0715-AS150HP-D-2 Pg 1 of 3 Ancorsteel 150 HP ® Ancorsteel 150 HP is a water atomized low-alloy steel powder for high performance applications. The prealloyed 1.5 w/o molybdenum addition permits extremely good compressibility and provides good response to heat treatment. Ancorsteel 150 HP is a good base powder for a wide range of hybrid alloy systems. Typical Analysis and Properties Composition (weight %) (w/o) C <0.01 Mn Mo O 0.12 1.5 0.08 Flow Rate Apparent Density 25 s/50g 2.95 g/cm3 Sieve Distribution (w/o) Micrometers +250 U.S. Standard Mesh (+60) Trace -250 /+150 -150 /+45 (-60 /+100 ) (-100 /+325) 66 11 -45 (-325) 23 The Effect of Compaction Pressure on Ancorsteel 150 HP with 0.5 w/o Zinc Stearate Green Density Green Strength Compaction Pressure (tsi) 35 40 45 50 28 7.1 Green Strength (MPa) Green Density (g/cm3 ) Compaction Pressure (tsi) 35 40 45 50 4000 26 7.2 7.0 6.9 6.8 6.7 6.6 24 22 3000 20 18 16 14 2000 12 10 6.5 6.4 30 Green Strength (psi) 7.3 30 8 400 500 600 Compaction Pressure (MPa) 700 Ancorsteel 85 HP Ancorsteel 150 HP NORTH AMERICA Cinnaminson, NJ: +1-856-829-2220, tim.hale@hoeganaes.com EUROPE Meerbusch, Germany: +49-2132-6598-20, klaus.vossen@hoeganaes.com 400 500 600 700 Compaction Pressure (MPa) Ancorsteel 2000 Ancorsteel 4600 V ASIA Seoul, Korea: +82-2-3486-4471, jongsik.na@hoeganaes.com Pudong Shanghai, China: +86-21-2037-3950, oliver.he@hoeganaes.com 0715-AS150HP-D-2 Data Sheet Pg 2 of 3 Ancorsteel 150 HP Properties of Sintered Compacts with Various Graphite Additions 10 8 6 4 2 0 0.2 0.4 0.6 Graphite (w/o) UTS Yield (0.2% offset) 0 1.0 0.8 Dimensional Change Dimensional Change (% from die size) 550 500 450 400 350 300 250 200 150 100 Elongation [% in 25.4 mm (1 inch)] Tensile Strength (MPa) Tensile Properties 0.30 0.25 0.20 0.15 0.10 0.05 0 0 0.2 0.4 0.6 Graphite (w/o) 0.8 1.0 % Elongation Ancorsteel 150 HP plus various amounts of graphite. All specimens were compacted at 620 MPa (45 tsi) and sintered at 1120˚C (2050˚F) for 30 minutes in dissociated ammonia. Tensile Properties 1000 A C F 900 Nickel (w/o) 2 2 4 800 Copper (w/o) 0 1 1 Graphite (w/o) 0.5 0.5 0.5 Tensile Strength (MPa) Material 120 700 100 600 80 500 60 400 300 40 200 Ultimate Tensile Strength 20 100 0 Impact Energy 20 1.5 1.0 0.5 0 A C Material F 15 15 10 10 5 5 0 Impact Energy (ft. lbf) 2.0 Impact Energy (Joules) Elongation [% in 25.4 mm (1 inch)] Tensile Elongation A A C Material A C F 0 Dimensional Change (%from die size) Yield (0.2% offset) 140 Tensile Strength (103psi) Properties of Sintered Compacts of Ancorsteel 150 HP C Material 0.20 F 0 Dimensional Change 0.15 0.10 0.05 0 -0.05 -0.10 A C Material F F All specimens were compacted at 620 MPa (45 tsi) and sintered at 1120˚C (2050˚F) for 30 minutes in dissociated ammonia. NORTH AMERICA Cinnaminson, NJ: +1-856-829-2220, tim.hale@hoeganaes.com EUROPE Meerbusch, Germany: +49-2132-6598-20, klaus.vossen@hoeganaes.com ASIA Seoul, Korea: +82-2-3486-4471, jongsik.na@hoeganaes.com Pudong Shanghai, China: +86-21-2037-3950, oliver.he@hoeganaes.com 0715-AS150HP-D-2 Data Sheet Pg 3 of 3 Ancorsteel 150 HP Sinter-hardening (Effects of Accelerated Furnace Cooling) Material A C F Nickel (w/o) 2 2 4 Copper (w/o) 0 1 1 Graphite (w/o) 0.5 0.5 0.5 Apparent Hardness 1300 180 1200 1100 160 1000 140 900 120 800 700 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 100 7.5 40 Apparent Hardness (HRC) 200 Ultimate Tensile Strength (103 psi) Ultimate Tensile Strength (MPa) Tensile Strength 1400 35 30 25 20 6.7 6.8 Sintered Density (g/cm3) 6.9 7.0 7.1 7.2 7.3 7.4 7.5 Sintered Density (g/cm3) A C F Impact Energy 15 20 15 10 10 5 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 Impact Energy (ft. lbf)) Impact Energy (Joules) 25 5 7.5 Sintered Density (g/cm3) All compacts were prepared with 0.5 w/o graphite and 0.5 w/o zinc stearate They were compacted at 620 MPa (45 tsi) and sintered at 1120˚C (2050˚F) for 30 minutes in dissociated ammonia followed by accelerated cooling in the water jacketed cooling zone. IMPORTANT NOTICE: The data shown are based on laboratory processing standard test specimens. Results may vary from those obtained in production processing. NORTH AMERICA Cinnaminson, NJ: +1-856-829-2220, tim.hale@hoeganaes.com EUROPE Meerbusch, Germany: +49-2132-6598-20, klaus.vossen@hoeganaes.com ASIA Seoul, Korea: +82-2-3486-4471, jongsik.na@hoeganaes.com Pudong Shanghai, China: +86-21-2037-3950, oliver.he@hoeganaes.com