Compliance Audit Handbook
This Compliance Audit Handbook has been produced by the Compliance and Assurance Section of the
Department of Environment and Conservation NSW (DEC).
For technical information on the matters discussed in the handbook, contact the DEC Compliance and
Assurance Section on (02) 9995 5000.
Published by:
Department of Environment and Conservation NSW
59–61 Goulburn Street, Sydney
PO Box A290
Sydney South, NSW 1232
Phone: (02) 9995 5000 (switchboard)
Phone: 131 555 (environment information and publications requests)
Phone: 1300 361 967 (national parks information and publication requests)
Fax: (02) 9995 5999
TTY: (02) 9211 4723
Email: info@environment.nsw.gov.au
Website address: www.environment.nsw.gov.au
DEC is pleased to allow this material to be reproduced in whole or in part, provided the meaning is
unchanged and its source, publisher and authorship are acknowledged.
DEC 2006/13
ISBN 1 74137 787 0
Original version: February 1997
Revised: February 2006
Printed on recycled paper
Preface
Purpose of this handbook
This handbook was prepared by the Department of Environment and Conservation NSW
(DEC) as a guide for DEC officers undertaking compliance audits. A compliance audit is an
assessment of an auditee’s activities to determine whether they comply with the relevant
regulatory requirements.
The handbook may also be used by other organisations undertaking compliance audits
including public authorities, industry and industry groups, professional associations,
consultants and contractors; and as an educational resource by students.
The handbook provides general procedures and protocols for conducting compliance audits.
These are designed to ensure a consistent approach to audits, helping to ensure all audits are
adequate, reliable and comparable.
Although the handbook is designed for use as a standalone document, it is recommended that
it be used with the international standard adopted in Australia for environmental auditing:
AS/NZS ISO 19011:2003, Guidelines for quality and/or environmental management systems
auditing (see References).
This handbook has been prepared for the purpose described, and no responsibility is accepted
for its use in any other context or for any other purpose.
Contents
Preface
1 Introduction............................................................................................................................ 1
1.1 What is a compliance audit?................................................................................................ 1
1.2 What is an auditee?.............................................................................................................. 1
1.3 Compliance audit as a regulatory tool in DEC ..................................................................... 1
1.4 Objectives of the compliance audit ....................................................................................... 1
1.5 Knowledge and skills of auditors........................................................................................... 2
2 DEC audit procedures ........................................................................................................... 3
2.1 The audit process ................................................................................................................. 3
2.2 Pre-site visit activities............................................................................................................ 3
2.3 On-site activities.................................................................................................................... 7
2.4 Post-site visit activities .......................................................................................................... 9
3 Quality assurance and record keeping.............................................................................. 13
3.1 Quality assurance ............................................................................................................... 13
3.2 Record keeping................................................................................................................... 13
Glossary .................................................................................................................................. 14
Appendices.............................................................................................................................. 15
Appendix 1 Audit plan ............................................................................................................... 15
Appendix 2 File record of site assessment ............................................................................... 17
Appendix 3 Example of a risk assessment process ................................................................. 18
Appendix 4 Example of a quality plan....................................................................................... 19
References .............................................................................................................................. 20
List of tables
Table 1: Audit activities ............................................................................................................... 3
Table 2: Sample checklist format................................................................................................ 6
Table 3: Compliance, non-compliance, not determined and not applicable assessments ....... 10
Table 4: Regulatory review stages............................................................................................ 12
Table 5: Records to be kept for filing ........................................................................................ 13
1 Introduction
1.1 What is a compliance audit?
An audit is:
‘a systematic, independent and documented verification process of objectively obtaining
and evaluating audit evidence to determine whether specified criteria are met’.
AS/NZS ISO 19011:2003, Guidelines for quality and environmental management systems
auditing (see References).
The specified criteria in compliance audits conducted by the Department of Environment
and Conservation NSW (DEC) are generally the legal and regulatory requirements DEC
administers.
1.2 What is an auditee?
An auditee is a person or organisation being audited. DEC audits organisations or
individuals whose activities are regulated by legislation DEC administers. DEC may audit,
for example, industries operating under environment protection licences or individuals or
organisations holding permits relating to threatened species or Aboriginal objects and
places.
1.3 Compliance audit as a regulatory tool in DEC
DEC has responsibilities and powers under a range of NSW legislation including:
•
•
•
environment protection legislation covering air and water quality, waste, contaminated
land, noise control, pesticides, hazardous chemicals, transport of dangerous goods,
forestry and radiation
conservation legislation protecting biodiversity and threatened species
legislation protecting Aboriginal cultural heritage.
DEC uses compliance audits as one of its regulatory tools, to assess the extent to which a
licensee or other regulated entity is complying with its legal requirements, and to review
achievable environmental standards.
1.4 Objectives of the compliance audit
Compliance audits in DEC are used to achieve the following objectives:
•
•
•
•
•
•
maintaining the integrity of the regulatory system administered by DEC, ie, legislation,
licences, notices, consents
ensuring credible and robust regulation
improving compliance with legislative requirements
through public audit reporting, ensuring DEC’s regulatory activity is open and
transparent
ensuring that statutory instruments are robust and are appropriately used to achieve
desired environmental and conservation outcomes
ensuring that environmental and conservation regulation across NSW is consistent and
transparent.
Compliance Audit Handbook
1
A DEC auditor will:
•
•
•
assess compliance with environmental and conservation legislation. A DEC auditor
may assess compliance with legislation and the statutory instruments administered by
DEC. This may include assessing compliance with conditions attached to statutory
instruments and the broader statutory requirements of various Acts and Regulations.
review statutory instruments issued to the auditee. Activities that may have an
environmental impact are examined to determine whether they are adequately covered by
the instruments. The DEC will review the quality of the instruments by assessing their
conditions or criteria for consistency, their legal enforceability, and their degree of
environmental, conservation or cultural heritage protection.
report findings and follow-up action. A DEC auditor will report on the scope of the audit
and document the assessment of compliance. A follow-up action program may be
established to address non-compliance.
Stakeholders’ awareness of environmental issues and their confidence in DEC’s regulatory
role increase through DEC communicating and promoting audit findings. Stakeholders include
the community, industry and licensees.
1.5 Knowledge and skills of auditors
Auditors should have the necessary knowledge and skills to apply audit principles,
procedures and techniques when undertaking compliance audits. DEC has its own internal
environmental auditor training program. A DEC officer who has undertaken the training and
has demonstrated that they have the required competencies to undertake compliance audits
is eligible for certification as a ‘Provisional Environmental Auditor’ with RABQSA
International.
The auditors will have the knowledge and ability to conduct audits in accordance with this
handbook and any other internal work procedures.
DEC staff conducting compliance audits will act ethically, be objective and without bias, and
be versatile, open-minded and decisive.
Compliance Audit Handbook
2
2 DEC audit procedures
2.1 The audit process
The audit process involves tasks that can be grouped into pre-site visit activities, on-site
activities and post-site visit activities.
Table 1: Audit activities
Activity
Pre-site visit activities
Planning and preparing for the audit
Collecting background information
Compiling checklists
On-site activities
Conducting an opening meeting
Collecting audit evidence through gathering information,
observations and interviews, and sampling
Conducting a closing meeting
Post-site visit activities
Evaluating audit evidence
Compiling a compliance audit report
Developing a follow-up action program
Conducting a regulatory review
More information
see 2.2.1
see 2.2.2
see 2.2.3
see 2.3.1
see 2.3.2
see 2.3.3
see 2.4.1
see 2.4.2
see 2.4.3
see 2.4.4
It is important to understand that an audit’s activities are not restricted to the site visit.
Careful and thorough planning before conducting on-site activities and the post audit
evaluation are just as critical to the audit’s success as the proper conduct of a site
inspection.
2.2 Pre-site visit activities
In achieving a successful audit, the value of good planning and preparation cannot be
overemphasised. Proper planning should ensure that appropriate resources and equipment
are available and time is allocated to carry out the audit in the most efficient and effective
way.
2.2.1 Audit planning and preparation
The audit plan outlines the audit’s objectives, scope and timetable, and the products that the
audit will generate. See Appendix 1 for an example of an audit plan.
An audit plan should include the following key elements:
•
•
•
•
•
the audit objectives
the audit criteria and any reference documents
the audit scope
a quality plan identifying reviews to be undertaken
an assessment of logistics
Compliance Audit Handbook
3
•
•
•
an audit timetable
roles and responsibilities of audit team members
the allocation of appropriate resources to critical areas of the audit.
Audit objectives
The objectives of each compliance audit or audit program must be established at the outset
to direct planning and establish the method for each compliance audit. The objectives define
what the audit will achieve and can be based on various considerations such as
management priorities, or statutory and regulatory requirements.
Audit criteria
The audit criteria are defined requirements against which the auditor compares collected
audit evidence. The criteria may include regulatory requirements, standards, guidelines or
any other specified requirements.
Scope of the audit
The scope defines the extent and boundaries of the audit such as locations; organisational
units, activities and processes to be audited; and the time period covered by the audit
(adapted from ISO 19011:2003 — see References).
Quality plan
The quality plan identifies the quality assurance procedures that will be undertaken during
the audit, for example, ‘Ensure audit plan is reviewed by manager’. See Chapter 3 for more
information about the quality plan and Appendix 4 for an example.
Logistics of conducting the audit
Each audit must be assessed to determine whether there are any potential barriers to it
being successfully carried out. The lead auditor should be aware of any occupational health
and safety requirements for entry to the site including quarantine requirements, whether
appropriate staff will be available or whether bad weather will significantly hamper the
inspection. It may be difficult to be fully aware of all these factors, especially if the audit will
be carried out ‘unannounced’.
The DEC Regional Officer responsible for the site or area will know about any basic
requirements for entry to a site or if there are any other routine operational procedures that
may affect the inspection, eg, hours of operation are limited to weekdays.
Audit timetable
The audit timetable should include the date and places where on-site activities will be
conducted, and the expected time and duration of each activity including the opening
meeting, safety induction when necessary, site inspection and closing meeting.
Selecting the audit team and roles of team members
The lead auditor should determine whether other personnel should be involved in the audit
process. Other DEC officers who have a working knowledge of the auditee should be
involved in the process from the outset to help with audit planning, provide background
information and, if necessary, accompany the auditor on the inspection. Team members
may assist with audit evaluations, comment on draft reports and provide input to the followup action required.
Technical experts may be called in to provide specialist knowledge. They may accompany
the team on the audit inspection if required or be referred to when necessary.
Compliance Audit Handbook
4
The lead auditor should be fully knowledgeable of the audit scope and criteria, lead the site
inspection, be the main point of contact between the auditee and DEC, and ensure the
overall competence of the audit team.
Allocating appropriate resources
The lead auditor needs to ensure DEC officers required for the audit are available on the
day, and ensure that sufficient resources are made available for the audit to be undertaken.
2.2.2 Collecting background information
The purpose of collecting and reviewing background information is to assemble relevant
information that can be used to meet the objectives of the compliance audit. The collection
and review will enable auditors to become familiar with the auditee’s operations, the
statutory requirements and other regulations or guidelines that may apply.
The types of information that should be reviewed include:
•
•
•
•
•
•
•
•
•
•
•
•
site details, such as maps and process descriptions
main environmental issues
technical information about the processes and operations
industry best practice and relevant standards
operating manuals, plans and procedures
company environmental policies and guidelines
statutory and other requirements
previous audits and compliance history
evidence of past environmental performance, such as inspections and complaints
safety requirements
community concerns related to the premises, regional area or industry type
the auditee’s working language, and social and cultural characteristics.
This information may be found in DEC files, reports such as DEC’s Environment Line
reports, environmental impact statements, databases or registers, or on maps. It may also
be necessary to refer to specialists to obtain specific or technical information about the
auditee.
2.2.3 Audit checklists
The audit checklist assists auditors in conducting a thorough, systematic and consistent
audit. Checklists are used to guide on-site observations and help the auditor to assess
whether evidence meets audit criteria.
It is important to remember that checklists are used to jog the auditor’s memory and do not
rigidly dictate exactly what is to be audited.
Compliance Audit Handbook
5
To prepare checklists, the auditor should use a table similar to the example below.
Table 2: Sample checklist format
Criteria/
requirement
Instruction/question
1.1 Licensees who
generate waste must
determine if the
wastes are classified
as ‘hazardous
wastes’.
How is waste generated on-site identified and
classified?
1.2 The occupier of
any premises must
maintain any control
equipment installed
on the premises in an
efficient condition.
1.3 The licensee
must notify the DEC
of any incident
causing or
threatening material
harm to the
environment as soon
as practicable after
the incident has
occurred.
Audit notes
Determine if the licensee follows the relevant
criteria for identifying the specific listing or
characteristics of hazardous wastes.
Are records kept (view documents)?
What control equipment is on the premises?
Is control equipment inspected and maintained
regularly? How often? By whom?
Are inspections/maintenance documented
(view documents)?
Have any such incidents occurred within the
time scope of the audit?
Were these incidents reported to DEC?
Are employees made aware of this
requirement or do work procedures include
information about this requirement?
The first column will list all the requirements the auditee legally needs to meet. The second
column will provide the auditor with instructions to help them determine whether each
requirement has been met. The final column will be left blank so notes can be taken during
the audit.
When developing a checklist, the lead auditor should consider the experience and
knowledge of the auditor who will be using it, and also the environmental risks of the audited
premises. This will enable the lead auditor to select the appropriate level of detail for the
checklist. Experienced auditors can use a checklist that consists of a list of all the topics to
be covered during the course of an audit and does not give details about how to undertake
the auditing of each one. Less experienced auditors should use a detailed checklist that lists
everything they need to know and do. This allows inexperienced auditors to undertake
audits with relatively little supervision from the lead auditor.
Detailed checklists may be required when auditing a premises with high environmental risks.
2.2.4 Providing prior notice of an audit
Generally, all DEC compliance audits are undertaken unannounced. However, when this is
not possible due to logistical reasons or specific circumstances, DEC may undertake
announced audits. If prior notification of the audit is given, the purpose of the audit should be
specified along with the areas to be covered and any information requirements. This approach
improves the chances that appropriate site representatives will be present and that necessary
information will be available. Thus, announced audits have their advantages.
Compliance Audit Handbook
6
Unannounced audits, on the other hand, are more likely to reveal the plant's true operating
conditions, as they offer the ‘true’ snapshot of operations on the day of the audit. They are
particularly useful when there is reason to believe the site is not complying with legislative
requirements and there is a likelihood of environmental impact or harm occurring.
For each individual audit or audit program, the auditor needs to determine if notification
could affect the audit results, and if notice is given, how much is sufficient.
2.3 On-site activities
2.3.1 Opening meeting
The objectives of the opening meeting are to meet with the site manager or their
representative and:
•
•
•
explain and confirm the audit plan, outlining the objectives, scope and audit procedures
provide a short summary of how the audit activities will be undertaken
allow the site manager or their representative to ask questions.
The opening meeting is an important part of the audit process and can set the tone for how
the audit will proceed. It is important to be professional and polite throughout the meeting.
The following information should be conveyed:
•
•
•
•
•
•
•
•
introduce the audit team and provide identification (ie, authorised officer identification)
explain the purpose of the audit
explain the audit objectives, scope and criteria (this will help keep the inspection on
track)
explain the methods and procedures used to conduct the audit
explain the steps that will be taken when preparing the audit report, eg, ‘all audit
evidence collected will be assessed, a draft report will be prepared and reviewed
internally, and the report will be sent to the auditee for comment before being finalised’
agree to an audit timetable to enable the site manager or their representative to arrange
for appropriate personnel to be available during the inspection
ensure that the resources and facilities needed by the audit team are available
determine safety, emergency and security procedures.
2.3.2 Collecting audit evidence
After the opening meeting, the auditor can start collecting and recording audit information.
Some information can be obtained while in the office (ie, viewing or photocopying records)
and the rest can be obtained during the site inspection.
The following tasks should be completed during the site inspection:
•
•
•
•
gather information—take notes, ask open questions (you may wish to review the notes
with the interviewee at the conclusion)
complete audit checklists
document any observed environmental/conservation issues which were not anticipated
during the preparation of the audit checklists
take a photographic record—always inform the site manager or their representative of
your intention of taking photographs during the audit
Compliance Audit Handbook
7
•
•
examine relevant documents, eg, monitoring records, written procedures, site plans,
process diagrams
obtain copies of any documents which may be useful.
Conducting interviews
One important way of collecting information is to interview site personnel. This allows the
results of observation and document review to be verified and enables the interviewee to
explain or clarify those results. Conversely, information collected during interviews needs to
be verified by supporting information from independent sources, such as observations and
records.
Checklists developed during audit planning (see 2.2.3) should be used to prepare for the
interview, but only as a starting point. An experienced auditor is often skilled enough to
follow the flow of the interview and need not feel restricted by the checklist.
Auditors should also prepare questions in advance to keep the interview focused. The
technique and content need to be considered carefully before the audit inspection and
should be adapted to the person being interviewed. Ensure the right site representatives for
the questions being asked are being interviewed.
Environmental sampling
Generally, it is not the auditor's role to carry out sampling. The auditee’s management
should monitor the operation over a period of time and in accordance with the requirements
of the licences, permits, notices, consents, approvals and other documentation relating to
the site. If these monitoring results are not available or a single sample is not scientifically
valid, the auditor should record those facts, not carry out sampling to correct the deficiency.
However, if the facility being audited has limits on discharges, and a discharge is occurring
and there is some uncertainty about the discharge’s quality, the auditor may decide to take
a sample to determine compliance with the limit condition. In this case, the auditor must
collect a sample that represents the condition being assessed and must collect it in a
manner consistent with the collection, handling and preservation principles in AS/NZS
5667.1:1998: Water quality – sampling – guidance on the design of sampling programs,
sampling techniques and the preservation and handling of samples (or any updated version)
(see References).
Documentation verification
When auditing, it is often not possible, due to limited resources, to check every document or
record. The auditor should consider how much documentation should be viewed. The
auditor may choose to sample a statistically representative number of documented results,
such as monitoring data or incident reports. An appropriate sampling method will manage
any uncertainty to an acceptable level.
Potential prosecutions
If a non-compliance is observed on-site that is a serious breach of the law and is likely to
cause environmental harm, the auditor should stop the audit, inform the site manager or
their representative of the situation and collect sufficient evidence in an admissible form for
a potential prosecution. Ideally, this would be done with the DEC Regional Officer who is
responsible for the site or activity. The non-compliance should be evaluated against EPA
2004, EPA prosecution guidelines (see References) for necessary follow-up action.
Compliance Audit Handbook
8
2.3.3 Closing meeting and communication
Once the auditors have finished the site inspection, undertaken all necessary interviews and
collected all necessary evidence, a closing meeting is held with the site representatives.
In the closing meeting, the audit team should:
•
•
•
•
•
give a general indication of the preliminary audit findings—it is important that the auditor
indicates that findings are preliminary and that the final conclusions could be subject to
change once all evidence is considered
provide a briefing on any items needing immediate attention
request any further information identified or clarification needed to finalise audit findings
inform the site manager or their representative that they will be able to comment on the
draft audit findings and the follow-up action program (see 2.4.3)
thank the site manager or their representative for their participation and cooperation.
2.4 Post-site visit activities
2.4.1 Evaluation of audit evidence
Audit findings are generated by evaluating evidence collected before and during the site
inspection against the audit criteria.
The evidence collected may include observations made on-site, records and documentation
on files, and documents produced by the site manager or their representative before, during
or after the site inspection. The evidence is generally assessed once the auditor is back in
the office.
1.
2.
3.
4.
Firstly, the auditor must review information gathered to determine whether sufficient
evidence has been collected to produce audit findings.
The auditor should fill in any information gaps by following up with the auditee’s
representative. This may include accessing records to verify statements made by site
personnel or checking sampling procedures with external consultants who carry out the
monitoring.
Once the information gaps have been filled, the auditor must evaluate the evidence
against the audit criteria and compile a list of audit findings.
If working as an audit team, the list should be discussed among the team, and an
integrated list of all auditors’ findings should be compiled.
The assessments on the following page should be used to report whether each requirement
has been met.
Compliance Audit Handbook
9
Table 3: Compliance, non-compliance, not determined and not applicable
assessments
Assessment
Compliance
Non-compliance
Not determined
Not applicable (not
activated)
Criteria
There is sufficient and appropriate evidence to demonstrate the
particular requirement has been complied with and is within the scope
of the audit.
Clear evidence has been collected to demonstrate the particular
requirement has not been complied with and is within the scope of the
audit.
The necessary evidence has not been collected to enable an
assessment of compliance to be made within the scope of the audit.
There may be various reasons why the audit team could not collect
the required information, including:
the audit team was not on-site for the period covered by the
•
scope of the audit, or there was insufficient information on the
file relating to the period covered by the audit to enable an
assessment of compliance to be made
the
wording of the criteria meant that no evidence could be
•
gathered or it was too difficult to gather the evidence
the environmental gains to be achieved through compliance—
•
and the environmental harm to be caused through noncompliance—did not justify the use of resources necessary to
make an accurate assessment (eg, an auditor should not have
to go to any length to assess compliance with a condition of a
statutory instrument simply because the condition exists).
An invoking element in the criteria was not activated within the scope
of the audit. The element of the criteria may require that a particular
activity be carried out or that an event occur before the requirement
needs to be complied with, eg, ‘The licensee must notify DEC of
incidents causing or threatening environmental harm’. If there were
no incidents that caused or threatened environmental harm within the
scope of the audit, the requirements of this condition do not apply to
the auditee.
The auditor should ensure that only the criteria are assessed, without considering what the
intent is or may have been.
Once compliance with each requirement has been assessed, the auditor should document
their findings in a table similar to the one in Appendix 2. This table can then be used as a
basis for compiling the compliance audit report.
Further observations
The audit report may also document ’further observations’ where issues of environmental
concern were observed which did not strictly relate to the scope of the audit or assessment
of compliance. Further observations are considered to be indicators of potential noncompliance or areas where environmental performance may be improved.
Assessment of the environmental significance of a non-compliance
A non-compliance may be assessed to determine the significance of its actual or potential
impact on the environment. The auditee can use this assessment to rank or categorise non-
Compliance Audit Handbook
10
compliances so follow-up actions can be prioritised if numerous non-compliances are
identified.
The significance of a non-compliance can be assessed by considering factors such as:
•
•
•
•
•
•
•
the level/degree of impact on or significance for Aboriginal objects
the level of threat the species/habitat/community is subject to
the sensitivity of the environment
the toxicity of the pollutant involved
the load of the pollutant
proximity to the receiving environment
likelihood of the event occurring.
Appendix 3 gives an example of a risk assessment process for environmental issues that
allocates a colour code to each non-compliance according to its environmental significance.
Preparing audit conclusions
The audit conclusion is the outcome of the audit after considering the audit objectives and
all findings. The conclusion generally also summarises the extent of conformity of the
auditee with the audit criteria.
2.4.2 Compliance audit report
The compliance audit report communicates audit findings and recommendations to relevant
stakeholders. It documents the overall assessment of compliance, and details the noncompliances identified during the audit and the follow-up actions needed to improve
compliance.
The report must include details of the following:
•
•
•
•
•
•
•
•
the audit objectives
the audit scope
identification of the auditee
identification of DEC as the auditor
the dates and places where the audit activities were undertaken
the audit criteria
the audit findings
the audit conclusions.
The report may also include:
•
•
categorisation of the non-compliances with reference to their environmental risk
recommendations for corrective or preventative action (see 2.4.3 below)
2.4.3 Follow-up action program
The purpose of the follow-up action program is to specify to the auditee a course of action to
deal with non-compliances identified in the audit findings, and achieve compliance. The
action program can be developed with input from auditee representatives to ensure that the
actions required are appropriate and achievable.
Compliance Audit Handbook
11
Developing the follow-up action program involves the following steps:
1.
2.
3.
List all non-compliances with the criteria.
Establish a framework within which the auditee can implement the compliance action
program. This should not contain prescriptive recommendations on how to address the
non-compliances, but should be based on a risk assessment that enables the auditee,
in conjunction with DEC, to prioritise remedial action and determine the timeframe
within which the non-compliances should be addressed (see example in Appendix 3).
Closely monitor the progress of the auditee in implementing the follow-up actions.
2.4.4 Regulatory review
The regulatory review assesses the quality of any statutory instruments issued to the
auditee and recommends improvements if required.
The regulatory review is done in three stages, as a review of:
1.
2.
3.
the legislative requirements, to ensure they are met
the overall adequacy of the statutory instrument
each condition of the statutory instrument.
Table 4: Regulatory review stages
Stage 1. Legislative requirements
•
Review legislative requirements and assess whether all necessary approvals,
licences, permits, consents and notices have been issued to the auditee, and
document findings.
Stage 2. Statutory instruments
•
•
•
Assess the adequacy of each instrument and identify any new conditions that will
improve its performance.
Assess how well the instruments cover all activities/processes/discharges on-site.
Justify findings and document.
Stage 3. Conditions
•
Assess how well each condition meets DEC’s needs by answering the five
questions for each condition:
1.
2.
3.
4.
5.
Is the condition applicable to this site?
Is the condition legally enforceable?
Can the auditee comply with the condition?
Is it possible for DEC Officers to accurately assess compliance with the
condition?
Will compliance with the condition reduce the risk to the environment/cultural
heritage aspects/threatened species?
• Record the assessment.
• Identify additions, modifications and deletions to be made.
• For every condition requiring change or deletion, record the justification.
Compliance Audit Handbook
12
3 Quality assurance and record keeping
The value, rigour and credibility of a compliance audit depends on its proper management.
All DEC compliance audits must be undertaken in accordance with the quality procedures
detailed below.
3.1 Quality assurance
The purpose of quality assurance procedures is to ensure that all audit tasks are carried out
consistently.
At the beginning of each audit, the lead auditor should prepare a quality plan identifying the
quality assurance procedures to be undertaken. The plan should contain:
•
•
•
•
a record of the actions required for ensuring quality work
verification by officers responsible that required actions have been undertaken
the people who will review the work
the expected time for the review.
The plan ensures consistency through a structured process of peer review. An example of a
quality plan is given in Appendix 4.
3.2 Record keeping
The purpose of record keeping is to ensure the proper and systematic recording of
information and observations collected during a compliance audit. Good record keeping and
filing procedures will ensure that all supporting documentation and observations are kept for
future reference.
All audit information should be stored in a file and a new file opened for each compliance
audit. Each file should contain a number of subsections to store the audit information in an
orderly manner.
The table below gives an example of what sort of information should be kept in each file.
Table 5: Records to be kept for filing
File contents
Audit correspondence
Name record
Details
Store all correspondence relevant to the audit
Include the name of the auditee and the history of who occupied the
site and activities carried out.
Quality assurance
and planning
Statutory and policy
documents/guidelines
Audit reference
material and
observations
Include the audit plan and quality plan (see Appendices 1 and 4).
Assessment of
compliance
Compliance Audit Handbook
List all relevant legislation, instruments, policy documents and
guidelines used to assess compliance.
Include all documents generated during the inspection and
preliminary tasks (ie, checklists, photos, drawings, videos).
Include all other information sourced for the purposes of the audit
(eg, location of articles or information sheets).
Include a copy of the compliance audit report including any detailed
assessments documented in other areas (see Appendices 2 and 3).
13
Glossary
Aboriginal object. Any deposit, object or material evidence (not being a handicraft for sale)
relating to the Aboriginal habitation of the area, including Aboriginal remains.
Audit element. A component of the activity/process/discharge that is being investigated for
assessing compliance of a condition attached to a regulatory instrument.
Auditee. A person or organisation being audited. The DEC audits organisations or
individuals whose activities are regulated by legislation the DEC has a duty to uphold.
Checklists. Lists of all the activities, processes and discharges to be addressed during the
audit including a list of elements to be audited and the type of observations to be made to
assess compliance.
Compliance audit. An assessment of an auditee’s activities to determine whether the audit
criteria are being met
Comprehensive audits. Audits that assess all activities, processes and discharges of
auditees in relation to legislation administered by DEC.
DEC policy documents. The general term used to refer to any of the following documents:
corporate policy documents, environmental guidelines, codes of practice, guidelines, policy
statements/strategies, regional environmental improvement plans and policy documents
adopted by DEC. These documents help the auditor assess compliance.
Environmental legislation. Legislation administered by DEC such as the Protection of the
Environment Operations Act 1997 and the Protection of the Environment Operations
(Waste) Regulation 2005.
Focussed audits. Audits that assess targeted activities, processes or discharges of the
auditee in relation to legislation administered by DEC.
Monitor. To systematically and repeatedly measure a parameter to track changes or
establish the baseline or current conditions.
Pollutant. A contaminant that adversely alters the physical, chemical, or biological
properties of the environment. The term includes pathogens, toxic metals, carcinogens,
oxygen-demanding materials, nutrients and all other harmful substances.
Quality assurance. A system of procedures to ensure that all audits are carried out
correctly.
Regulatory review. A process where an assessment of the quality of the statutory
instruments issued to an auditee is undertaken and recommendations made on how to
improve the statutory instruments.
Statutory instruments. Instruments issued to an auditee pursuant to the legislation
administered by DEC. These include approvals, licences, notices, permits and certificates of
registration.
Compliance Audit Handbook
14
Appendices
Appendix 1. Audit plan
Date:………………………………………………………….
Name of auditee: …………………………………………………………………………………….
Address: ………………………………………………………………………………………………
…………………………………………………………………………………………………………..
Date of (proposed) audit inspection: ………………………………………………………..
File no: ………………………………………………..
Lead auditor: ……………………………………………………………………………………….
Support auditors: ………………………………………………………………………………….
…………………………………………………………………………………………………………..
Audit objectives:
………………………………………………………………………………………………………….
………………………………………………………………………………………………………….
………………………………………………………………………………………………………….
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
Audit criteria:
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
Audit scope:
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
Quality plan (attached as Attachment A)
Audit logistics: (ie travel required, limitations on entry to premises, quarantine
requirements)
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
Compliance Audit Handbook
15
Audit timetable:
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
…………………………………………………………………………………………………………..
Roles and responsibilities of audit team members:
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
Resource allocation (ie, budget, personnel):
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
Compliance Audit Handbook
16
Activity/process/
2
discharge/observations
References used to make the assessment
3
(compliance, noncompliance, not
determined or not
applicable)
Assessment
Compliance Audit Handbook
17
1. Legislation, condition, policy requirement etc
2. Identify activity/process/discharge and particular observations to allow an assessment of compliance, non-compliance, not determined or not applicable to
be made
3. Identify checklists, file numbers, photos, videos, notebook page numbers and any other references used to allow an assessment to be made.
Requirement¹
Auditee: …………………………………………………………………………………………………………
Appendix 2. File record of site assessment
Appendix 3. Example of a risk assessment process
This appendix describes one example of a risk assessment process used in DEC. Each
non-compliance is assessed to determine the significance of its actual or potential impact on
the environment. The significance can be assessed by determining the following two criteria
for each non-compliance, using detailed guidance material:
•
•
the level of environmental impact caused by the non-compliance
the likelihood of environmental harm occurring as a result of the non-compliance.
After these assessments are made, the information is transferred into the risk analysis
matrix below, so a colour code can be allocated.
Level of
environmental
impact
Likelihood of environmental harm occurring
Certain
Likely
Less likely
High
Code Red
Code Red
Code Orange
Moderate
Code Red
Code Orange
Code Yellow
Code Orange
Code Yellow
Code Yellow
Low
A red colour code denotes that the non-compliance is of considerable environmental
significance and needs to be dealt with as a matter of priority. An orange or yellow colour
code suggests that the non-compliance could receive a lower priority but must still be
addressed.
Administrative, reporting and monitoring non-compliances are allocated a blue colour code.
These do not usually have direct environmental significance but are still important to the
integrity of the regulatory system.
The colour code is used as the basis for deciding the priority of remedial action required by
the auditee and the timeframe within which the non-compliance must be addressed. While
the risk assessment of non-compliances is used to prioritise actions to be taken, DEC
considers all non-compliances to be important, and auditees must ensure that all are
resolved as soon as possible.
Compliance Audit Handbook
18
Appendix 4. Example of a quality plan
Where appropriate, tasks should be dated and signed off by the person responsible, once they
are completed.
Task
Date
Initial
Audit plan reviewed by Unit Head
Site visit completed and confirmed by lead auditor
*Draft audit report reviewed by support auditor/specialists.
Draft audit report reviewed by:
•
Unit Head
•
Section Manager
Draft audit report submitted to auditee for comment
Response from auditee to draft audit report
Final audit report reviewed by:
•
Unit Head
•
Section Manager
Final audit report sent to auditee
*Follow up of required actions
* = if applicable
Compliance Audit Handbook
19
References
AS/NZS ISO 19011:2003, Guidelines for quality and/or environmental management systems
auditing, visit www.standards.com.au for more information and to purchase a copy
AS/NZS 5667.1:1998, Water quality – sampling – guidance on the design of sampling
programs, sampling techniques and the preservation and handling of samples (or any
updated version), visit www.standards.com.au for more information and to purchase a copy
NSW Environment Protection Authority (EPA) 2004, EPA prosecution guidelines, visit
www.epa.nsw.gov.au/legal/prosguide/index.htm for a copy or phone 131 555
Compliance Audit Handbook
20