SHILOH OPTIONS
(Shiloh note: you can view these options by going to “products” on my website at
www.sandwichkitchens.com and go also to shilohcabinetry.com)

















ACANTHUS TRIM ONLAYS
APPLIED MOULDING ON CROWN
BASE APOTHECARY (6” WIDE – 5 FUNCTIONING DRAWERS)
BASE APRON CABINET (ACCEPTS AN APRON SINK)
BASE BLIND CORNER
BASE BREAD BOARD
BASE BREAD DRAWER
BASE BREAD DRAWER AND BREAD BOARD
BASE CORBELS
o VARIOUS STYLES AND SIZES
o TRADITIONAL
o MODERN
o TRANSITIONAL
o COUNTRY ENGLISH
o SHELF SUPPORTS
BASE CORNER CABINETS (OPTIONS)
o
o DIAGONAL SINK BASE (FULL DEPTH ADJ. SHELF)
o DIAGONAL SINK FRONT ONLY
o DIAGONAL WITH LAZY SUSAN (TURNTABLES HAVE A HARDWOOD RIM)
o 90 DEGREE CORNER – (OVERLAY) DOORS WITH BIFOLD HINGE: SHELVES WITH A
HARDWOOD EDGE ROTATE INDIVIDUALLY
o 90 DEGREE CORNER – 1 SHELF
o 90 DEGREE CORNER SINK BASE CABINET (NO SHELF)
o 90 DEGREE CORNER WITH ONE OR BOTH SIDES EXPANDABLE TO 33” – 42” , BIFOLD
HINGES, 1 OR NO SHELF)(OPTION AL LAZY TRAY MOUNTED TO BOTTOM AND TO ONE
SHELF )
o 90 DEGREE CORNER - DOORS WITH BIFOLD HINGE: CHROME LAZY SUSAN.
o 90 DEGREE CORNER (INSET) – NO PIANO HINGE: LAZY SUSAN ON A FIXED POLE WHICH
IS ATTACHED TO THE DOOR, (NOT ADJUSTABLE) COMES INSET, ¼” GAP, HARDWOOD
EDGE.
o BASE RIGHT ANGLE RECYCLE CENTER (FOR CORNER – 3 BARRELS)
o RECYCLING CENTER – BIFOLD HINGE – (3) 32 QT. RECYCLING AND REVOLVING BARRELS
ON A POLE.
BASE DESK (ROLLTOP)
BASE DRAWERS (2, 3 OR 4) (NOTE: NO 4 DRAWER IN INSET OR INSET WITH BEAD)
BASE DROP IN RANGE FRONT
BASE FEET
BASE FILE CABINET
BASE ISLAND BAR BACKPANELS
1
o




















5 PIECE PANELS IN VARIOUS STYLES TO MATCH CABINET DOORS (EX. PLACED ON THE
BACK SIDE OF AN ISLAND)
o ¼” PLYWOOD
o ¼” BEADED PLYWOOD
BASE ISLAND END CAP (MANY STYLES WHICH CAN BE SHOWN IF INTERESTED)(THESE ARE REAL
STYLISH OPTIONS TO ACCENT ISLANDS) (EXAMPLE : DIAGONAL WINE RACK WITH COLUMNS
AND BUILT IN 5 PIECE END PANELS. )
BASE ISLAND SPECIFICATIONS (BY #)
o MANY STYLES IN DIFFERING STANDARD DEPTHS AND WIDTHS.
o CONTEMPORARY STYLES
o FORMAL STYLES ETC.
BASE KEYBOARD DRAWER
o FITS IN A 23” WIDE SPACE
o DOES NOT GO IN A DRAWER
BASE KNIFE BLOCK
o SOLID WOOD (FOR DRAWER OPENINGS UP TO 18” WIDE)
BASE LAP DRAWER (MAINLY FOR DESK AREAS TO PUT A CHAIR BELOW)
BASE LAP DRAWER (ANGLED WOOD LEG)
BASE LAP DRAWER (WITH A END PANEL)
BASE LEGS
o 6” HEIGHT
o TABLE FURNITURE LEGS (MINIMUM 27 STYLES)
o TABLE FURNITURE LEGS NOTCED INTO A CABINET OF YOUR CHOICE, DURING
PRODUCTION
BASE NO DOOR CABINETS AND VALANCE AND OTHER STYLES THE SAME AS WALL CABINETS (SEE
“WALL” AREA FOR SIMILAR OPTIONS)
BASE OVEN CABINET (HAS A FUNCTIONING DRAWER BELOW)
BASE PENINSULA CABINETS (NOTE: DRAWERS WILL ONLY OPEN ON 1 SIDE)
BASE – ROLLOUT TRAY CABINET (COMES WITH A STANDARD DRAWER UP TOP WITH A DRAWER
FRONT ON IT AND TWO ROLLOUT TRAYS BELOW BEHIND DOOR(S))
BASE – SINK BASE REVERSE (FUNCTIONING DRAWER ON THE BOTTOM)
BASE – SWING UP APPLIANCE SHELF
BASE TILT OUT TRAY (FOR IN FRONT OF SINK)
BASE TOE MODIFICATIONS
o BUN FEET
o FRENCH LEG
o TAPERED LEG
o VALANCE
o FURNITURE BASE (BASEBOARD)
o QUARTER ROUND
BASE – TRAY BASE CABINET (9, 12 OR 15” )(FOR SHEET PANS) (A DIVIDER DOWN THE MIDDLE
ONLY ARRIVES IN THE 15” WIDE) (DIVIDERS CAN STILL BE PROVIDED IN OTHERS IF REQUESTED)
BASE WARMING DRAWER CABINET (TWO DRAWERS BELOW)
BASE – WASTE (DRAWER ABOVE) (15” = 1 BARREL – 54 QT. TOTAL) (18” & 21” = 2 BARRELS – 72
QT. TOTAL
2


































BASE WASTE: (WITH FULL HEIGHT DOOR) (18” AND 21” WIDE CONTAIN 1 49 QT. BASKET) (36”
WIDE CONTAINS 2 – 49 QT. BASKETS)
BASE WINE CABINETS
o HAS SAME STYLES AS WALL WINE CABINETS
BASE – WIRE TRAY DIVIDER (FOR 15” TRAY BASE CABINETS)(OPTION)
BASE – 3 DRAWER CABINET (MAX # DRAWERS FOR INSET CABINETRY
BASE – 4 DRAWER CABINET (ALL CABINETRY STYLES EXCEPT INSET)
BEADED INSIDE (BACK INTERIOR OF CABINET)
BENCH SEATS
BOOKCASES
BOTTOM – “PREP FINISHED UNDERSIDE OF WALL CABINETS” - EX. IF A DESK BELOW.
CONSTRUCTION MATERIALS AND FOR THE LATEST CHANGES: SEE SHILOCABINETRY.COM OR
SEQUOIACABINETRY.COM FOR DETAILS
CORBELS
COLUMNS (3”, 4” , 5”)
COLUMN OVERLAY (1.5” WIDE COLUMNS BUILT INTO A FILLER OR ON EXTENDED FRAME OF
CABINET)
CUSTOM SIZING (TO 1/8” )
CUSTOM APPLIANCE PANELS
CUTLERY DIVIDERS
DESK DRAWER
DESK – ROLL TOP
DOOR DETAIL (DOORS OVER 23.5” WIDE TO HAVE A CENTER STILE – UNLESS SELECT “BUTT
DOORS”)
DOORS: MANY STYLES OF WOOD GRILL CONFIGURATIONS
DOOR/DRAWER FRONTS (CAN GET LOOSE IN ANY SIZE)
DRAWER FRONTS (5 PIECE, 1 PIECE, 1 PIECE SCULPETD) (NOTE: 5 PIECE IS AN UPCHARGE)
DRAWERS OPTION: DOVETAIL DRAWERS (NO CHARGE IN PLY OPTION) (SHILOH ONLY)
DRAWER : SLIDES: 7/8” EXTENSION HETTICH FOR FULL OVERLAY AND FRAMELESS
DRAWER : SLIDES: FULL EXTENSION BLUM FOR INSET
DRESSING ROOM ACCESSORIES
o VALET ROD
o BELT RACK
o TIE RACK
o IRONING BOARD ON SLIDES
DRESSING ROOM BENCH CABINETS
o DRAWERS
o DOORS
o OPEN SHELF (FINISHED INTERIOR SAME AS EXT.)
DRESSING ROOM HAMPER BASE CABINET
DRESSING ROOM TROUSER RACK BASE CABINET
DRESSING ROOM SHOE BASE CABINET
3















DRESSING ROOM UTILITY CABINETS (ALL STANDARD 84” TALL) (HEIGHT CAN BE MODIFIED)
DRESSING ROOM UTILITY CABINET
o ANGLED
o 5 SHELVES (FULL DEPTH)
DRESSING ROOM UTILITY CABINET
o ANGLED
o ROTATING SHOE RACKS
o STANDARD FOR MENS SIZE SHOES (HOLDS 20 SHOES)
o
DRESSING ROOM UTILITY CABINET
o 5 DRAWERS BELOW
o OPEN SHELVING ABOVE (FULL DEPTH SHELVES IS STAND)
o STANDARD FINISHED INTER. SAME AS EXT.
o STANDARD FLUSH TOE KICK
DRESSING ROOM UTILITY CABINET
o CLOTHES ROD ABOVE
o 3 DRAWERS BELOW
o
DRESSING ROOM UTILITY CABINET
o ALL OPEN SHELVING (FULL DEPTH SHELVES)
o
DRESSING ROOM UTILITY CABINET – HAMPER
o HAMPER BELOW ON SLIDES AND OPEN SHELVING ABOVE
DRESSING ROOM UTILITY CABINET – JEWELRY
o 5 DRAWERS
o TOP DRAWER IS A 2 TIER JEWELRY ORGANIZER.
DRESSING ROOM UTILITY CABINET - SHOES
o SHOES SIT ON ANGLED SHEVES WITH WOOD EDGE
DRESSING ROOM UTILITY CABINET – SHOES
o ROTATING SHOE RACKS
o STANDARD FOR MENS SIZE SHOES (HOLDS 20 SHOES)
o 21” WIDE
DRESSING ROOM UTILITY CABINET – TIE ORGANIZER
o 5 DRAWERS BELOW
o TOP DRAWER (2 TIER) CONTAINS AN AREA FOR TIES AND ANOTHER SLIDE OUT FOR
JEWELRY BELOW THIS
DRESSING ROOM UTILITY CABINET – TROUSER RACK
o ALL OPEN EXCEPT FOR 1 TROUSER PULLOUT ON SLIDES
o
ENTERTAINMENT CENTERS
FILLER PULL OUT SPICE RACK (3”, 6” WIDE)
FINISHES:
o STAINED (NO CHARGE)
o PAINTED (10%)
o STAIN WITH GLAZE (NO CHARGE)
o PAINT WITH GLAZE (10%)
o PAINT WITH HIGHLIGHT (10%)
4
o
o
o












STAIN WITH HIGHLIGHT (GRAPHITE) (no upcharge)
PAINT WITH BRUSHING (10% BRUSH + 10% PAINT)
CUSTOM PAINT (20% )($100. SAMPLE ON 8 ½” X 11” MUST BE PURCHASED – SELLING
AT COST)
o DISTRESSING, WEARING, SAND-THROUGH (NO CHARGE)
o OLDE WORLDE FINISH TECHNIQUE (40%) (WORM HOLING, EDGE AND PANEL GOUGING,
DRY BRUSH GLAZING, ROCK DENTS, CRACKLE, WATER SPOTTING, BROWN UNDERTONE,
& MOCHA HIGHLIGHT GLAZE. DOORS, FRAMES, MOULDING, FINISHED ENDS AND
MISCELLANEOUS ITEMS WILL HAVE VARIOUS FORMS OF THESE FINISH TECHNIQUES. ALL
TECHNIQUES ARE HAND APPLIED AND VARY FROM PIECE TO PIECE.
o WEATHERED COLLECTION FINISH TECHNIQUE (30%) (WORM HOLING, EDGE AND PANEL
GOUGING, WEARING, DRY BRUSH GLAZING, ROCK DENTS, FLY SPECKING, AND BLACK
HIGHLIGHT. DOORS, MOULDING, FINISHED ENDS AND MISCELLANEOUS ITEMS WILL
HAVE VARIOUS FORMS OF THESE FINISH TECHNIQUES. ALL HAND APPLIED AND THE
LEVEL OF EACH TECHNIQUE WILL VARY FROM PIECE TO PIECE.
o VINTAGE COLLECTION (15 %) FLY SPECKING, DRY BRUSH GLAZING & BLACK HIGHLIGHTS.
DOORS, MOULDINGS, FINISHED ENDS AND MISCELLANEOUS ITEMS WILL HAVE VARIOUS
FORMS OF THESE TECHNIQUES. ALL ARE HAND APPLIED & WILL VERY FROM PIECE TO
PIECE.
FLUTED STRAIGHT OR ANGLED CORNER.
FUL DEPTH SHELVES (BASE CABINET – OPTION)
GENERAL
o CLIPPED FLAT OR FLUTED CORNERS
GENERAL
o COLUMN OVERLAYS IN 3 STYLES
o GO ON A FILLER OR AN EXTENDED FACE FRAME
o BOX COLUMNS
 SINGLE PIEC OR HALVES IF SAY FOR EXAMPLE YOU ARE WANTING TO WRAP
AROUND A POLE.
GENERAL
o COUNTERS (PLYWOOD TOP TO MATCH CABINETS WITH HARDWOOD EDGE OR JUST AN
EDGE BANDED EDGE)
GENERAL
o DRAWER PEG SYSTEM (TO ORGANIZE BOWLS AND PLATES)
GENERAL
o EXTENDED STILES
GENERAL
o FACE FRAME AND DOOR ONLY
GENERAL
o FLAT, ANGLED
o FLUTED OR NON FLUTED FILLERS
GENERAL
o FLOATING SHELF (PRICED PER SQUARE INCH – MOUNTS ON A CLEAT SO NO SECURING
HARDWARE IS SEEN)
GENERAL
o FUNCTIONING DOORS ON SIDES OF A CABINET
GENERAL
5
















o END PANELS
o FLUTED ANGLE COLUMNS
o FLUTED FLAT COLUMNS
o
GENERAL
o MOULDINGS (VARIOUS TO MEET CABINETRY NEEDS – ASK FOR PICTURES)
o MIRROR FRAME MOULDINGS (CAN BE PURCHASED – MIRROR COMPANY MUST APPLY
AND INSTALL)
GENERAL
o SPICE DRAWER (INSERTS INTO AN EXISTING DRAWER)
GENERAL
o VALANCES – 1 PIECE
o VALANCES – 5 PIECE
o WINDOW VALANCES (SOME REALLY STAND OUT) (ASK FOR PICTURES)
GENERAL
o WICKER PRODUCE BASKET WITH LINER
GENERAL
o WINE SHELF INSERTS (2 STYLES)
KNIFE BLOCK (SOLID WOOD – NOT AVAILABLE OVER 18” WIDE)
PANELING FOR BACKS OF CABINETS , ISLANDS , ETC.
o 5 PIECE TO MATCH DOORS ALL CUSTOM BUILT INTO A PANEL
o 5 PIECE , INDIVIDUALLY APPLIED.
o FLAT
o BEAD BOARD
o
NO DOOR CABINETS
NO DOOR CABINETS WITH VALANCE UP TOP
NO DOOR CABINETS WITH WICKER BASET
CABINET STYLES:
o 3/8” INSET
o INSET (TYPICALLY A 30% UPCHARGE) (NO UPCHARGE IN SHILOH, WHEN COMPARED TO
“FULL OVERLAY”)
o INSET WITH BEAD (TYPICALLY A 40% UPCHARGE) (NO UPCHARGE IN SHILOH WHEN
COMPARED TO “FULL OVERLAY” )
o FULL OVERLAY (1 ¼”)
o STANDARD OVERLAY (1/2” )
o FRAMELESS (EUROPEAN STYLE)
COUNTER SUPPORTS
METAL AND WOOD INSERTS INSTEAD OF GLASS IN DOORS
WOOD COUNTER SUPPORTS
METAL COUNTER SUPPORT (CUSTOM MADE BY METAL FABRICATOR) (LOW PROFILE)
MODIFICATIONS (ALL UPCHARGES UNLESS NOTED)
o BUTT DOORS (NO WOOD BETWEEN DOORS)
o REMOVEABLE TOE KICK
o FLUSH TOE KICK
o NO TOE KICK
o CUSTOM RECESSED TOE KICK
6
o
o
o
o
o
o
o
o
o
o
o






















FILL WALL OR BASE BLIND AREA
FULL DEPTH SHELVES
CUSTOM HEIGHT ROLLOUTS (4”, 6” 7” OR 10”)
FINISHED INTERIOR (SAME AS EXTERIOR) (NO CHARGE ONLY IF A NO DOOR CABINET)
FULL HEIGHT DOORS (NO UPCHARGE)
NON PENINSULA CABINET TO PENINSULA CABINET
MODIFY HEIGHT, WIDTH, DEPTH (1/3 PRICE AND CAN MODIFY ALL THREE DIMENSIONS
FOR THIS 1/3 PRICE) (NO CHARGE ON FRAMELESS CABINETS)
PREP FINISHED BOTTOM (EXAMPLE, WALL CABINET BOTTOM WHICH WOULD BE SEEN
WHILE SITTING AT A DESK)
BEADED INTERIOR BACK PANEL (MUST ALSO SELECT “FINISHED INTERIOR”)
BEADED FINISHED ENDS
SOFT CLOSE DOORS
SOFT CLOSE DRAWERS
TALL ANGLE UTILITY CABINET (LIKE A CHINA HUTCH) (STANDARD MULLION DOORS UP TOP,
FINISHED INTERIOR AND BUTT DOORS) ( DOORS UP TOP AND DOORS BELOW)
TALL APPLIANCE CABINET (CUTOUTS REQUESTED FOR ANY APPLIANCE ROUGH OPENING)
(USUALLY HAVE A DRAWER (S) BELOW AND DOORS ABOVE THE APPLIANCE)
TALL BOOKCASE S (NUMEROUS STYLES – REQUEST PICTURES)
TALL BROOM CLOSET
TALL CHEF’S PANTRY (FOLD OUT TALL SHELVES) (NO SHELVES ON INSIDE OF DOORS FOR INSET
OR INSET WITH BEAD)
TALL CLOTHES CLOSET
TALL (DRAWERS AND DRAWER FRONTS AT BOTTOM)
TALL ENTERTAINMENT WITH VARIOUS OPTIONS BELOW (REQUEST PICTURES AS HAVE
NUMEROUS OPTIONS)
o MEDIA STORAGE RACK
o SPEAKER CLOTH DOORS (REMOVEABLE SPEAKER CLOTH)
TALL – LAZY SUSAN S ON A CENTER POLE (HAS STORAGE BINS ON INSIDE OF DOORS – EXCEPT
INSET AND INSET WITH BEAD)
TALL PEDIMENT
o GOES ON TOP OF A TALL CABINET
o ARCHED ETC.
o SEE PEDIMENT 1, PEDIMENT 2 ETC.
TALL PULL-OUT PANTRY RACK (NOT AVAIL. WITH INSET OR INSET WITH BEAD)
TALL REFRIGERATOR PANELS
o AVAILABLE IN CUSTOM DEPTHS
o AVAILABLE WITH 5 PIECE DOORS ON SIDES (AS ARE ALL TALL CABINETS)
TALL ROLLOUTS BEHIND DOORS AT BOTTOM
TALL WITH VARIOUS HEIGHT DOORS UP TOP.
VANITY BASE CUSTOM CABINETS
7





















o IF INTERESTED ASK FOR ASSORTMENT OF PICTURES.
o EX. DIFFERING FEET, LEGS, FLUTES, FURNITURE LOOKING
o MANY STYLES
VANITY BASE DEPTHS (MOST VANITIES OFFER EITHER DEPTH AT NO UPCHARGE)
o 18”
o 21”
VANITY BASE FLOATING CABINET
o 2 DRAWER
o DOOR (S)
o NO DOOR
o STANDARD 18 OR 21” TALL
VANITY BASE HANDICAPPED CABIENTS (EXTENDED HEIGHT TOE KICKS ) (SEQUOIA LINE ONLY)
VANITY BASE HAMPER
o 21” DEEP IS STANDARD
o 15” OR 18” WIDE CABINET
VANITYBASE HEIGHTS (30 ½” OR 34 ½”)
VANITY BASE REVERSE - DOORS UP TOP AND FUNCTIONING DRAWER BELOW
VANITY BASE VARIOUS DRAWER AND DOOR OPTIONS TO SUIT NEEDS
VANITY
VANITY WALL CABINETS
o 4 ½” DEEP (ALL DOOR (S)
o 9” DEP DOORS WITH OPEN SHELF BELOW
VANITY
VANITY TALL CABINETS (STANDARD HEIGHT IS 84”)
VANITY TALL CABINETS
o 3 DRAWERS BELOW AND DOOR (S) UP TOP
o SHORTER DOOR BELOW TO MATCH THE HEIGHT OF A VANITY BASE CABINETS DOOR
o
VANITY TALL CABINET
o HAMPER BELOW AND DOOR UP TOP
VANITY TALL CABINET (OTHER STYLES AVAILABLE – ASK FOR DESCRIPTIONS/PICTURES)
o LINEN
o BUN FOOT (3 STYLES TO CHOOSE FROM)
o STANDARD BUTT DOORS
o STANDARD 15” DEEP
o STANDARD WITH GLASS FRAMED DOORS (TOP SECTION)
o DOORS – STANDARD BELOW
WALL APOTHECARY DRAWERS (# OF DRAWERS SIDE BY SIDE VARIES ACCORDING TO THE
WIDTH)
WALL APPLIANCE GARAGE (ROLL UP, 1 DOOR OR 2 DOOR)
WALL BLIND CABINET
WALL BOOKCASE (OPEN AT BOTTOM WHERE SITS ON COUNTER)
WALL CORNER CABINETS
o Square corner (with bi-fold hinge) (not a piano hinge)
8
o















Square corner (with bi-fold hinge) (one or both sides can be custom built to a wider
width)
o WALL ANGLE CABINET WITH OR WITHOUT A LAZY SUSAN AND WITH OR WITHOUT 1
OR 2 DRAWERS BELOW)
o WALL ANGLE CABINET WITH APPLIANCE GARAGE BELOW
WALL DEPTHS OF CABINETS (13” STANDARD ON INSET & INSET WITH BEAD – ALL OTHERS = 12”
STANDARD)
WALL END OF RUN CABINET (ANGLED WITH OR WITHOUT DOORS )
WALL HOODS (WILL NEED TO SHOW PICTURES – TOO MANY TO LIST) (COME WITH OR WITHOUT
BLOWERS) (MOST AVAILABLE WITH LINERS FOR BLOWERS).
WALL HOOD COMPONENT UNITS
o ALL DOORS
o DOORS UP TOP AND SPICE PULLOUT ON SLIDES BELOW (OPTION TO SIT ON COUNTER)
WALL HUTCH ENDS
WALL MICROWAVE CABINET
o 12” OR 13” DEEP WITH A 17 ¾” DEPTH SHELF AT THE BOTTOM
o 18” DEEP CABINET WITH A FINISHED INTERIOR OPENING AT BOTTOM (A MICROWAVE
WHICH SITS ON A COUNTER GOES INTO THIS OPENING)
WALL OVER REFRIGERATOR CABINET (24” DEEP STANDARD)
WALL SPICE CABINETS (OPTION: RACK ON DOOR, OPTION: 3 TIER PULLOUT ON SLIDES, 9” OR
12” WIDE)
WALL LIGHT RAIL (MOULDING AT THE BOTTOM OF WALL CABINETS- SEVERAL OPTIONS)
WALL NO DOOR CABINET (NO UPCHARGE FOR FINISHED INTERIOR- SAME AS EXTERIOR)
WALL (VALANCE AT BOTTOM)(SEVERAL STYLES)
WALLL (VALANCE AT TOP)
WALL WITH VARIOUS BELOW (ALL THE BELOW CAN BE ACQUIRED WITH OR WITHOUT DOORS)
o DRAWERS (1 OR 2)
o SCORED DRAWER
o PIGEON HOLES
o OPEN SHELF
o OPEN SHELF AND PIGEON HOLES
o OPEN SHELF WITH A SCORED DRAWER BELOW
o PLATE RACK
WALL WINE CABINETS
o LATTICE (ON DIAGONAL)
o CROSS (X)(NOTE: CABINET MUST BE SQUARE)
o CROSS (SINGLE)
o CROSS (SINGLE TO ONE SIDE AND BACK TO ORIGINATING SIDE)
o WALL WINE SHELF CABINET (HAS INDIVIDUAL CUTOUTS FOR BOTTLES – ON ADJUSTABLE
SHELVES0
o CUBBIES (6” WIDE UNIT, ONLY)
o STEM GLASS HOLDER (ATTACHES UNDER A WALL CABINET)
WOOD COUNTERS (TO MATCH CABINET COLOR) (EDGED IN 1” WIDE WOOD MOULDING TO
MATCH THE CABINET COLOR)

9




TILT OUT TRAY (FRONT OF SINK)
LEGS (3”, 4”, 5”) APPROXIMATELY 30 STYLES
VALANCE: OVER SINK OR SIMILAR
10