalog #
in.
mm
in.
mm
in.
mm
CHAF6024SWP
47.87 x 18.75
1216 x 476
23.12
587
60.00 x 48.00
1524 x 1219
CHAF6024HSWP
24.75 x 18.75
629 x 476
23.12
587
60.00 x 48.00
1524 x 1219
CHAF7224SWP
59.87 x 18.75
1521 x 476
29.12
740
72.00 x 48.00
1829 x 1219
CHAF7224HSWP
30.75 x 18.75
781 x 476
29.12
740
72.00 x 48.00
1829 x 1219
CHAF7230SWP
59.87 x 24.75
1521 x 629
29.12
740
72.00 x 60.00
1829 x 1524
CHAF7230HSWP
30.75 x 24.75
781 x 629
29.12
740
72.00 x 60.00
1829 x 1524
CHAF7236SWP
59.87 x 30.75
1521 x 781
29.12
740
72.00 x 72.00
1829 x 1829
CHAF7236HSWP
30.75 x 30.75
781 x 781
29.12
740
72.00 x 72.00
1829 x 1829
CHAF9024SWP
77.87 x 18.75
1978 x 781
38.12
968
90.00 x 48.00
2286 x 1219
CHAF9024HSWP
39.75 x 18.75
1010 x 476
38.12
968
90.00 x 48.00
2286 x 1219
CHAF9036SWP
77.87 x 30.75
1978 x 781
38.12
968
90.00 x 72.00
2286 x 1829
CHAF9036HSWP
39.75 x 30.75
1010 x 781
38.12
968
90.00 x 72.00
2286 x 1829
A Center post assembly and center bracket must be ordered separately.
3.18
3.18
B
B
(81)
(81)
panel mounting
center bracket
(sold separately)
(see illustration
#2 page 110)
C
A
hinge
hinge
C
Full Swing Panel
Half Swing Panel
(lower mount)
center post and panel
mounting center bracket
(sold separately)
(see illustration #2 and #5
page 110)
Swing Panel Mounting
Note:
Type 4X Panel Enclosures
swing panel
bracket assembly
included (see detail
sheet page 112)
Full swing panel and half swing panel for double-door, single and dual-access enclosures are (12) gauge steel, have a dual hinge swing
panel bracket, and furnished with hardware necessary for side channel mounting. A center post assembly and center bracket must
be ordered separately. Panels can be installed so they hinge either on the left or right side. In addition, half panels can be mounted in
either the upper or lower portion of the enclosure. Free-standing design permits the panel to adjust along the depth of the enclosure.
The dual hinge will allow the inner panel to swing completely out of the door opening when within 5.50 inches of the front. With dualaccess enclosures, full and half swing panels can be mounted back-to-back.
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
109
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Type 4X
Miscellaneous Accessories
Illustration Sheet and Catalog Number
Miscellaneous Accessories
Catalog #
Description
Illustration
Quantity
CHAFSBRKT1
Panel mounting side bracket
1
1
CHAFCBRKT3
Panel mounting center bracket
2
3
CHAFCMH3
Channel mounting hardware
3
3
CHAFPSUP2
Double-door panel support bracket
4
2
See page 107
Center post assembly
5
1
center bracket
channel
spring nut
bracket
mounting
hardware
side bracket
panel
nut
panel nut
channel
mounting
hardware
panel mounting
stud
bracket
mounting
hardware
panel mounting
stud
Illustration 2
Illustration 1
channel
spring nut
center post
channel
mounting
hardware
panel bolt
hardware
Type 4X Panel Enclosures
Illustration 3
panel bolt
panel bolt
panel bolt
hardware
center post
panel nut
channel
mounting
hardware
install panel
bolt in this hole
for top of panel
support
center post
panel mounting stud
panel
support
bracket
panel nut
bracket
mounting
hardware
panel nut
channel
mounting
hardware
bracket
mounting
hardware
channel
spring nut
post bracket
channel spring nut
Illustration 5
Illustration 4
See catalog page 107
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
110
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Free-Standing Enclosure Details
Type 4X
Panel and Enclosure
Detail Sheet
enclosure width -5.75
(146)
2.87 min
(73)
3.00 min
(76)
2.87
Single Door
(73)
(section view showing full panels mounted back-to-back)
1/2
enclosure width -5.75
Type 4X Panel Enclosures
(146)
2.87 min
(73)
3.75 min
(95)
2.87
(73)
CL
(of enclosure)
Double Door
(section view showing full panels mounted back-to-back)
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
111
Type 4X Panel Enclosures
Free-Standing Enclosure Details
Type 4X
Swing Panel and Enclosure
Detail Sheet
2.87
enclosure width -6.06
(73)
(154)
2.87 min
(73)
5.00 min
(127)
3.18
(81)
Single Door
(section view showing swing panels mounted back-to-back)
1/2 enclosure
3.18
width -6.06
(154)
Type 4X Panel Enclosures
(81)
2.87 min
(73)
5.00 min
(127)
2.87
(73)
Double Door
(section view showing swing panels mounted back-to-back)
CL
(of enclosure)
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
112
EATON CORPORATION
May 2013
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Rack Mounting Angles
Illustration Sheet and Catalog Number
Heavy duty rack mounting angles are designed for mounting 19” (482mm) equipment in free-standing enclosures. A center post
assembly, “CHAFxxCPS”, on page 107, and a panel mounting center bracket, “CHAFCBRKT3”, on page 110, (each sold
separately) are required when mounting in any double door enclosure. Mounting holes are spaced at the 19” “EIA” standard
and are provided to accept #10-32, #12-24, or M6 cage nuts (sold in packages of 100), on page 114.
‘L’ Shaped Mounting Angles
Equipment Mounting Holes
to Accept #10-32, #12-24, or
M6 Cage Nuts
(Sold Separately)
Mounting
Angles
Note: L-shaped angles are universal
and can be rotated to accommodate
19” or 23” EIA mounting equipment.
L
1.50
(38)
Fits Enclosure
L
Height
Mounting
U’s
Catalog #
in.
mm
in.
mm
CHES-48RMA-L
48.00
1219
42.00
1067
24
CHES-60RMA-L
60.00
1524
54.25
1378
31
CHES-72RMA-L
72.00
1829
66.50
1689
38
CHES-90RMA-L
90.00
2286
78.75
2000
45
Kit contains two (2) full length ‘L’ angles, installation instructions
and hardware necessary to mount in single-door enclosures.
Yellow Zinc finish.
A
B
3.50
C
B
A = 1.75 (44)
B = .625 (16)
C = .500 (13)
D = .295 (7)
E = .250 (6)
E
(89)
D
Angle Profile
Equipment Mounting
Holes
to Accept #10-32,
#12-24, or M6
Cage Nuts
(Sold Separately)
Hole Pattern
.375 (9)
Square
Hole
‘U’ Shaped Mounting Angles
L
Fits Enclosure
L
Height
Mounting
U’s
Catalog #
in.
mm
in.
mm
CHES-48RMA-U
48.00
1219
42.00
1067
24
CHES-60RMA-U
60.00
1524
54.25
1378
31
CHES-72RMA-U
72.00
1829
66.50
1689
38
CHES-90RMA-U
90.00
2286
78.75
2000
45
Kit contains two (2) full length ‘U’ angles, installation instructions
and hardware necessary to mount in single-door enclosures.
Yellow Zinc finish.
Type 4X Panel Enclosures
Mounting
Angles
2.29
.75
(58)
(19)
A
B
1.50
1.44
(36)
(38)
O.D.
O.D.
C
B
D
1.625
(41)
O.D.
Angle Profile
E
Hole Pattern
A = 1.75 (44)
B = .625 (16)
C = .500 (13)
D = .295 (7)
E = .250 (6)
.375 (9)
Square
Hole
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
113
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Frames & Fasteners
Illustration Sheet and Catalog Number
Swing-Out Rack Mounted Frame
Mounting
Angles
Fits Enclosure
L
Height
Catalog #
in.
mm
in.
CHES-48SORMF
48.00
1219
36.91
937
CHES-60SORMF
60.00
1524
49.16
1248
CHES-72SORMF
72.00
1829
59.66
1515
CHES-90SORMF
90.00
2286
77.18
1960
Equipment
Mounting Holes
to Accept #10-32,
#12-24, or M6
Cage Nuts
(Sold Separately See Below)
mm
Heavy duty swing-out rack mounting frames are designed for mounting 19” (482mm)
equipment in free-standing enclosures. A center post assembly, “CHAFxxCPS”,
on page 107 and panel mounting center bracket, “CHAFCBRKT3”, on page 110,
(each sold separately) are required when mounting in any double door enclosure.
Mounting holes are spaced per the “EIA” standard and are provided to accept #10-32,
#12-24 or M6 cage nuts (sold in packages of 100). Swing-out rack mounting frames
have white powder coated finish.
A
B
C
B
D
L
Hole Pattern
Type 4X Panel Enclosures
A = 1.75 (44)
B = .625 (16)
C = .500 (13)
D = .295 (7)
E = .250 (6)
19.47
(494)
O.D.
Catalog #
Screw Type
CHE2-MA-1032-PHMS-100
#10-32 Phillips
CHE2-MA-1224-PHMS-100
#12-24 Phillips
CHE2-MA-M6-PHMS-100
M6 Phillips
Catalog #
Cage Nut Type
CHE2-MA-CN-1032-100
#10-32 Tapped
CHE2-MA-CN-1224-100
#12-24 Tapped
CHE2-MA-CN-M6-100
M6 Tapped
Sold in bags of 100.
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
114
E
EATON CORPORATION
May 2013
.375 (9)
Square
Hole
Type 4X Panel Enclosures
Free-Standing Enclosure Accessories
Floor Stand & Enclosure Stabilizer Kits
Illustration Sheet and Catalog Number
Floor stand kits are intended for
use with EnviroShield™ Type 4X,
Type 4 and Type 12 enclosures
where floor support is required.
Each kit consists of two (10)
gauge legs and hardware for
mounting. At the base of each
leg is a pre-punched plate (see
drawing). Steel kits have a gray
polyester powder paint finish.
Stainless steel kits are fabricated
from 304 stainless steel. Standard
floor stand kits are 12 inches (305
mm) high. For special heights,
special material or non-standard
construction, consult factory.
Catalog #
A
B
C
Steel
Stainless
in.
mm.
in.
mm.
in.
mm.
CHMFK12
CHMFK12XS
12.00
305
10.06
256
-
-
CHMFK16
CHMFK16XS
16.00
406
14.06
357
-
-
CHMFK20
CHMFK20XS
20.00
508
18.06
459
8.00
203
CHMFK24
CHMFK24XS
24.00
610
22.06
560
10.00
254
CL
Catalog #
Description
CHES-SMFK6
Set of four (4) legs
.75
(19)
Kit allows space between enclosure
and floor for compliance in NSF
environments 1-3/4” (44mm)
adjustment provides flexibility in all
applications. Four (4) legs per kit,
maintains UL/cUL Type 4X rating
when properly installed.
Type 4X Panel Enclosures
Sanitary Leg Kit
Hex Nut
Flat Washer
6.00
Sealing
Washer
(152)
.75
(19)
Leg Sleeve
1.75
(44)
Adjustment
Notes: Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice.
EATON CORPORATION
May 2013
115