OmniBus VDRCS Installation Instructions
The following procedure can be used to install the required OmniBus applications on
Profile model 100, 200, 300 & 400 series.
Important Note: Installation of VDRCS on the Profile XP series requires a different
procedure.

From the Profile Desktop
Profile VDRCS
1. Copy the optional VDRCS_v150_b54_pc.exe and portmapper&services.exe to the
profile c:\temp
2. double click on the files installed in step 1 to install them using c:\ as target
3. edit c:\App_Omn\Appstart.bat using the following information…
**************************** Appstart.bat *******************************
echo off
REM ************* PDR200/300/400 OmniBus Apps Batch file ************
echo Waiting for Tek services to start running.
C:\profile\wait960
echo Starting App_VDRCS . . .
start "OmniBus VDRCS" /D\OmniBus\App_Omn\VDRCS\
\OmniBus\App_Omn\VDRCS\!Run.bat
/MIN
REM out this section if no fibre channel
echo Starting App_Fibre . . .
start "OmniBus Fibre" /D\OmniBus\App_Omn\!App_Fibre\ /MIN
\OmniBus\App_Omn\!App_fibre\App_Fibre.exe
REM out this section if no PLS200
REM echo Starting App_PLS . . .
REM start "OmniBus PLS" /D\OmniBus\App_Omn\!App_PLS\ /MIN
\OmniBus\App_Omn\App_PLS.exe
exit
************************************************************************
4. edit c:\App_Omn\VDRCS\!Run.bat as follows...
****************************!Run.bat************************************
echo off
set Omni$AppVer=150
set Omni$AppBuild=51
set Omni$Develop=1
The next line is for PDR200/300/400: REM out for PDR100
start "OmniBus VDRCS" !App_Vdr\app_vdr.exe
The next line is for PDR100 only: REM out for PDR200/300/400
start "OmniBus VDRCS" !App_Vdr\app_100.exe
exit
************************************************************************
5. Make a shortcut from c:\App_Omn\Appstart.bat on the desktop
6. Test that VDRCS starts by double clicking on the shortcut created in step 5

From the Kalypso Menu Display
System Configuration
(Make sure that the PC and Profile are both connected to the network and that their IP
addresses are on the same subnet)
1. Start Sharer
2. Start system manager
3. Start OUI
4. Log On to sharer (user SYS, no password)
5. Access system manager by clicking on right-hand red switch on OUI taskbar
6. Access ENGINES menu and ADD engine with IP address of the sharer/sysman
pc
7. Name engine added in step 6. "MANAGER" (without quotes), click on MODIFY
8. Access APPLICATIONS menu and ADD application "!APP_MAN3" (without
quotes)
9. Name Application added in step 8. "SYSTEM MANAGER 3" (without quotes),
click on MODIFY
10. Access ENGINES menu and select "MANAGER" engine
11. ADD application "SYSTEM MANAGER 3" to "MANAGER" engine, click on
MODIFY
12. Access stations menu and add workstation "OUI-1" (without quotes)
13. ADD local applications: Machine Control Panel, Router Panel, Filer-Fax and
Omni-Pager, click on MODIFY
14. Log off and log on again, select START, make sure SYSTEM MANAGER 3
application is available
15. Log on to SYSTEM MANAGER 3
16. Run VDRCS on the Profile by double clicking on Appstart.bat on the Profile
desktop
17. Access ENGINES menu on system manager and add engine with the Profile IP
address
18. Name engine added in step 17 "Profile1" (without quotes), click on MODIFY
19. Access APPLICATIONS menu on system manager and add application
"!APP_VDRCS"
20. Name application added in step 19 "Profile1" (without quotes), click on
MODIFY
21. Access ENGINES menu in system manager and select engine Profile1
22. ADD application "Profile1", click on MODIFY
23. PING the Profile from the system manager, it should respond.
24. POLL the Profile from the system manager, it should respond with
"!APP_VDRCS idling at xxx.xxx.xxx.xxx “(ip address)
25. Exit system manager
26. Click on START in the OUI, Profile1 should appear as an application
27. Log on to Profile1
28. Select CONFIG
29. Enter name "Profile1" (without quotes)
30. Select Port 1 and set device type to Profile PDRx00 (depending on which type of
Profile you have)
31. Set Protocol to Profile API
32. Set Chnl No. to 1
33. Set Chnl. ID. to 1
34. enable channel 1
35. Repeat steps 30-34 for the other channels (substituting the appropriate channel,
port and ID numbers)
36. Click on SAVE to save configuration
37. Exit VDRCS
38. Access Local Machine Control Panel on OUI
39. Select ADD, the following list of devices should appear... (assuming a 4-channel
Profile)
Profile1-1
Profile1-2
Profile1-3
Profile1-4