Researches and applied measurements on nuclear physics and atomic power plants fields in the Institute of Isotopes Árpád VERES Scientific advisor Institute of Isotopes of HAS 1525 Bp. Pf. 77 e-mail: veres@iki.kfki.hu 6-10-2009, Hanoi, Vietnam Contents of lecture • Research Departments of Institute of Isotopes. • Nuclear isomers and its applications. • Present state of nuclear fission power plants. (Comparison of IKI-measurements and Pakscalculations for burn up of fuel assembles). The electricity and the nuclear wastes produced by critical power plants. • Accelerator-Driven (spallation), subcritical nuclear fission power plants. • Nuclear fusion power plants. 6-10-2009, Hanoi, Vietnam Departments of the Institute and its research areas: Radiation Chemistry: Radiation and photochemistry of hydrocarbons; Degradation of environmental pollutants e.g. chlorinated aromatic hydrocarbons, reactive textile dyes; Polymer radiation chemistry and mechanism of radiation induced polymerization; Radiation methods for synthesis of polymers for biomedical applications. Surface Chemistry and Catalysis: Studies on surface of highly dispersed metal particles. Structure, catalytic effect of carbonaceous deposits formed during refinery model reactions; Study the selective oxidation of CO (PROX) in presence of hydrogen for fuel cell application; Study of surface species formed on platinum upon chemisorption of low molecular weight hydrocarbons applying Auger spectroscopy. Radionuclide Applications: Identification of various oxidation and coordination states in iron or tin containing catalysts by in situ Mössbauer spectroscopy. Study of radioisotope migration typical of high-level nuclear waste in geological samples (borecores). 6-10-2009, Hanoi, Vietnam Nuclear Research Department •Prompt Gamma Activation Analysis (PGAA) and its applications. •Nuclear spectroscopy with neutron-induced reactions. • Nuclear data measurements and evaluation. Gamma-ray spectrometry and metrology. •In-beam Mössbauer spectroscopy. Research Reactor 20 MW, water cooled, water moderate, thermal flux 1014 cm-2 s-1 6-10-2009, Hanoi, Vietnam Radiation Safety Department • Dosimetry section: Chemical dosimetry; Solid state dosimetry; environmental, accidental, reactor and personal dosimetry; Radiation processing dosimetry; Dosimetry control at high-activity gamma and at high-energy electron irradiation facilities; Radiation protection services • Radioactive Material Registry Section: Center registry of radioactive materials in Hungary; Software development for the central registry. • ICP-MS Mass Spectrometry Laboratory • Nuclear section 6-10-2009, Hanoi, Vietnam Inductively Coupled Plasma Mass Spectrometry (ICP-MS)-IAEA secondary standard laboratory • • • • • • • Environmental samples Samples in connection with radiation protection Safeguards samples Confiscated samples (illicit trafficking) Samples from the field of Nuclear Physics Investigation of catalysts Food samples for authenticity studies 6-10-2009, Hanoi, Vietnam Nuclear section: Nuclear safeguards; Combating illicit trafficking of nuclear materials; Photo excitation; Reactor Spent Fuel Attribute Tester at Paks Power Plan (SFAT) Safeguards measurements of the damaged,re-encapsulated fuel at Paks Power Plan 6-10-2009, Hanoi, Vietnam Nuclear section: Age determination of Uranium sample by gamma-spectrometry 234U 230Th 226Ra 222Rd Low-background iron chamber (20 cm wall thickness) with coaxial HPGe detector Large area (~20 cm2) planar HPGe detector Other laboratories (mass-spectrometry) Our laboratory (gammaspectrometry) 22.2 - 22.6 years 22.4 1.2 years 23.5 0.5 years 23 3 years 6-10-2009, Hanoi, Vietnam Clock: 214Bi/234U 218Po 214Pb 214Bi Nuclear section: Identification Neutron Sources by neutron coincidence technique: R/T-T method Neutron coincidence counting: • • 3He tubes around the source + shift register or pulse train register • Total neutron count, T • Coincidence neutrons, R, from – – – Moderator Neutron detectors (3He tubes) source holder 6-10-2009, Hanoi, Vietnam n-induced fission inside sources 9Be(n, 2n)8Be reaction spontaneous fission Nuclear section: PHOTO EXCITATION 6-10-2009, Hanoi, Vietnam Short chronology of nuclear isomers •1921. Otto Hahn observed the isomeric state of decay of 234Th 234Pa from the - •1935. V. Kurcsatov et al. produced 80Brm by (n,) reaction •1936. C. F. Weizsäcker recognized that the nuclear isomerism may occur whenever the angular momentum of a low-lying state of nucleus differs from the angular momentum of any lower state by several units of h/2. •1938. M. Goldhaber, R. D. Hill, L. Szilard reported conclusive evidence of nuclear isomerism in a stable nucleus. They found that the 4.1 hour - activity of indium could be product by fast neutron 6-10-2009, Hanoi, Vietnam •1939. Pontecorvo et al. observed isomeric state of stable 115In nuclear by x-ray excitation. •1939. M. Goldhaber et al. irradiated indium target with the -rays emitted by 0.5 g 226Ra to obtain isomeric activity by the 115In(,’)115Inm reaction. Negative results. •1954. G. Harbottle estimated the activity of 6oCo and of 182Ta γsources from the measured isomeric number of 115In(γ,γ’)115Inm reactions. •1956. N. Ikeda, K. Yoshihara measured the cross section (σexp) of 111Cdm and 115Inm by 60Co γ-source. •1963. Á. Veres also measured the cross section of isomeric state of ten stable nuclei (77Sem, 87Srm, 89Ym, 107,109Agm, 111Cdm, 115Inm, 179Hfm, 191Irm, 195Ptm, 197Aum, and 199Hgm) by gamma rays of 60Co and estimated its partial level width of activation levels (~1.1 MeV) too. There where between in the range of 10-4-10-7 eV. 6-10-2009, Hanoi, Vietnam 5-09-1962. One of the first measurements of photoactivation of isomers by γ-rays of 60Co. (L. Szirtes, Á. Veres, P. Bedrossián) 6-10-2009, Hanoi, Vietnam Ea Irradiation facility Em Eg The ↻ shows the irradiation and store position of the source. The ↥ shows the install the target in irradiation position. 1. Target nuclei which are excited by γ-rays to the isomeric state. 2. 60Co source (1.3 kCi ~ 48 TBq) 3. Lead container (shielding 2.2 tons) 6-10-2009, Hanoi, Vietnam Chart of the isomers of stable nuclei N 43 Z 34 77Sem 44 47 49 50 52 56 58 60 62 107Agm 109Agm 44.3 s 39.6 s 63 64 65 17.4 s 79Brm 35 4.9 s 83Krm 36 1.83 h 87Srm 38 2.8 h 89Ym 39 16 s 90Zrm 40 0.8 s 93Nbm 41 16.1 y 99Tcm 43 6.01 h 103Rhm 45 56 m 47 48 6-10-2009, Hanoi, Vietnam 111Cdm 111Cdm 48 m 48 m N Z 49 63 65 113Inm 115Inm 1.7 h 4.5 h 50 67 69 117Snm 119Snm 71 73 75 77 79 80 81 99 106 13.6 d 293 d 52 123Tem 125Tem 120 d 57.4 d 54 120Xem 131Xem 8.9 d 12 d 135Bam 56 136Ba 28.7 h 0.3 s 137Bam 2.6 m 167Erm 68 2.6 m 176Ybm 11.4 s 70 N Z 71 72 105 176Lum 3.64 h 106 107 108 177Hfm2 178Hfm2 179Hfm1 180Hfm 51 m 31 y 18.7 s 5.5 h N Z 74 109 183Wm 5.2 s 76 113 114 116 189Osm 190Osm 192Osm 5.8 h 10 m 191Irm 4.9 s 6.1 s 193Irm 10 d 125 207Pbm 0.8 s 127 143 180Tam 73 N Z 78 117 195Ptm 4.02 d 118 1.2 Py 77 119 N Z 82 210Bim 197Aum 79 7.73 s 83 43 m, 3 My 235Um 199Hgm 80 122 204Pbm 67 m 92 25 m 6-10-2009, Hanoi, Vietnam The codes of colors 1 sec to 1 hour: 20 isomers 1 hour to 1 day: 10 isomers 1 day to 1 year : 8 isomers 1 year: 5 isomers scarlet Yellow green blue It was brought up the question in the literature, that whether the mechanism of the isomeric activation has non resonant character or not. Photo excitation in next years IDEA OF NON-RESONANT PROCESS (primary gamma 662 keV directly excitation isomers) • • In this situation, in 1981, during the studies of (,’) reaction being basis on the resonance fluorescence, Ljubicic, Pisk, and Logan [1] suggested that the nonresonant-type process might be dominant in nuclear photoactivation of 115In by 60Co source A technique was give for distinguishing between resonance and non-resonant process Integral cross section of 115In by 60Co excitation 6-10-2009, Hanoi, Vietnam NO-RESONANT and RESONANT [1] A. Ljubicic, K. Pisk, and B. A. Logan, Phys. Rev. C 23, 2238 (1981). [2] M. Krcmar, A. Ljubicic, K. Pisk, B. A. Logan, and M. Vrtar, Phys. Rev. C 25, 2097 (1982). [3] M. Krcmar, A. Ljubicic, B. A. Logan, and M. Bistrovic, Phys. Rev. C 33, 293 (1986). [4] K. Yoshihara, Zs. Nemeth, L. Lakosi, I. Pavlicsek, and A. Veres, Phys. Rev. C 33, 728 (1986). [5]I. Bikit, J. Slivka, I. Anicin, L. Marinkov, A. Rudic, and W. D. Hamilton, Universitet Novi Sad Report 17. Physics Seriet (1987). [6] I. Bikit, J. Slivka, I. Anicin, L. Marinkov, A. Rudic, and W. D. Hamilton, Phys. Rev. C 35, 1943 (1987). [7] J. A. Anderson, M. J. Byrd, and C. B. Collins, Phys. Rev. C 38, 2838 (1988). [8] P. vonNeumann-Cosel, A. Richter, J. J. Carroll and C. B. Collins Phys. Rev. C14, 554 (1991). [9] M. Krcmar, S. Cancic, T. Tustonic, A. Ljubicic, B. A. Logan, and M. Bistrovic, Phys. Rev. C 41, 771 (1990). [10] M. Krcmar, A. Ljubicic, B. A. Logan, and M. Bistrovic, Phys. Rev. C 47, 906 (1993). [11] T. Tustonic, ] M. Krcmar, A. Ljubicic and M. Bistrovic, Appl. Radiat. Isot. 48, 45 (1997). [12] D. A. Bradby, Ithnin Abdul Jalil, M. Krcmar, and A. Ljubicic, Journal of Radianalytical and Nuclear Chemistry 244, 475 (2000). [13] Chea-Beng Lee, D. A. Bradley, Ithnin Abdul Jalil, Y. M. Amin, Mohd Jamil Maah, Khairul Zaman M. Dahlan, Radiat. Phys. Chem. 61, 367 (2001). [14] K. Pisk, M. Krcmar, A. Ljubicic, and B. A. Logan, Phys. Rev. C 25, 2226 (1982). [15] M. Krcmar, A. Ljubicic, and K. Pisk, FZKAAA 18, 171 (1986). [16] Ljubicic, Radiat. Phys. Chem. 51, 341 (1998). [17] Drukarev. 2000. No-resonant excitation of nuclear levels by photon. In: R. W.Dunford, D. S . Gemmel, E. B. Kanter, B. Krassig, S. H. Southworth, L. Young, (Eds), X-rays and Inner Sell Processes, 18 th International Conference, Chicago, IL, August, AIP Conference Proceedings 506, American Institute of Physics, Melville, NY, pp. 496-500 6-10-2009, Hanoi, Vietnam Explain in other way without using the non-resonant process Compton effect in shielding-, absorbermaterial and in target on Resonant flux 6-10-2009, Hanoi, Vietnam Nuclear Power Plants Fission Power Plants Fusion Power Plants 6-10-2009, Hanoi, Vietnam The present state and perspectives of fission and fusion power plants (Types of the nuclear power plants) I. Nuclear fission power plants: I.1. Critical reactor convert energy released from the nucleus of an atom, mainly via of 235U. I.2. Accelerator-driven subcritical reactors used by transmutation of nuclear wastes as fuel. II. Nuclear fusion power plants use the fusion of deuterium and tritium as fuel. II.1. Magnetic confinement . Tokamak-driven. II.2. Inertial confinement. Laser-driven. 6-10-2009, Hanoi, Vietnam I.1. The first n-pile and nuclear power plant December 2, 1942. Nuclear reactor Chicago-Pile-1. USA. (Led by Enrico Fermi, the idea of Leo Szilard). June 27, 1954. Nuclear Power Plant, USSR, Obninsk. It produced 5 MW electric power. 6-10-2009, Hanoi, Vietnam The critical power plants 1. Generation I. Early prototype reactors, i.) 1954, the first nuclear power plant (5 MW) Obninsk, USSR; ii.) 1956, Calder Hall in Sell afield, England a gas-cooled Magnox reactor (50 MW, later 200 MW); iii.) 1957, the Shipping port Reactor (Pennsylvania, USA), pressurized water reactor. 2. Generation II. Commercial reactors 1965-95 (more than 400), LWRPWR, BWR, CANDU, WWR/RBMK. (4 VVR-440 units of Paks, Hungary was installed between 1982-87)* The next 8 slides. 3. Generation III. 1995-2010 Temperature Advanced LWRs, System 80+, AP600, EPR. Gen. III+ 2010-2020 Improved economist. 4. Generation IV. Very High Temperature Reactor (VHTR) called Next Generation Nuclear Plant (NGNP). Completed 2021. Primary goals: improve nuclear safety, proliferation resistance, and to minimize the nuclear wastes. 6-10-2009, Hanoi, Vietnam *Earlier achievements in Paks (Hungary) •Total safety evaluation of the units was accomplished in 1994. •An efficiency enhancement due to reconstruction of the secondary loop and replacements of the turbines increased the original 440 MW of electric power to 470 MW. The total 1790 MW is about 40 % of the Country electricity. •Between 1996 and 2002 the costs of the Programme of Safety Measurements (PSM) amounted to 60 billion Fts. (~ 300 M$). The average sale price of the Paks NPP was 10.16 Ft/kWh in 2008. •The specific costs of generation of the extra-power, the investment cost of the extra-capacity enhancement was shown to be the lowest as compared to the cost of building new different type power plants. Power plant Specific investment costs [bFt/MW] New lignite 350 New gas turbine 125 Biomass 400 Capacity upgrading of Paks NPP ~40 6-10-2009, Hanoi, Vietnam Nuclear section: COMPARISION OF IKI-MEASUREMENTS AND PAKS-CALCULATION FOR BURNUP OF FUEL 4 block of Paks Nuclear Power plant, Hungary 6-10-2009, Hanoi, Vietnam STRUCTURE OF ONE BLOCK VVER-440 REACTOR 6-10-2009, Hanoi, Vietnam STRUCTURE OF VVER-440 REACTOR REACTOR CORE 6-10-2009, Hanoi, Vietnam C-PORCA BURNUP-CALCULATION FOR EVERY 126-RODS OF ALL-ASSEMBLIESS 48 Nodes 126 Rods FUEL ASSAMBLE 6-10-2009, Hanoi, Vietnam IKI- BURNUP-MEASUREMENTS MEASUREMENTAL SET UP Spent fuel assemble Fission Chamber + Si diode detector HP-Ge detector Collimator CZT detector 6-10-2009, Hanoi, Vietnam A TYPICAL GAMMA SPECTRUM MEASURED BY HP-GERMANIUM DETECTOR Ru-Rh106 622 keV Cs134 604,7 keV Cs137 661.7 keV Cs134 795.8 eV Ru-Rh106 1050 keV Ru-Rh106 1128 keV Ru-Rh106 512 keV 1000 Cs134 802 keV Cs134 1168 keV Eu154 1274 keV (a) (c) Cs134 1366 keV (b) Couts (e) (a): Ce-Pr144 696.6 keV 100 Ce-Pr144 1489 keV (d) (b): Eu154 723 keV (c): Eu154 873 keV (d): Eu154 1005 keV (e): Cs134 1039 keV 10 0 500 1000 Energy (keV) 6-10-2009, Hanoi, Vietnam 1500 2000 THE RESULT OF 56993-ASSEMBLE 56993 Axial frofile 56993 3.bl. 4. Radius profile 0,7 20 10 10 50 0,6 Cs134/Cs137 Cs137 20 BU calculation 30 Mear.Cps számolt 40 0,5 0,4 30 0,3 20 0,2 326 350 cal.. 10 0,1 0 0 1700 2200 2700 3200 3700 4200 4700 BU calculation 30 0 -180 -120 -60 0 60 120 0 180 szög Vertical position 24.pozíció él 1 40 30 6 2 20 10 0 5 3 4 Comparison 6-10-2009, Hanoi, Vietnam EXPECTED APPLYCATION OF THE IKI-TECHNIQUE •Control the Burnup calculation •Studying the asymmetry of the Reactor •Problems of security of the Reactor. •Control yield of some fission production The electricity and the nuclear wastes produced by critical power plants 1. In 2007 operated 440 power plants in 32 countries of the world and produced 370 GW-year (~2.6×1012 kWh). This is about 16 % of the world's electricity. 2. If we assume the above level of global nuclear power generation, then in the year 2015 there will be more then 250 000 tons of spent fuels worldwide, containing over 2000 tons of weapons-usable Pu. Over 70 000 tons of this spent fuel (<500 t of Pu) will be in the USA, > 1/3 in Russia and < 1/3 in Europe and others. 6-10-2009, Hanoi, Vietnam The amount of TrU and fission products in 1 ton spent fuel (33 MWd/kg) [g/t] TrU T1/2 (y) [g/t] 239Pu 24 400 5450* 237Np 2 100 000 450 243Am 7 400 100 245Cm 8 500 1,2 Fp. T1/2 (y) 99Tc 210 000 810 135Cs 129I [g/t] 2 300 000 360 16 000 000 170 * Total: Pu : 9 700 The problem: Nuclear waste from commercial power plants contains large quantities of Pu, other fissionable actinides, and long-lived fission product that create challenges for storage and that are potential hazardous proliferation concerns. 6-10-2009, Hanoi, Vietnam I.2. Accelerator-Driven (spallation), subcritical power plants The spallation is a high-energy nuclear reaction in which a target nucleus struck by an incident particle of energy (usually < 500 MeV) ejects numerous lighter particles and becomes a product nucleus correspondingly lighter than the original nucleus. 6-10-2009, Hanoi, Vietnam 50 40 Secund neutrons (n/GeV) The neutron-yields of heavy elements (U, W, Pb) produced by 0.5-5 GeV proton energy [Y = 18-45 neutrons per proton]. 45 35 30 25 20 U-238 15 W 10 Pb 5 0 0 0,5 1 1,5 2 2,5 Protonenergy (GeV) 3 3,5 4 4,5 5 The accelerator can drive 2×500 MWe power plants by transmutation of 400 kg/year of 239Pu and 100 kg/year of other fissionable actinides. 6-10-2009, Hanoi, Vietnam A block diagram of accelerator and ATW configuration 6-10-2009, Hanoi, Vietnam USA concept for the transmutation of spent fuel nuclear wastes. Beller et al, Nucl. Instr. Meth. A463, 468, (2001) On 2036 year the amount of spent fuels will be: > 86 000 ton, in which the most problematic fission products are the 99Tc (93 t) and the 129I (20 t). The ATW systems could be used in a series of different scenarios. 6-10-2009, Hanoi, Vietnam Time schedule and milestones for the development of an accelerator driven systems (ADS) and accelerator driven transmutation (ADT) technology in Europe 6-10-2009, Hanoi, Vietnam Some Accelerator-Driven programs for Transmutations of nuclear wastes •1987. CERN, JRC (Dubna), BNL (13-28 MeV proton-cyclotrone, TRU target/fuel, 900 MWt •1989. JAERI (Japan) OMEGA project salt-solution target •1990. BNL PHOENIX project, 1,6 GeV-104 mA p-linac •1991. LANL ATW, 1016 n/cm2s, 100-180 MeV p-linac, actinide fuel. •1993. CERN (Rubbia), 0,8 GeV-6,25 mA accelerator as driver for a power reactor a target with thorium as fuel and lead as a coolant. •1996. Belgium, MYRHA project, 250 MeV-2 mA proton-cyclotrone. n ~1,5×1015 n/cm2, the volume of zone: 35 cm3 •Many institute of 12 Countries co-operate in 20 project. 6-10-2009, Hanoi, Vietnam FUSION POWER PLANTS II. Nuclear fusion power plants Magnetic Fusion Energy (MFE). Inertial Fusion Energy (IFE). Fusion is the joining together of small, light nuclei to form a larger, more massive nucleus (the deuterium-tritium is the most popular reaction, but there are others). The problem is that combination of high temperatures and densities are required to force positively charged nuclei together, but the resulting high pressure will tend to blow fusion plasma (hot ionized gas) apart. 6-10-2009, Hanoi, Vietnam Fusion Methods: 3 primary plasma confinement. i.Magnetic confinement; ii. Gravitational confinement -- astrophysical contexts; iii.Inertial confinement -- inertia of the fuel confines it for the nanoseconds (10-9 s) required for the fusion reaction to proceed. Difference between magnetic- and inertial confinement: 1. In magnetic confinement, the tendency of the hot plasma to expand is counteracted by the Lorenz force between currents in the plasma and magnetic fields produced by external coils. The particle densities tend to be in the range of 1018 to 1022 m-3 and the linear dimensions in the range of 0.1 to 10 m. 2. In contrast, with inertial confinement, there is nothing to counteract the expansion of the plasma. The confinement time is simply the time it takes the plasma pressure to overcome the inertia of the particles, hence the name. The densities tend to be in the range of 1031 to 1033 m-3 and the plasma radius in the range of 1 to 100 micrometers. 6-10-2009, Hanoi, Vietnam Types of fusion Methods of fusing nuclei Magnetic confinement Tokamak – Spheromack – Stellator – Reversed fiel pinch – FieldRevised Configuration – Leviated Dipole Inertial confinement Laser driven – Z-pinch – Bubble fusion (acoustic confinement) – Fusor (electrical confinement) Other forms of fusion Muon-catalised fusion – Pyroelectric fosion – Mignon – Polywell – Dense pasma focus Devices List of fusion experiments Magnetic confinement devices (20) ITER (International) | JET (European) | JT-60 | Large Helical Device (Japan) | KSTAK (Korea) | EAST (China) | T-15 (Russia) | Tore Supra (France) | DIIID | TFTR | NSTX | ULCEAT | Alcator C-Mod | LDX (all USA) | H-INF (Ausztralia) | MSAT | START (UK) | ASDEX Upgrade (Germany) | TCV (Switzerland) | DEMO (Commercial) Inertial confinement devices. Laser driven (16) and non laser driven (2) NIF | OMEGA | Novette laser | NIKE laser | Argus laser | Ciclop laser | Janus laser | Long path laser | 4 laser | Vulcan laser (all USA) | LMJ | Luli2000 (France) | Gekko XII (Japan) | ISKRA lasers (Russia) | Asterix IV laser (Czeh Republik) | HiPER (European). Non laser driven: Z-machine | PACER (USA) 6-10-2009, Hanoi, Vietnam II.1. Magnetic fusion (ITER) program • ITER is an international tokamak (magnetic confinement fusion) experiment. It builds upon research conducted on devices such as TFTR, JET, JT-60, T-15. The program is anticipated to last for 30 years and cost € 10 billion. Announced in 2005 that ITER will be built in Cadarache, France. • It designed to produce ~ 500 MW of fusion power sustained for up to 1000 seconds. It is intended to be an experimental step between today's studies of plasma physics and future electricity-producing fusion power plants (DEMO). Magnetic fusion has long been heralded as the future of renewable energy, but could it be lasers that hold the key. 6-10-2009, Hanoi, Vietnam II.2. Laser fusion, inertial confinement. Indirect fusion (central ignition heavy ion beams or ion beams) Intense laser beams, focused into a tiny gold cylinder called a hohlraum, will generate a "bath" of soft X-rays that will compress a tiny hollow shell filled with DT to 100 times the density of lead. In the resulting conditions – a temperature of more than millions of degrees and pressures 100 billion times the Earth's atmosphere – the fuel core will ignite and thermonuclear burn will quickly spread through the compressed fuel. In 2010, National Ignition Facility (NIF) will begin experiments that will focus the energy of 192 giant laser beams on a target filled with DT fuel. NIF's goal is to fuse the hydrogen atoms' nuclei and produce net energy gain. Chamber is 10 m diameter. Livermore. Nova laser opened in 1985 (chamber, 10 laser beams converge to heat and shock a tiny hohlraum) It is 9 m high and 4.5 m diameter. Livermore. 6-10-2009, Hanoi, Vietnam Laser fusion, inertial confinement. Direct fusion (fast ignition) • It will capable of firing more than a petawatt of energy at a 2 mm fuel pellet held in place by a bottle. The laser barrage will compress the pellet to just a few microns, that can generate millions of degrees of heat needed for fusion to occur. Compression → Ignition → Burn 6-10-2009, Hanoi, Vietnam High Power laser Energy Research facility (HiPER) • • It is the first experiment designed specifically to study the "fast ignition„ (direct fusion) approach to generating nuclear fusion, which uses much smaller lasers than conventional designs. The design for possible construction in the EU starting 2010. NIF: Input E (1 beam) = 4 MJ. Output E (1 beam) = 20 MJ. Output/Input; Q = 5. But the input E of 192 beams = 330 MJ (Q< 1). HiPER: Input E = 270 kJ (driver and heater lasers). The smaller lasers are much less expensive, therefore the Output E ~ 25-30 MJ. Q ~ 90 - power-for-cost of HiPER is expected to be about an order 100. of magnitude less expensive than like NIF. 6-10-2009, Hanoi, Vietnam The High Average Power Laser Program Phase I. The goal is to establish the technology required for the lasers, target fabrication, target injection, chambers, and final optics, as well as to identify one or more credible chamber concepts (2001-2005). Phase II will provide an integrated demonstration that the main laser IFE components can operate together in a predictable manner and that the performance will scale to a fusion power plant, (2012). Phase III is the Engineering Test Facility (ETF). It would be the first Laser IFE facility to repetitively produce significant thermonuclear burn, (2025). It would expect the laser energy to be between 1.4-2.0 MJ, with a gain of approximately 120, and a fusion output of between 160 to 240 MJ. • • Participants (Institutions): DoD/DoE Labs. (8); Industry (6); University (4). Laser Inertial Fusion Energy (LIFE). Direct ignition. A schematic appears below. 6-10-2009, Hanoi, Vietnam Birds view of the power plant KOYO-F (Japan) Basic specification of KOYO-F (direct fusion) Net output 1200 MWe (4×300) Laser Energy 1.1 MJ Fusion output/pulse 200 MJ Pulse rep-rate in reactor 4 Hz Total output 1519 MWe Thermal to electricity effic. 41.5 % Laser efficiency 11.4 % Some data: Compression laser Heating laser Wave length 3ω 1ω Energy/pulse 1.1 MJ 0.1 MJ Beam number 32 1 bundle Rep-rate 16 Hz 16 Hz 6-10-2009, Hanoi, Vietnam Some Major Laser Fusion Facilities in the World NIF, LLNL, USA GEKKO XII-FIREX, ILE, Osaka, Japan LMJ, CESTA, Bordeaux, France OMEGA-EP, LLE, Rochester US 6-10-2009, Hanoi, Vietnam SG-III, Menyang, CAEP, China ISKRA-5" laser target chamber (Russia) IAEA- FC 2008, 50 years’ Ann. Fusion Res., Oct. 15, 2008, Geneva, SW (Kunioki Mima, Institute of Laser Engineering, Osaka University) 6-10-2009, Hanoi, Vietnam Short summary and conclusions I. Current critical reactors in operation around the world are generally considered II- or III-generation systems. Generation IV reactors are a set of nuclear reactor designs currently being researched. These designs are generally not expected to be available for commercial construction before 2030. II. The subcritical accelerator driven (AD) power plants can also produced electricity and considerably to diminish the nuclear waste from 2030. Most important advantage of the ADS is that the reactor coming to standstill if we switch off the accelerator and with this we can avoid the very hazardous runaway accidents. III. Magnetic fusion has long been heralded as the future of renewable energy, but could it be lasers that hold the key. It is intended to be an experimental step between today's studies of plasma physics and future electricity-producing fusion power plants (DEMO). 6-10-2009, Hanoi, Vietnam IV. Laser fusion power plants are the devices of future. The smaller lasers are much less expensive, therefore the power-for-cost of HiPER is expected to be about an order of magnitude less expensive than like NIF types. Its hopeful that it could become a commercial reality within the next 20 years. V. EXPECTED APPLYCATION OF THE IKI-TECHNIQUE • Control the Burnup calculation • Studying the asymmetry of the Reactor • Problems of security of the Reactor. • Control yield of some fission production THANK YOU FOR YOUR ATTANTIONS 6-10-2009, Hanoi, Vietnam