TM
Attenuator Type-SR
PROFADER
ATTENUATOR
Model number
Low contact resistance
Silver alloy contact materials.
Type-SR
Many interlocking movements type.
Dimensions
Number of circuit
6: 6 circuits
8: 8 circuits
Circuit
P: Potentiometer
H: Bridged-H
Max attenuation
Product type
With clicks
0
φ 6 -0.1
Model number /
Impedance
6P65CS-10kohm
6P65CS-50kohm
6P65CS-100kohm
6P65CS-250kohm
8P65CS-10kohm
8P65CS-50kohm
8P65CS-100kohm
8P65CS-250kohm
6H50CS-600ohm
8H50CS-600ohm
- 600ohm
Impedance
105 ±2
Dimentions
S-2: 8P65CS
Attenuation
2
1
C
C
Attenuation accuracy
Circuit Method (6H50CS, 8H50CS)
φ 45 ±1
0
φ 6 -0.1
Max.32
6
R1
1
3
2
4
Accuracy of Impedance
Cut off (15kHz)
Voltage proof
Insulation resistance
Input level
Rotational life
Terminations (6H50CS, 8H50CS)
133 ±2
S-3: 6H50CS
3
1
4
2
Operating angle
Strength of Nut-Attached
Attached Parts
Stopper strength
Push-pull strength
25.5
218.5 ±2
120ﾟ
3.5
224 ±2
22 ±1
Frequency 1step Total Number Direction of
Range
angle
of steps
attenuation
DC~20kHz 8degs
40
CCW
DC~20kHz 8degs
40
CCW
DC~20kHz 8degs
40
CCW
DC~15kHz 8degs
40
CCW
DC~20kHz 8degs
40
CCW
DC~20kHz 8degs
40
CCW
DC~20kHz 8degs
40
CCW
DC~15kHz 8degs
40
CCW
DC~20kHz 15degs
21
CCW
DC~20kHz 15degs
21
CCW
2-φ3.2
228.5 ±2
S-4: 8H50CS
Attenuation step
0.5dB or less
1~2dB
3dB or more
Error in step
than~30dB:
±0.05 ±2.0dB
0~10dB: Less
±1.0dB,
Less than ±0.1
Less than ±0.2
Max. Attenuation
Less than ±0.1
Less than ±0.2
Less than ±0.4
±2% (Impedance 600ohm), ±5% (other Impedance)
80dB or more
1 Min. at AC500V
100Mohm or more at DC500V
Max. 0.3W
30,000 Cycles Min. (18cycles/min, Insertion loss: 1dB or less)
Type-SR
(Step angle) x (Number of steps) ±2degrees
100Ncm
M3 screw (Length: Panel thickness + 3~5mm)
50Ncm
50N
General specifications
Temp.range
Relative humidity
25.5
φ 45 ±1
0
φ 6 -0.1
Max.32
6
R1
Type-SR
-10 to +60 degrees C (Operating), -15 to +65 degrees C (Storage)
80%RH (No condensation)
Note
30 ±0.2
286.5 ±2
120ﾟ
292 ±2
22 ±1
The products and their specifications are subject to change without notice.
TOKYO KO-ON DENPA CO., LTD. www.tkd-corp.com EDA-201509
Dim.
S-1
S-1
S-1
S-1
S-2
S-2
S-2
S-2
S-3
S-4
BTS-50dB 0, 2, 4, …(2dB step)…, 30, 32, 34, 37, 42, 50, cut off
0, 1, 2, 3, …(1dB step)…, 24, 25.5, 27, 28.5, 30, 31.5, 33.5, 35.5,
BTS-65dB
37.5, 39.5, 42, 45, 48.5, 53, 58, 65, cut off
Mechanical specifications
φ 45 ±1
0
φ 6 -0.1
Max.32
6
R1
30 ±0.2
P
P
P
P
P
P
P
P
H
H
Attenuation
types
BTS-65dB
BTS-65dB
BTS-65dB
BTS-65dB
BTS-65dB
BTS-65dB
BTS-65dB
BTS-65dB
BTS-50dB
BTS-50dB
Type-SR
C
C
22 ±1
Circuit
1
2
CP600 is a Small variable attenuator of the 16mm-square.
It is made to be almost decrement properties of the BSS-50dB(NHK)
attenuator.
Terminations (6P65CS,
8P65CS)
φ 45 ±1
S
Electrical specifications
Circuit Method (6P65CS, 8P65CS)
Max.32
6
R1
120ﾟ
C
*The standard lineups are added or removed without notice.
Cro ss rece ssed head screws M3
22 ±1
50
Order
Number
S-P001
S-P002
S-P003
S-P004
S-P005
S-P006
S-P007
S-P008
S-H001
S-H002
Potentiometer, Bridged-H
120ﾟ
H
STANDARD LINEUPS
2 types attenuation circuits
S-1: 6P65CS
6
296.5 ±2
3.5
2-φ3.2
* Solder heat resistance: 350degrees C max, 5sec max, to twice. (Manual soldering only)
* The solder please use the thing of the same composition. (Solder for wire lapping sticks to a terminal.)
Use solder: SN100C (Sn-0.7Cu-0.05Ni-Ge) NIHON SUPERIOR CO.,LTD.
* Cannot use this product for the signal line using phontom-48V.
* This product is an attenuator of the types to change resistance. Therefore, a switching noise may occur.