Safety Data Sheet (SDS)
Product Name: SNO-COTE XGLO
REV: JUL 2014
Page: 1 of 3
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Trade Name
Description
SNO-COTE XGLO
A high quality vinyl acrylic based emulsion paint with a brilliant sheen
finish for an improved stain resistance property on interior walls.
Company Identification
Trans-Ocean Coatings & Chemicals Sdn Bhd
Lot 1393, Jalan Meranti
Bintawa Industrial Estate
93450 Kuching, Sarawak, Malaysia
Contact Point
Tel: 6082-334222 Fax: 6082-339189
E-mail: transpaint@yungkong.com
Website: www.transpaint.yungkong.com
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENT
Chemical Name
Vinyl acetate copolymer
Calcium carbonate
Hydrous aluminium silicate
Talc
Petroleum distillates
Sodium salt
Sodium hexametaphosphate
Hydroxyethyl cellulose
Titanium dioxide
Water
Amine
Polyethylene glycol
Formaldehyde
Mixture
Ester alcohol
Essential oil
Propylene glycol
Polyurethane polymer
FA modified polyester
CAS No.
471-34-1
1332-58-7
14807-96-6
68915-31-1
9004-62-0
13463-67-7
7732-18-5
124-68-5
60864-33-7
50-00-0
55965-84-9
25265-77-4
8002-09-3
57-55-6
-
Proportion
High
Medium
Low
Low
Low
Low
Low
Low
Medium
Medium
Low
Low
Low
Low
Low
Low
Low
Low
SECTION 3: PHYSYCAL AND CHEMICAL PROPERTIES
Physical State
Odour
Solubility in Water
Percentage Volatiles
Specific Gravity
Viscosity
Others
Liquid
Mild
Soluble
40
1.33
100 Krebs Unit
Non-flammable
SECTION 4: HAZARD IDENTIFICATION
Eye Contact
Skin Contact
Inhalation
Direct eye contact with paint may result in irritation.
Prolonged or repeated contact may cause skin irritation.
None
Every care has been taken to ensure the accuracy of the information contained in this data sheet, but no liability can be accepted arising from its
use. Where the conditions of use warrant it, it is recommended that the data are checked to ensure their suitability for the use envisaged.
Safety Data Sheet (SDS)
Product Name: SNO-COTE XGLO
REV: JUL 2014
Page: 2 of 3
SECTION 5: FIRST AID MEASURES
Ingestion
Eye Contact
Skin Contact
Inhalation
Immediately consult a doctor.
Immediately flush eyes with copious quantities of water for at least 15
minutes and consult a doctor.
Wash skin thoroughly with soap and water.
Remove to fresh air.
SECTION 6: FIRE FIGHTING MEASURES
Extinguishing Media
Special Hazards
Product is non-combustible; use extinguishing media appropriate for
surrounding fire.
Product components will not burn. If the temperature exceeds the boiling
point of the aqueous phase then splattering may occur.
SECTION 7: ACCIDENTAL RELEASE MEASURE
Personal Precautions
Cleaning
Appropriate protective equipment must be worn when handling a spill of
this material.
Spillage and leak should be absorbed using an inert material and
transferred to close containers for disposal. Contact local authority for
advice on disposal.
SECTION 8: HANDLING AND STORAGE
Handling
Storage
General room ventilation is expected to be satisfactory. Where direct
handling is necessitated personnel should always wear protective
clothing and gears such as facemask, gloves, safety goggles and
appropriate foot wear.
Always keep container in a proper upright position. Store product in cool,
well ventilated and dry place. Keep away from direct sunlight.
SECTION 9: EXPOSURE CONTROL AND PERSONAL PROTECTION
Exposure Limit
Respiratory Protection
Skin Protection
Eye Protection
Other Protective Equipment
None established, only applicable to trace components.
None required in well ventilated areas but if spraying applications are
involved appropriate mechanical extraction should be employed.
Gloves of impervious type.
Safety glasses.
Eye wash and emergency shower.
SECTION 10: STABILITY AND REACTIVITY
Conditions to Avoid
Materials to Avoid
Instability
Decomposition Products
None
None
0
The material is considered stable. Avoid temperature above 177 C, the
onset of polymer decomposition. Thermal decomposition is dependent
on time and temperature.
Carbon monoxide and/ or carbon dioxide.
SECTION 11: TOXICOLOGICAL INFORMATION
Toxicological Information
Information on analogous product shows minimal toxicity concerns.
Every care has been taken to ensure the accuracy of the information contained in this data sheet, but no liability can be accepted arising from its
use. Where the conditions of use warrant it, it is recommended that the data are checked to ensure their suitability for the use envisaged.
Safety Data Sheet (SDS)
Product Name: SNO-COTE XGLO
REV: JUL 2014
Additional information
Page: 3 of 3
Not applicable.
SECTION 12: ECOLOGICAL INFORMATION
Degradability
Environmental Risks
Some components are not biodegradable.
None to our knowledge
SECTION 13: DISPOSAL INFORMATION
Disposal of both material and container waste to be in accordance with applicable regional, national, and local laws
and regulations. Local regulations may be more stringent than regional or national requirements and must be
complied with.
SECTION 14: TRANSPORT INFORMATION
No classification is currently assigned.
SECTION 15: REGULATORY INFORMATION
Proposed Classification
Risk Phrases
Safety Phrases
Not hazardous
Not applicable
Not applicable
SECTION 16: OTHER INFORMATION
This product is intended for use in decorative and protective coating applications. For other uses, or where food
contact is involved, advice should be sought from Trans-Ocean Coatings & Chemicals Sdn Bhd.
<End of document>
Every care has been taken to ensure the accuracy of the information contained in this data sheet, but no liability can be accepted arising from its
use. Where the conditions of use warrant it, it is recommended that the data are checked to ensure their suitability for the use envisaged.