The World Leader in High-Performance
High Performance Signal Processing Solutions
iSensor
®
ADIS16209 Evaluation Tool Overview
Mark Looney
Application Engineer
October 6, 2009
iSensor®
iSensor® The Simple Solution for Sensor Integration
Evaluation Tool Overview
1.
2.
2
Evaluation/Interface Board (ADIS16209/PCBZ) for simpler
connection to an existing processor/system PCB.

These boards provide a simple connector translation that
enables user to bypass LGA soldering. The 2mm pitch
connectors are easy to interface with 1mm ribbon cable or
solder to.

Part number for ordering: ADIS16209/PCBZ
Evaluation System (ADISUSBZ) for those that prefer a
simple PC interface

This system provides a simple USB interface, along with a
simple Graphical User Interface (GUI) package, for
evaluating most of the ADIS16209 functions and
performance.

Supports approximately 150-200SPS sample rate.

This system is not a development kit that comes with PC
development tools, source code and software support.

Part number for ordering: ADISUSBZ
ADIS16209/PCBZ
ADISUSBZ
iSensor® The Simple Solution for Sensor Integration
1.100
Hooking up to the ADIS16209/PCBZ
1.050
J1 Ribbon Cable Interface Parts
a
2 × 0.925
J2
J1
U1
2 × 0.673
iSensor
4 × Ø0.087
M2×0.4
C1
2 × 0.000
Ribbon Connector
3M P/N 152212-0100-GB
07980-017
2 × 0.900
0.865
0.035
2 × 0.000
0.200
0.150
Master Processor Connection
Ribbon Cable
3M P/N 3625/12 (100m)
J1
1
2
3
4
5
6
Ground
7
8
Ground
+3.3V
9
10
11
12
+5V or Reset
SS (Slave select)
3
SCLK (Serial clock)
MISO (Master In, Slave Out)
MOSI (Master Out, Slave In)
Ground
+3.3V
+3.3V
ADISUSBZ uses the following
cable assembly from Samtec:
ASP-140062-01
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Software Installation
The ADIS16209 demonstration software can be found at
www.analog.com/isensor-evaluation
1. Click on “Evaluation Software Downloads”
2. Click on 209ES.zip and save it to a temporary directory
3. Open it and double click on setup.exe.
4
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Software Installation
Installation Steps (continued)
4. Click OK on next screen
5. Click here to start installation
5
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Software Installation
Installation Steps (continued)
6. Click Continue
7. If this message comes up,
click on “No”
8. Click OK
6
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Software Installation
Installation Steps (continued)
9. Open the newly created directory and double-click onto “giveio.exe”
10. Click “Install,” then “ I Agree”
7
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Software Installation
Installation Steps (continued)
11. Click “yes”
12. Giveio Driver complete
8
iSensor® The Simple Solution for Sensor Integration
ADIS16209/PCBZ Installation on ADISUSBZ
Installation Steps (continued)
1. Secure
209/PCBZ with
2mm screws
13. Install 209/PCBZ on ADISUSBZ
14. Plug in USB cable
2. Connect
ribbon cable
3. Verify JP1
set to +3.3V
4. Hook USB
cable up
9
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Software Installation
Installation Steps (continued)
15. USB Driver screen will pop-up
Click “Next” to start this process
16. Then click on
“Continue Anyway”
This process will repeat for a second driver file.
Just follow the instructions and allow it to go
through one more time. After completing this, then
the devices is ready for test.
10
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Tips – Verify USB Driver
#1 Click here
to access
setup
#2 Click OK
to verify
#3 Click Read to see
if #’s are close to “0”
when board is laying
flat on a table
11
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Tips – Horizontal Calibration
1.Use a set of business cards to
prop up one side of the
evaluation system and simulate a
system-level offset bias.
2.Click on Read to observe the
incline angle measurement.
KEY POINTS
• Many users will experience
offset due to system-level
influences, such as PCB
thickness variation and
solder volume tolerances,
etc.
• The ADIS16209’s auto-null
provides a simple means to
overcome these offset
factors.
12
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Tips – Horizontal Calibration
1
2
3
1. Click on Calibration to open
Calibration Register Window
2. Click on auto-null, and the
part calculates the
appropriate adjustment
factors
3. Click Write, then Close, then
Read to observe the
improved behavior
13
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Tips – Horizontal Calibration
Success!
14
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Tips – Vertical Positions (0°)
15
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Tips – Vertical Positions (-90°)
16
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Tips – Vertical Positions (180°)
17
iSensor® The Simple Solution for Sensor Integration
ADIS16209 Demonstration Tips – Vertical Positions (90°)
18
 CONTACTS:
 MARKETING:
Bob Scannell, 1-336-605-4031
 APPLICATIONS ENGINEER: Mark Looney, 1-336-605-4139
MORE INFORMATION:


www.analog.com/isensor
New Brochure: iSensor Motion Sensor Products

19
BR067755-2.5-4/08(A)