Name
Period
CCNA 2
Chapter 5 Study Guide
Section
1
2
3
4
5
6
7
8
9
10
Question/Topic
5.3.4 Basic
Configuration
What is the correct command sequence to configure
a router host name to "LAB_A"?
A. Router> enable
Router# configure terminal
Router(config)# hostname LAB_A
B. Router> enable
Router# hostname LAB_A
C. Router> enable
Router# configure router
Router(config)# hostname LAB_A
D. Router> enable
Router(config)# host name LAB_A
5.3.4 Basic
Passwords can be used to restrict access to all or
Configuration parts of the Cisco IOS. List the modes and
interfaces that can be protected with passwords.
5.1.4 Cisco
A network administrator needs to configure a router.
IOS
Which of the following connection methods requires
Programs
network functionality to be accessible?
5.3.2 Using
Which tasks can be accomplished by using the
the Cisco IOS command history feature?
CLI
5.3.1
Command
Line Interface
Modes
5.3.5
Configuring
An Interface
5.1.4 Cisco
IOS
Programs
5.2.2 SDM
Express
Configuration
Options
5.2.3
Configuring
WAN
Connections
Using SDM
Express
5.2.2 SDM
Express
Configuration
Options
A router has a valid operating system and a
configuration stored in NVRAM. When the router
boots up, which mode will display?
Which function is a unique responsibility of DCE
devices?
How does SDM differ from the IOS CLI?
What settings can be made in the SDM Express
basic configuration screen?
Which three encapsulation types can be set on a
serial interface by an administrator who is using
SDM Express?
What option within Cisco SDM Express must be
configured to allow hosts that receive IP address
settings from the router to resolve names on the
network or Internet?
5.3.2
Using
11
To save time, IOS commands may be partially
the Cisco IOS entered and then completed by typing which key or
CLI
key combination?
12 5.5.2 Power
How does the SYST LED on the catalyst 2960
Answer
13
Up the Cisco
2960 Switch
5.5.5 Cisco
Discovery
Protocol
14 5.5.5 Cisco
15
Discovery
Protocol
5.3.5
Configuring
An Interface
16 5.2.3
17
18
Configuring
WAN
Connections
Using SDM
Express
5.5.3 Initial
Switch
Configuration
5.3.5
Configuring
An Interface
switch indicate a POST failure?
From a router console, an administrator is unable to
ping a Catalyst switch that is located in another
building. What can this administrator do from her
location to check the IP configuration of the
attached switch?
Which information about a neighbor device can be
obtained by the show cdp neighbors command?
Which series of commands will correctly configure
the serial interface on Router2?
A. Router2(config)# interface S0/0/0
Router2(config-if)# ip address 192.168.6.11
255.255.255.252
Router2(config-if)# clock rate 64000
Router2(config-if)# no shutdown
B. Router2(config)# interface S0/0/0
Router2(config-if)# ip address 192.168.6.11
255.255.255.252
Router2(config-if)# no shutdown
C. Router2(config)# interface S0/0/0
Router2(config-if)# ip address 192.168.6.9
255.255.255.252
Router2(config-if)# clock rate 64000
Router2(config-if)# no shutdown
D. Router2(config)# interface S0/0/0
Router2(config-if)# ip address 192.168.6.9
255.255.255.252
Router2(config-if)# no shutdown
When utilizing SDM Express, which configuration
options allow a router serial interface to obtain an IP
address without manually configuring it?
What command does an administrator use to assign
a default gateway to a switch?
Users on both SW1 and SW2 report that they are
unable to communicate with each other. A network
administrator issues show ip interface brief
commands on both routers to troubleshoot the
connectivity between the two networks. What action
19 5.5.4
Connecting
the LAN
Switch to the
Router
20 5.5.4
21
Connecting
the LAN
Switch to the
Router
5.5.3 Initial
Switch
Configuration
will correct the connectivity issue?
Based on the output of the show port-security
interface fastethernet0/1 command on the switch,
which statement about the switch port is true?
What step must be completed before port security
can be enabled on an interface?
Which three sets of commands are required to
enable administrators to connect to a switch on the
same LAN via Telnet for configuration and
management?
A. Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.2.64
255.255.255.192
B. Switch1(config)# interface fa0/1
Switch1(config-if)# switchport port-security
C. Switch1(config)# interface vlan 1
Switch1(config-if)# ip address 192.168.2.126
255.255.255.192
Switch1(config-if)# no shutdown
D. Switch1(config)# line con 0
Switch1(config-line)# enable password cisco
Switch1(config-line)# login
E. Switch1(config)# line vty 0 15
Switch1(config-line)# password cisco
Switch1(config-line)# login
22 5.3.1
Command
Line Interface
Modes
Switch1(config)# enable secret class
Switch1(config)# exit
Which two statements are true regarding the user
EXEC mode?