Edco SHAS Series

advertisement
Surge Protective Device
Edco SHAS Series
Highway Lighting Protection
Voltage
Current
Connection
Mounting
120-480 VAC
15 Amp
12 AWG Wire Leads
(provided) on Input & Output
Flange
*See Ordering Information for model number selection
The Edco SHAS Series surge protector is a compact device that is designed to
be installed directly within a light pole to protect the sensitive lighting ballast or
power supply from damaging transients. The Edco SHAS Series easily fits into the
3” x 5” hand hole located at base of the light pole and is wired in series with the
load for the best performance. This series contains a green status LED that will go
out in the event the units protection has been reduced. This enables maintenance
personnel to identify if the unit needs to be replaced.
General Technical Specifications
Model
SHAS-120
SHAS-240
SHAS-277
SHAS-480
Operating Voltage
120 VAC
240 VAC
277 VAC
480 VAC
Maximum Continuous Operating
Voltage (MCOV)
150 VAC
320 VAC
320 VAC
550 VAC
Voltage Configuration
Single Phase, 2W + G
Continuous Operating Current
Operating Frequency
Modes of Protection
Features
15 A
47-63 Hz
L-N, L-G, N-G
Total Peak Surge Current Rating
L-L, L-G
L-N, L-G, N-G
L-L, L-G
■■ All modes of protection
36 kA
Clamping Voltage:
@200A Ringwave
400V (L-N)
708V (L-L)
708V (L-N)
1,500V (L-L)
@500A Combination
394V (L-N)
684V (L-L)
684V (L-N)
1,260V (L-L)
@3kA Combination
564V (L-N)
876V (L-L)
876V (L-N)
1,780V (L-L)
1,160V (L-N)
1,400V (L-L)
1,400V (L-N)
2,560V (L-L)
@10kA Combination
Status Indication
Green LED
Connection Type
Series Connected
Wire Type
Operating Temperature
Dimensions (in/mm)
Weight (lbs/kg)
■■ ‘Protected’ status LED
■■ Compact design - fits easily in
highway or parking lot light pole
■■ Proven Water Resistance Test Report Available
■■ 5 year warranty
#12 AWG (See Wiring Chart on pg. 2)
-40°C to +60°C
1.5”H x 2.0”L x 2.0”W
[38.1 x 50.8 x 50.8 mm]
0.52 lbs [0.24 kg]
Ordering Information
MODEL
■■ Series connected surge protection
APPLICATION
SHAS-120
120VAC, Single Phase, 2W+G
SHAS-240
240VAC, Single Phase, 2W+G
SHAS-277
277VAC, Single Phase, 2W+G
SHAS-480
480VAC, Single Phase, 2W+G
Installation Instructions
V DANGER!
Only qualified personnel should install or service this system. Electrical safety pre-cautions must be followed when installing or servicing this
equipment. To prevent risk of electrical shock, turn off and lock out all power sources to the unit before making electrical connections or servicing.
Seulement le personnel qualifié doit installer ou maintenir ce systéme. Des précautions de sécurité en électricité doivent être suivis lors de
l’installation ou de la maintenance de cet equipement. Pour eviter tout risque de choc électrique, débranchez et verouiller toutes les sources
d’alimentation de cet equipement avant de.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Check voltage source to verify that the correct model Edco SHAS Series is being installed.
Disconnect power to light pole before beginning installation of surge protector.
Remove hand hole panel on pole to gain access to the light wiring.
Disconnect wire nuts connecting wire from electrical service to light. Check to ensure no voltage is present.
Connect line side of Edco SHAS Series to wire coming from service panel. L1 wire is connected to Line 1 (hot), L2 is connected to
Line 2 or Neutral depending on the voltage.
Connect the load side of the Edco SHAS Series to wires going up to the light. L1 is connected to Line 1 (hot), L2 is connected to
Line 2 or neutral depending on the voltage.
Connect the Ground wire on the Edco SHAS Series to the ground lug or screw inside the light pole.
Carefully push the surge protector and wiring back inside the light pole and attach the hand hole panel on pole.
The Edco SHAS Series comes with a green status LED that indicates that power is applied and that the unit is protecting if
illuminated. If the LED is out there is probably no power coming to the unit but can also can indicate that the unit has failed and
needs to be replaced.
Wiring
LEAD LENGTH
GAUGE
COLOR
CONNECTION
22”
12 AWG
Green
Ground
12”
12 AWG
Black
L-1 (Hot)
12”
12 AWG
Black
L-2 (Neutral or Hot)
2.0” [50.8]
2.5” [63.5]
1.5”
[38.1]
2.88” [73.15]
Emerson Network Power Contact information
2.0” [50.8]
www.EmersonNetworkPower.com/Surge
Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
T: (607) 721-8840
T: (800) 288-6169
F: (607) 722-8713
E: SurgeTech@Emerson.com
IO-50137 5/15 Rev. 6 Printed in USA
Emerson Network Power, the Emerson Network Power logo and Edco are trademarks
and service marks of Emerson Electric Co. ©2014 Emerson Electric Co.
While every precaution has been taken to ensure accuracy and completeness herein, Emerson Network Power Surge Protection assumes no responsibility, and disclaims all liability, for damages
resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.
Download