ECE 1201
Engineering Lab II
•
•
•
•
•
Taaruf
Nor Farahidah Za’bah
Room number : E2-2-13.12
Phone number : 03-61964562
Email address : adah510@iium.edu.my
The lab technicians are
– Br. Ahmad Suhairi and Br. Rosley Mahadi
• Course website:
• http://staff.iium.edu.my/asuhairi/koe/
Tentative Week
Experiment No. (Title)
1
2
3
Introductory class – Briefing on the organization of the course
Introduction to PSPICE
PSPICE
Experiment No. 1 & 2
4
(Diode Characteristics & Zener Diode Characteristics)
Experiment No. 3
5&6
(Wave Rectifier & Clipper Circuit)
Experiment No. 4
7&8
(BJT Characteristics & Common-Emitter Transistor Amplifier)
Experiment No. 5
9 & 10
(BJT Biasing Circuits)
Experiment No. 6
11
(MOSFET - Common Source Amplifier)
Experiment no. 7
12
(Inverting and Non-Inverting OP Amp)
Assessment
Pre-lab
10 %
Quiz
15 %
Final Test
30 %
Lab Report
45 %
Safety
• Please wear Kulliyyah jacket and covered
shoes – NO SLIPPER. Otherwise, you will be
asked to leave the lab.
• Power must be switched off whenever an
experiment or project is being assembled,
disassembled, or modified.
Tidiness
• When the experiment has been satisfactory
completed and the results approved by the
instructor, the students may disconnect the
circuit and return the components and
instruments to the locker tidily.
• Chairs are to be slid in properly.
• DO NOT WRITE anything on the table
Pre-Lab Questions and Preparation
• Please complete the pre-lab questions before each lab
sessions.
– It serves as guidance for you while doing your experiment
• Read the entire experiment and research any required
theory beforehand. Many times an experiment takes
longer that one class period simply because a student
is not well prepared.
• The experiment is performed in pairs (max=3 students
per group) but the final exam is performed individually
– One group = one lab report
Lab Reports
• Reports have to be handwritten for submission.
– Writing should appear on one side of each sheet only.
– The students’ name & matric number, section number,
lab session and the lecturer’s
– Please indicate the author of each section in your report.
• This must be followed in the middle of the sheet by:
–
–
–
–
The course code
The experiment number
The title of the experiment
The date on which the student carried out the experiment.
Report format and evaluation
Preparation for PSPICE Tutorial
Tentative Week
Experiment No. (Title)
1
2
3
Introductory class – Briefing on the organization of the course
Introduction to PSPICE – Tutorial 1
PSPICE - Tutorial 2
• Please download the PSPICE software and its tutorial from the
website into your laptop.
• One group will need only need one laptop
Preparation for PSPICE Tutorial
• Download 16.6_OrCAD_Lite_Capture&PSpice_Products.zip
from the any computer in the lab
– It is a zipped file, you have to extract the files into a
designated folder
– Once you have extracted, go to Disk 1 and look for
SETUP (it is an application file) to install the
software.
Introduction to Lab Equipment
• Bread board and its connections
• Function Generator
– To create AC signals such as Sine-Wave, Triangular
Waves etc
– The user can alter its frequency and amplitude
Example of
a function
generator
• Oscilloscope
– An equipment to show the obtained result.
– Has 2 channels
• One for input signal
• One for output signal
• DC power supply
– To provide DC supply to your circuit which you can
measure using digital multimeter