Data Sheet
January 2008
CPS2000 Cabinet Power System
Temperature Hardened System
Input (Nominal): 90 Vac to 264 Vac (Autoranging)
Output (Nominal): -48 Vdc (up to 28.8 A) and Optional
50 VA Ringing Generator
The low-maintenance, outside-plant CPS2000
(Cabinet Power System) integrates advanced
technology in a modular system with multiple shelf
configurations for 480 mm (19 in.), 584 mm (23
in.), and optional ETSI mounting adapters. The
CPS2000 is ideally suited for today’s fast-growing
remote telecom applications, particularly those in
harsh environments.
Wide Temperature Range
The CPS2000 is a high-reliability system
incorporating temperature hardened-electronics. It
is suited for use in remote applications at an
extremely wide temperature range, –40 °C to +75
°C (–40 °F to +167 °F) with fan-assisted cooling, or
–40 °C to +50 °C (–40 °F to +122 °F) with natural
convection cooling.
Multiple Outputs
The multiple power bus architecture supports
applications requiring –48 V and ringing voltage,
which can eliminate the need for separate power
plants.
Multiple Configurations
Both shelf assemblies are available in the
following configurations:
■
Rectifier plant with four power module positions
■
Ringer-rectifier plant with up to three rectifiers
and two ringing generators
■
Ringer-only plant with up to six 50 VA outputs
The single-shelf assembly, equipped with plug-in
modules, is 133 mm (5.25 in. or 3U) high and 305
mm (12 in. deep, and can accommodate the
following:
■
540 W nominal 48 V, 7.2 A rectifier
■
50 VA, 100, 80, 75 Vrms and 20 Hz or 25 Hz
ringing generators (half-width power module)
■
Monitor and Control Unit (MCU) or Alarm and
Control Unit (ACU)
■
Low voltage battery disconnect/reconnect
contactor
■
Slope-compensated thermal management
Applications
■
Digital loop carrier
■
Fiber to the curb
■
Remote switching cabinets
■
Ringing plant for co-location sites
■
Wireless base stations
Data Sheet
January 2008
Benefits
■
CPS2000 Cabinet Power System
Temperature Hardened System
■
Maximum Design Efficiency
o The low-profile shelf assembly
is a space-saving 5.25 in. high
by 12 in. deep by 17.35 in. or
21.35 in. wide.
System Safeguards
o Thermal management options,
overcurrent/overvoltage
protection, and low-voltage
battery disconnect provide
protection for equipment and
batteries.
o The system is available for
o Compatible with standard
mounting on 19 in. or 23 in.
racks. Adapters are available
for ETSI mounting (500 mm).
office alarms (Form-C contact
closure).
■
o Power modules, ringing
generators, monitor and
control unit, manual battery
disconnect switches,
low-voltage battery
disconnect, and thermal
management are all housed in
one compact shelf.
o All equipment is front
accessible, ideally suited for
use in cabinets and other
space-restrictive
environments.
Features
■
High power factor
■
High power density
■
Mountable in 19 in. or 23 in.
rack, optional ETSI brackets
(500 mm) available
a wide range of input voltages.
Cost Efficiency
o Unique, lightweight
components and front-access
system architecture reduces
installation and maintenance
expenses.
o Near-unity power factor
correction can result in lower
utility costs.
■
■
2
Enhanced Reliability
o The CPS2000 has been
designed using the latest
technology, strictly controlled
manufacturing processes, and
the highest quality standards
to ensure excellent
performance, superior
reliability, and an extended
service life.
Continuous Operation
o Plug-in modules can be easily
added or replaced without any
interruption of service. System
Safeguards
■
Model ES460C operates from a
nominal 100 Vac, 120 Vac, 200
Vac, 208 Vac, 220 Vac, and 240
Vac source.
■
ES460C provides adjustable
output voltage over the range of
48 V to 56 V at 7.2 A.
■
Model ES461A operates from a
nominal 200 Vac, 208 Vac, 220
Vac, and 240 Vac soure.
■
ES461A provides adjustable
output voltage over the range of
48V to 56V at 9.5A.
■
Both rectifiers provide highly
regulated, low-noise power for
the system loads and for
charging the system batteries.
CPS2000
(Cabinet Power System)
o The system is compatible with
■
Safety/Standards Compliance
o UL-listed*
o CSA† certified
o VDE‡ Licensed
o CE Marked
Rectifier
■
Totally front accessible
■
Temperature-hardened
electronics
■
Battery thermal management
■
Input voltage autoranging
■
Built-in fuse distribution
■
Hot-insertion modular design
■
Overvoltage/overcurrent
protection
■
Low battery-voltage disconnect
option
CPS2000 Ringer-Only Plant
■ Six independent 50 VA ringer
outputs
Ringer Generator
■
Operates at 50 VA using the
output of the rectifiers or the
system batteries.
o Model ES421A 100 Vrms/20Hz
o Model ES422 80 Vrms/25Hz
Monitor and Control Unit
■
Model ES446A MCU provides
display of primary output
voltage and current, output
alarms, plant battery voltage
control, thermal management,
and alarm LEDs.
■
Provides slope thermal
compensation for battery
charging voltage. For battery
temperatures above 25 °C, the
charging voltage is reduced by
72 mV/°C. Optionally, for battery
temperatures below 25 °C, the
charge is boosted by 72 mV/°C.
■
N+1 redundant configuration
* UL is a registered trademark of
Underwriters Laboratories, Inc.
■
Dual, diode isolated, redundant
DC inputs
† CSA is a registered trademark of the
Canadian Standards Association, Inc.
■
Utilizes the standard CPS2000,
ES42x ringing generators for
either 20 Hz or 25 Hz operation
‡ VDE is a registered trademark of
Verband
Lineage Power
Data Sheet
January 2008
CPS2000 Cabinet Power System
Temperature Hardened System
Alarm and Control Unit
■
■
connection for thermal probes,
battery connection points, and
optional battery disconnect
switches. Fourteen GMT-type
fuse outputs are available on the
primary bus. Nine of the outputs
are connectorized and rated for
up to 10 A each and the other
five terminal block outputs are
rated for up to 15 A each.
Economical alternative to MCU
provides plant alarm and control
functions; Model ES447 ACU
provides test points for reading
and adjusting plant voltage.
The ringer only shelf utilizes the
ES490 control unit.
Output Distribution
■
Includes primary and secondary
output distribution built into the
shelf.
■
The 23 in. shelf output
distribution section houses the
low battery-voltage
disconnect/reconnect contactor,
Lineage Power
■
The 19 in. shelf output
distribution section provides
either a bulk output or seven
connectorized, GMT fused
outputs on the primary bus and
connectorized output on the
secondary bus.
■
The ringer-only shelf provides
six connectorized ringer
outputs.
■
A distribution panel can be
ordered for GMT-type fuses. The
ED83310-30 supports dual,
isolated power buses up to 12
fuse-protected outputs per bus.
Batteries
■
Designed to operate with
Lineage Power’s IR and HR
series batteries or any other
type of valve-regulated battery.
3
Data Sheet
January 2008
CPS2000 Cabinet Power System
Temperature Hardened System
Outline Drawing
CPS2000
23-Inch Shelf
CPS2000
19-Inch Shelf
CPS2000 19-Inch
Ringing Shelf
4
Lineage Power
Data Sheet
January 2008
CPS2000 Cabinet Power System
Temperature Hardened System
Specifications
Electrical and Thermal
Input
Voltage Ranges
ac Drain (Rectifier)
Frequency
Power Factor
Efficiency
dc Drain (ringer)
Operating Temperature Range
Harmonic Distortion
Primary Output (Rectifier)
Voltage
Nominal
Range
Current
Output Voltage Regulation
Output Ripple
Electrical and Thermal
Rectifier (ES460C)
Ringer (ES421A)
Shelf (23 in. with LVD)
Shelf (19 in. with LVD)
Ringer Shelf (19 in.)
90 Vac to 264 Vac, single phase
(includes 100 Vac/120 Vac/200 Vac/208 Vac/220 Vac/240 Vac nominal)
autoranging
–40.5 Vdc to –60 Vdc (ringer-only shelf)
5.0 A at 90 Vac, 3.8 A at 120 Vac, 2.5 A at 180 Vac, 1.9 A at 240 Vac
47 Hz to 63 Hz
>0.98 for loads; >60% full load
>85% for loads; >75% full load
1.4 Adc
–40 °C to +75 °C (–40 °F to +167 °F) with fan-assisted cooling
–40 °C to +50 °C (–40 °F to +122 °F) with natural convection cooling
<5% for loads; >60% full load
48 Vdc/52 Vdc/54.5 Vdc
48 Vdc to 57.6 Vdc
Up to 28.8 Adc (7.2 Adc per rectifier)
+0.5%
50 mV peak-to-peak maximum over the range 10 Hz to 20 MHz
Depth
Width
Height
10.5 in.
3.0 in.
4.8 in.
(266.7 mm)
(76.2 mm)
121.9 mm)
10.5 in.
1.6 in.
4.8 in.
(266.7 mm)
(40.6 mm)
(121.9 mm)
11.85 in.
21.35 in.
5.25 in.
(301.0 mm)
(542.3 mm)
(133.4 mm)
11.85 in.
17.35 in.*
5.25 in.
(301.0 mm)
(440.7 mm)
(133.4 mm)
11.6 in.
17.35 in.
5.25 in.
(295 mm)
(440.7 mm)
(133.4 mm)
Ringer Shelf with 7 Ringer Generators
Environmental
Operating/Storage Relative Humidity
Storage Temperature
Audible Noise
Safety/Standards Compliance
Safety
23-in. System
19-in. System
Electromagnetic Compliance:
Emission
Weight
5.25 lb.
(2.4 kg)
2.0 lb.
(0.9 kg)
17.75 lb.
(8.1 kg)
13.25 lb.
(6.0 kg)
14.0 lb.
(6.4 kg)
28.0 lb.
(12.7 kg)
5% to 95%
–40 °C to +85 °C (–40 °F to +185 °F)
<65 dBA
L21, 22 UL-Listed (UL 1950/CSA 950; UL 1801)
L23-25 UL-Listed (UL 1950/CSA 950;UL 1801), CSA certified,VDE Licensed
(EN60950/VDE 0805)
EN55022 (CISPR22) Radiated/Conducted Emission, Class B
Meets FCC Part 15 Class B
IEC/EN61000-3-2 Harmonics
IEC/EN61000-3-3 Flicker
IEC/EN61000-4-2 ESD level 3 and 4
IEC/EN61000-4-3 Radiated Immunity, 10 Vm
IEC/EN61000-4-4 Electrical Fast Transients/Burst, level 4
IEC/EN61000-4-5 Lightning Surge, level X (6 kV/3 kA)
IEC/EN61000-4-6 Conducted Immunity
CE Marking
19 in. shelves, L23, L24, and L25
CE Marked per European Union Council Directives: Low Voltage Directive
(73/23/EEC) and EMC Directives (89/336/EEC) as amended by CE Marking Directive (93/68/EEC)
*List 100 mounting brackets support mounting in a 500 mm frame (515 mm).
Immunity
Lineage Power
5
Data Sheet
January 2008
CPS2000 Cabinet Power System
Temperature Hardened System
CPS2000 Shelves, Rectifiers, Ringers, and Control Units
Comcode
Apparatus Code
Description
108384777
ES460C
48 V, 7.2 A Rectifier (EMI Class B)
408492668
ES461A
48 V, 9.5 A Rectifier
108218462
ES446A
Monitor and Control Unit
107775223
ES447
Alarm and Control Unit
108679986
ES490
Alarm and Control Unit for Ringer Only Shelf
108173279
ES421A
50 VA, 100 Vrms/20 Hz Ringing Generator
107992190
ES422
50 VA, 80 Vrms/25 Hz Ringing Generator
107775306
EDF
LED Board (spare or replacement)
601828817
J85582R-2 L21, L34
CPS Shelf
107999278
J85582R-2 L22, L34
CPS Shelf
107999252
J85582R-2 L22, L43
CPS Shelf
601832462
J85582R-2 L22, L44
CPS Shelf
108982091
J85582R-2 L23, L34
CPS Shelf
108569195
J85582R-2 L23, L43
CPS Shelf
601886328
J85582R-2 L23, L44
CPS Shelf
108985771
J85582R-2 L23, L45
CPS Shelf
601861909
J85582R-2 L24, L52
CPS Shelf
601861925
J85582R-2 L24, L54
CPS Shelf
601861966
J85582R-2 L25, L54
CPS Shelf
601861982
J85582R-2 L25, L62
CPS Shelf
601861990
J85582R-2 L25, L63
CPS Shelf
601862006
J85582R-2 L25, L64
CPS Shelf
108684457
J85582R-2 L91
CPS Ringer-only Shelf
601869142
J85582R-2 L100
Mounting Bracket (75 mm ETSI)
108875312
J85582R-2 L191
Mounting Bracket (40 mm ETSI)
848535217
J85582R-2 L192
Mounting Bracket (23 in.)
Related Product Literature
Document Title
Document Number
CPS2000 (Cabinet Power System)
Air Flow Management (Application Note)
DS03-034
6
Lineage Power
Data Sheet
January 2008
CPS2000 Cabinet Power System
Temperature Hardened System
CPS2000 Power System (J85582R-2) Ordering Information
List Number Description
21
22
23
24
25
31
32
33
34
35
41
42
43
44
45
51
52
53
54
61
62
63
64
91
100
191
192
Provides ac input with one IEC 320-type receptacle for 23 in. shelf
Provides ac input with two IEC 320-type receptacles for 23 in. shelf
Provides terminal block for single ac input for 19 in. and 23 in. shelf
Provides ac input with one IEC 320-type receptacle for 19 in. shelf
Provides dual ac input with two IEC 320-type receptacles powering odd and even slots for 19 in. shelf
Provides 23 in. shelf for ringers and 48 V rectifiers, without battery disconnect switches,
and without low-voltage battery disconnect (LVBD)6,7
Provides 23 in. shelf for ringers and 48 V rectifiers, with LVBD, without battery disconnect switches6
Provides 23 in. shelf for ringers and 48 V rectifiers, with battery disconnect switches, without LVBD6,7
Provides 23 in. shelf for ringers and 48 V rectifiers, with battery disconnect switches and LVBD6,7
Provides 23 in. shlef for ringers and 48 V rectifiers with battery disconnect circuit breakers, LVBD and
two bulk outputs with fuse clips for TPA fuses (max 20A)
Provides 23 in. shelf for 48 V rectifiers only, without battery disconnect circuit breakers and without LVBD6
Provides 23 in. shelf for 48 V rectifiers only with LVBD, without battery disconnect switches
Provides 23 in. shelf for 48 V rectifiers only, with battery disconnect switches, without LVBD6
Provides 23 in. shelf for 48 V rectifiers only, with battery disconnect switches and LVBD6
Provides 23 in. shelf for 48 V rectifiers only with battery disconnect circuit breakers, LVBD and two bulk
outputs, each with fuse clips for TPA fuses (max 20A)
Provides 19 in. shelf for ringers and 48 V rectifiers, with bulk output, without LVBD1,5
Provides 19 in. shelf for ringers and 48 V rectifiers, with bulk output, with LVBD1,5
Provides 19 in. shelf for ringers and 48 V rectifiers, with fused output, without LVBD2,5
Provides 19 in. shelf for ringers and 48 V rectifiers, with fused output, with LVBD2,5
Provides 19 in. shelf for 48 V rectifiers only, with bulk output, without LVBD3,5
Provides 19 in. shelf for 48 V rectifiers only, with bulk output, with LVBD3,5
Provides 19 in. shelf for 48 V rectifiers only, with fused output, without LVBD4,5
Provides 19 in. shelf for 48 V rectifiers only, with fused output, with LVBD4,5
Provides 19 in. shelf for ringing generators only
1. The bulk output distribution for the 19 in. combination ringer and rectifier shelf consists of a single, double hole lug, 48 V output,
and one connectorized, electronically protected ringer output.
2. The fused distribution for the 19 in. combination ringer and rectifier shelf consists of seven connectorized 48 V outputs with
GMT-type fuse protection and one connectorized, electronically protected ringer output.
3. The bulk output distribution for the 19 in. rectifier only shelf consists of a single, double hole lug, 48 V output.
4. The fused output distribution for the 19 in. rectifier shelf only consists of seven connectorized 48 V outputs with GMT-type fuse
protection.
5. The 19 in. shelf configurations are not available with battery disconnect switches because of physical space constraints.
6. All 23 in. shelves are equipped with 14 fused 48 V outputs with GMT-type fuses. Nine of the 14 are connectorized, and five of the
14 are accessible by terminal block.
7. The 23 in. ringer/rectifier shelves are equipped with two connectorized, electronically protected ringer outputs.
LINEAGE POWER
World Wide Headquarters
3000 Skyline Drive, Mesquite, TX 75149, USA
+1-800-843-1797
Outside U.S.A.: +1-972-284-2626
http://www.lineagepower.com
e-mail: techsupport1@lineagepower.com
©2008 Lineage Power. Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of
their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Lineage Power
January 2008
DS03-033 Rev 5
7