DECLARATION OF PERFORMANCE according Annex III of the Regulation (EU) No 305/2011 amended by Commissions delegated Regulation (EU) No 574/2014 No [XYZ-123-abc] [Unique reference number of the declaration of performance (DoP). This No can be chosen by the manufacturer. The reference number of the DoP can be the same as the unique identification code of the product-type.] Unique identification code of the product-type: [XYZ-123-abc] [The unique identification code of the product-type can be chosen by the manufacturer. This could be for example the brand name1) or another unique code clearly linked with the product. It must be ensured that via the unique identification code of the product-type there is clear link between the single product and the relevant DoP.] Intended use/es: Surface protection products – Coating Protection against ingress (1.3) Moisture control (2.2) Increasing resistivity (8.2) [The intended use of the product shall be described using the wording of the hEN] Manufacturer: [name and address of the manufacturer] System/s of AVCP: System 2+ (for uses in buildings and civil engineering works) System 3 (for uses subject to reaction to fire regulations) Harmonised standard: EN 1504-2:2004 Notified body/ies: [name of the NB], [identification no. of the NB], Reaction to fire: [name of the NB], [identification no. of the NB] [The name of the NB shall be provided in the original language, without translation into other languages] 1) [If the brand name of the product will be used as unique identification code of the product-type it should be considered, that the brand name of the product must be changed if the product-type has been changed. If this is not intended, another unique code should be used as identification code of the product-type.] Declared performance/s: EN 1504-2: The product is used in surface protection system: [Model OS 9-System] consisting of components: [ModelScratchfiller] if so [ModelPrimer] [ModelCoat] if so [ModelSealing] Performance in system [Model OS 9-System] Essential characteristics Performance Linear shrinkage NPD Coefficient of thermal expansion NPD Cross cut NPD Permeability to CO2 Water vapour permeability sD > 50 m class I or II or III Capillary absorption and permeability to water w < 0,1 kg/m2 x h0,5 Thermal compatibility ≥ 1,5 (1,0) Resistance to thermal shock NPD Chemical resistance NPD Crack bridging ability B 3.2 (-20 °C) Adhesion strength by pull off test ≥ 1,5 (1,0) 2) N/mm² Reaction to fire class E 3) Skid resistance NPD Artificial weathering NPD Antistatic behaviour NPD Adhesion on wet concrete NPD Release of dangerous substances NPD 2) The 3) Also 2) System of assessment and verification of constancy of performance Harmonised Technical specification System 2+ N/mm² EN 1504-2:2004 System 3 System 2+ value in brackets is the lowest accepted value of any reading possible A1, A2, B, C and D, whereby the last four classes in Germany for the time being need an approval from DIBt. The possible class F is not admitted in Germany. This class means in Germany „readily flammable“. In other European MS this class means „no performance determined“ (NPD)“ and is admitted with consideration of the valid regulation in the respective MS The performance of the product identified above is in conformity with the set of declared performance/s. This declaration of performance is issued, in accordance with Regulation (EU) No 305/2011, under the sole responsibility of the manufacturer identified above. Signed for and on behalf of the manufacturer by: [authorised representative of the manufacturer] (name) [place, date] …………………………………………….. (place and date of issue) (signature) Annex [Option: if necessary to be deleted] According to Art. 6 (5) of the Regulation (EU) No. 305/2011 a Safety Data sheet according Regulation (EU) No. 1907/2006 (REACH), Annex II is attached to this Declaration of Performance. Deutsche Bauchemie e.V. Edition: June 2014