Name ____________________________________ Date __________________
First-Class Levers
LabQuest
30
A lever is a simple machine used to make work easier. It consists of a long, rigid bar with a
support that allows the bar to pivot. The point where the bar pivots is the fulcrum. There are three
classes of levers—first, second, and third. In this experiment, you will examine first-class levers.
Crowbars and scissors are examples of first-class levers. A lever can help you move an object by
increasing the force you exert. Mechanical advantage (MA) is a value that tells the number of
times a machine increases an applied force. You will use a Force Sensor to measure resistance
force and effort force (in newtons). You will then use this information to calculate the
mechanical advantage of each lever.
OBJECTIVES
In this experiment, you will





Measure force.
Calculate actual mechanical advantage (AMA).
Calculate ideal mechanical advantage (IMA).
Calculate percent difference.
Make conclusions about levers.
MATERIALS
LabQuest
LabQuest App
Vernier Force Sensor
500 g mass
loop of string
meter stick
fulcrum
Dual-Range
Force Sensor
Figure 1
PROCEDURE
1. Set the range switch on the Force Sensor to 10 N. Connect the Force Sensor to LabQuest.
Choose New from the File menu. If you have an older sensor that does not auto-ID, manually
set up the sensor.
Middle School Science with Vernier
30 - 1
First-Class Levers
LabQuest 30
2. Zero the Force Sensor with its hook pointing down.
a. Hold the Force Sensor in a vertical position with its hook pointing down. Make sure the
hook and string are not touching anything.
b. When the readings on the screen stabilize, choose Zero from the Sensors menu. When the
process is complete, the readings for the sensor should be close to zero.
3. To measure the resistance force (Fr) for Trials 1, 2 and 3, hang the mass that will be used as
the resistance from the Force Sensor. After the reading has stabilized, record this force
reading in the Resistance Force blanks for Trials 1, 2 and 3.
4. Zero the Force Sensor with its hook pointing up.
a. Hold the Force Sensor in a vertical position with its hook pointing up. Make sure the hook
and string are not touching anything.
b. When the readings on the screen stabilize, choose Zero from the Sensors menu. When the
process is complete, the readings for the sensor should be close to zero.
5. Place a fulcrum near the edge of your lab table. Balance the middle of a meter stick on the
fulcrum as shown in Figure 1.
6. Place the center of the mass that is acting as your resistance force on the 90 cm line
(Dr = 40 cm).
7. Attach the loop of string to the hook of the Force Sensor. Loop the string over the meter stick
at the 10 cm line (De = 40 cm) as shown in Figure 1. With the fulcrum between the effort and
the resistance, this is a first-class lever. Pull down with the Force Sensor until the meter stick
is balanced. Record the force needed to balance the meter stick. This is the effort force (Fe).
8. Place the center of the mass acting as the resistance force on the 70 cm line (Dr = 20 cm). The
position of the effort force (Force Sensor) should not change. Repeat Step 7.
9. Now move the center of the resistance force to the 60 cm line (Dr = 10 cm). The position of
the Force Sensor should not change. Repeat Step 7.
DATA
30 - 2
Trial
Resistance
distance
(cm)
Resistance
force
(N)
Effort
distance
(cm)
1
40
40
2
20
40
3
10
40
Effort
force
(N)
Middle School Science with Vernier
Name ______________________________________________ Date ___________________________
PROCESSING THE DATA
1. Calculate the actual mechanical advantage for each of your three trials using the formula
AMA = Fr / Fe
where AMA = actual mechanical advantage, Fr = resistance force, and Fe = effort force.
Record results in the table that follows Question 3.
2. Ideal mechanical advantage is determined by the formula
IMA = De / Dr
where IMA = ideal mechanical advantage, De = effort distance, and Dr = resistance distance.
Calculate the ideal mechanical advantage of the levers you tested. Record results in the table
that follows Question 3.
3. Calculate the percent difference between IMA and AMA for each of your trials using the
formula
% Difference =
Difference between IMA and AMA
 100
IMA
Record the results in the following table.
Trial
AMA
IMA
Percent difference
1
2
3
Middle School Science with Vernier
30 - 3
First-Class Levers
LabQuest 30
4. What happened to the mechanical advantage as you shortened the resistance distance?
5. How did moving the resistance force closer to the fulcrum affect effort needed to balance it?
6. What was the mechanical advantage of the first lever you tested? Why would a lever like this
be used?
7. Are your values for percent difference between IMA and AMA large or small?
8. Describe some factors that might contribute to the difference between IMA and AMA in this
experiment.
EXTENSION
1. Design and perform an experiment to test second-class and third-class levers. Include a data
table, calculations, and conclusions.
30 - 4
Middle School Science with Vernier