For ConTech Lighting LPL and LPU LED Lighting Series Junction...

advertisement
For ConTech Lighting LPL and LPU LED Lighting Series Junction Box: LPAJB
This Direct Wire Junction Box is to be used only with LED Dimmable Under Cabinet Lighting and LED strips. This Junction Box is designed to be
wired using Non-Metallic Cable (NM) or Armored Cable (BX) supply wire.
INSTALLATION PROCEDURES
1. Turn off power for appropriate electrical circuit at electrical service panel.
2. Remove Junction Box cover screws and remove cover. Save screws and lockwashers.
3. Prepare Flat Non-Metallic Cable (NM) (2C+Ground) or Armored Cable (BX) by stripping conductor ends approximately 3/8".
4. For installation using 3/8" Miniature Die-Cast Electrical Connector (Supplied with Junction box): Determine mounting orientation and remove
one KNOCKOUT on desired side of Junction Box for electrical supply and attach 3/8" Miniature Die-Cast Electrical Connector to Junction
Box as shown. Affix 3/8" Miniature Die-Cast Electrical Connector to electrical supply (BX or NM). NM cable outer jacket must protude
through 3/8" Miniature Die-Cast Electrical Connector to adequately protect internal conductors.
5. Tighten locknut and clamping screw(s) on electrical connector fitting securely
6. Push stripped ends of wires into hole in PUSH- IN WIRE CONNECTORS (see WIRING DIAGRAM.) Supply wires are typically color-coded:
Hot-black, Neutral-white, Ground-green or bare copper. Note that black supply wire goes into Connector with black wire and white goes into
connector with white wire.green goes into green wire.
7. Push excess electrical supply wire back into wall and locate Junction Box on mounting sur face. Affix Junction Box to underside of cabinet
with captive screws provided. Be careful not to drive screws all the way though the cabinet bottom. Use shorter screws If necessary.
8. Replace and secure wiring Junction Box cover with supplied screws. Make certain lockwashers are located beneath screw heads to
properly ground cover.
9. Follow installation instructions provided with undercabinet light fixture. Mount fixture, and insert jumper cable (sold separately) or direct
end-to-end connector (supplied with fixture) into appropriate electrical port of direct wire junction box
10. Make sure that all fixtures connected to Junction Box are properly installed and that all open electrical ports on the module and fixtures are
safely covered with electrical port covers.
11. Restore circuit power at electrical service panel. Turn on master switch on junction box and turn on switches on each individual fixture.
Master switch can be used to control all fixtures simultaneously or fixtures can be operated individually.
IMPORTANT SAFETY INSTRUCTIONS:
• Read all the instructions before installation. Save instructions for later use.
• Turn off power at fuse or circuit breaker box before installation or before doing any maintenance work.
• Do not exceed the nominal supply voltage or amperage rating.
• Do not install any lampholder closer than 6” from any curtain or similar combustible material.
• Warning: Risk of burns. Lamps are extremely hot when lit. Allow lamps to cool down in temperature before handling.
• Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with National
Electrical Code and local codes. Use of accessory equipment is not recommended.
• Installing contrary to instructions may cause unsafe conditions.
• Warning: Risk of fire. Most dwellings built before 1985 have supply wire rated at 60°C. Consult a qualified electrician before installation.
• To avoid hazards to children, account for all parts and properly dispose of all packing materials.
• Call the Technical Support department at ConTech Lighting with any installation questions: 847.559.5500.
All specifications subject to change without notice.
1-847-559-5500
www.contechlighting.com
This document can be recycled.
LPAJB INST
For ConTech Lighting LPL and LPU LED Lighting Series Junction Box: LPAJB
Captive Screw Cap
Junction Box Cover Screws
USING TWO TYPE SUPPLY WIRE:
(BX) OR (NM) CABLE (2C+ GROUND)
Lockwashers
Master Switch
Junction Box Cover
Flat Non-Metallic
Cable (NM)
MC Connector Locknut
Jumper Cable to
Connect to Fixtures
(Sold Separately)
Captive Screw
Armored Cable (BX)
3/8" Miniature Die-Cast
Electrical Connector
Direct Wire Junction Box
Push-In Wire Connector
Side Knockouts
Electrical Port
3/8" Miniature Die-Cast
Electrical Connector
Jumper Cable to
Connect to Fixtures
(Sold Separately)
Electrical Port Cover
Hardwire Power Cord
Electrical Port Cover Screw
Armored Cable (BX)
Jumper Cable to
Connect to Fixtures
(Sold Separately)
3/8" Miniature Die-Cast Electrical Connector
3/8" Miniature Die-Cast Electrical Connector Locknut
LED Strips
LED Strips
Side Knockouts
N
H
G
Jumper Cable to Connect to Fixtures
(Sold Separately)
Captive Screw
3/8" Miniature Die-Cast Electrical Connector Locknut
3/8" Miniature Die-Cast Electrical Connector
PUSH-IN WIRE CONNECTORS
H: Hot/Black
N: Neutral/White
G: Ground/Green or Bare Copper
LED Strips
Hardwire Power Cord
All specifications subject to change without notice.
1-847-559-5500
www.contechlighting.com
This document can be recycled.
LPAJB INST
Download