Fire Pumps Fire Pumps

Kap.04-01 20.02.2006 12:35 Uhr Seite 1

04

Kap.04-02 29.03.2005 10:37 Uhr Seite 4

FIRE PUMPS

04

ZIEGLER fire fighting centrifugal pumps - proven high quality

ZIEGLER fire pumps are powerful and wear-resistant centrifugal pumps, single or dual stage types, rugged, designed for dirty water, safe to operate and require very low maintenance. The simple functional construction, the easily legible gauges and the automatic engagement, priming and pressure control systems make the pump operation easy. Due to their design characteristics the

ZIEGLER fire pumps can be adapted to foreign standards without problems.

ZIEGLER fire pumps are made of highquality materials. The pump casing, diffusor, impellers and pump cover are of sea-water resistant light alloy. The pump shaft and split rings are made of stainless steel. Shaft sealing is by means of radial shaft sealing rings in an exchangeable sealing sleeve. The delivery outlets feature self-closing globe valves and ball valves in compliance with DIN-standard.

The capacity of a built-in vehicle pump depends on the rpm and power of the vehicle engine, arrangement of the pump unit as well as the conditions under which water is fed to the pump.

The pump charts on the following pages show performance curves measured under DIN requirements.

ZIEGLER rear mounted pumps rugged, powerful, extensible and of matured construction

ZIEGLER fire pumps for rear or midship mounting are available with performances of 750 up to 8000 l/min, suited for the power of the various vehicle engines. The rugged and neat construction makes our pumps reliable and permits an unobstructed and functional design of the vehicle pump bay, also in cases when complicated wiring and ducting systems are necessary, e.g. when a proportioning system or monitors are fitted.

ZIEGLER fire fighting centrifugal pumps are powerful: they have a high water performance at pressures of

20 bar and higher and through the connectable high-pressure pump a pressure of up to 40 bar can be reached.

ZIEGLER fire fighting centrifugal pumps are uncomplicated and easy to operate:

The fully automatic priming system

TROKOMAT PLUS simplifies the operation of the pump enormously.

On engaging the pump, priming takes place by operating the throttle only.

A button is pushed and the ZIEGLER

ANS-system provides automatic engagement of the PTO.

Our automatic constant pressure governor TOURMAT D facilitates the work of the operator. Any change of pressure is instantly sensed and the pump performance is adjusted accordingly within fractions of a second. Our flow-controlled foam concentrate proportioning system

PROFOMAT delivers exactly the desired concentration and provides simultaneous delivery of water or foam at the outlets.

Our modular operation and control system is designed and constructed for a modern extensive pump unit.

The performances of the pumps comply with DIN EN 1028 table 3.

The max. performance figures are values that are reached under optimum conditions on our pump test floor with the most simple water duct on suction and delivery side.

The pictures on the following pages may show details/versions that are available at additional costs.

The art. Nos. refer to the basic version of the various pumps only.

DIRECTION OF ROTATION:

All ZIEGLER fire pumps are available with clockwise or anticlockwise rotation.

Terms:

HL: Pump with anticlockwise rotation when looking at the pump cover.

HR: Pump with clockwise rotation when looking at the pump cover.

Pumps without gear multiplication : the pump direction of rotation and the rotation of the PTO flange are identical.

Pumps with gear multiplication: the pump direction of rotation is opposite to the direction the PTO flange.

2

Please note that all dimensions and weights noted in our catalogue are approximate values.

For orders please contact our local agent.

Kap.04-03 29.03.2005 10:38 Uhr Seite 5

VEHICLE MOUNTED PUMPS

MODULAR SYSTEM

ZIEGLER fire pumps - modular system

The renowned ZIEGLER pumps are not only available with various performance data. The fire pumps described on the following pages can be provided with various types of delivery outlets, with automatic engagement system and constant pressure control system as well as with various foam agent proportional systems.

The ever increasing number of modern high-tech electronic plants increases the need for a fire fighting technology that keeps the secondary water damage as low as possible. To this effect we deliver our fire pumps already equipped for retrofitting a high-pressure pump.

The well-proven and continuously improved ZIEGLER 3-stage highpressure pump is connected to the running normal-pressure pump via an electromagnetic clutch. The impellers of the HP-pump are not coupled to the shaft of the normal-pressure pump, i.e. they are not running when the normal-pressure pump is in operation.

This reduces the wear to a minimum and permits a relatively easy retrofit.

The operation of the high-pressure pump is simple:

When the connection line between normal-pressure pump and highpressure pump is opened, the electromagnetic clutch is actuated. Now open the delivery outlet to highpressure reel. A thermal relief line to the tank prevents overheating in case the water delivery is interrupted.

The unit can be operated in the following ways:

Normal-pressure pump operation

(HP-pump is not running)

High-pressure pump operation

(normal-pressure pump in circuit)

Combined pump operation

(both pumps are running)

3

04

Kap.04-04 29.03.2005 10:39 Uhr Seite 4

04

MODULAR OPERATION AND

CONTROL PANEL ”BKT”

”BKT” modular operation and control panel

Modules:

7 6 5 4 3 2 1

0 0 0 0 0 0

I

0 0

I I

0

1/4

0

1/2

3/4

1/1

214 174

1/4

0

1/2

3/4

1/1

214 174 max. 4 bar max. 1600 l/min

2

4

0

6 bar

10

8

0

I

6

4

8

10

12

14 bar

16

10

20

0

30

40

50 bar

60

0

I

-0,4

-0,6

-0,2

-0,8

-1 bar

0 5

10

25

15

20

5

0

10 15 bar

25

20

2

4 6

8

0 bar

10

10

20

0

30

RPM x 100

40

50

60

VDO

Module (control panel) Function

1 Main switch

2 Pump

3 High pressure

4 Tourmat D

5 Water

6 Foam/light mast

7 Loudspeaker e.g. main switch, rpm counter e.g. delivery pressure gauge, inlet pressure gauge, compr.-air gauge, pump switch ”ON/OFF”, rpm +/e.g. high pressure gauge, pilot lamp, switch for rapid intervention e.g. automatic constant pressure governor e.g. water tank level gauge, tank fill pressure gauge, switch for level adjustment e.g. foam tank level gauge/tumbler switch, spotlight adjustment e.g. switch ”ON/OFF”, hour counter

0 0 0 0 0 0

I

10

20

0

30 bar

40

50

60

I

0 0

2

4

0

6

8 bar

10

1/4

0

1/2

3/4

1/1

214 174

I

5

0

10 15 bar

25

20

N

-0,4

-0,6

-0,2

-0,8

-1 bar

0 5

10

25

15

20

0

10

0

20

30

RPM

40

50 x 100 60

VDO

6

8

10

12

14

4 bar

16

3 2 1

Module (control panel) Function

1 Main switch/

Tourmat D

2 Pump

3 High pressure/ foam e.g. main switch, rpm-counter,

Tourmat D, tank level gauge e.g. delivery pressure gauge, inlet pressure gauge, compr.-air gauge, pump switch ”ON/OFF”, rpm +/-, loudspeaker e.g. high pressure gauge, pilot lamp, switch for rapid intervention, hour counter, foam ”OPEN/CLOSED”

A few basic functions are described here.

Further additional functions are available on request.

4

Kap.04-05 29.03.2005 10:40 Uhr Seite 5

PRIMING SYSTEM

TROKOMAT PLUS

TROKOMAT PLUS – the automatic priming system that sets standards.

Design and mode of operation:

The ZIEGLER TROKOMAT PLUS is a modern reciprocating priming pump that carries out the priming action fully automatically, thus simplifying the pump operation to a minimum. The

TROKOMAT PLUS operates without any auxiliary fluids such as water or oil.

The TROKOMAT PLUS is switched on and off hydraulically by means of water pressure and no other control is required. The automatic process is carried out by very few parts (pic. 1): this makes the TROKOMAT PLUS reliable and increases its durability.

Even at low engine rpm the

TROKOMAT PLUS starts the suction action. This reduces wear on the engine, especially when starting from cold. The fully automatic priming system TROKOMAT PLUS consists of two completely separately working short-stroke reciprocating pumps.

The pistons are pressed by a spring against an eccentric pump shaft. If the pump is engaged, the rotating eccentric pump shaft presses the pistons alternatively outwards. During this action air is drawn in from the suction line and housing. The springs press the pistons back towards the eccentric shaft. At the same time the intake air is compressed and routed to the atmosphere (pic. 2). The water entering into the primed pump overcomes the spring pressure and thus disengages the pistons from the eccentric shaft. TROKOMAT PLUS switches off (pic. 3). If the pump pressure drops, the springs press the pistons against the eccentric shaft again and the priming resumes. The pump operator simply has to engage the pump and open the throttle.

A further essential advantage:

We install the ZIEGLER TROKOMAT

PLUS in all vehicle fire pumps and in all portable pumps from type TS 5/6 onwards, i.e. in all these types of pumps TROKOMAT PLUS parts and functions are identical.

Picture 1

Picture 2

Venting stroke

Picture 3

3 7 1

•

•

4 6 8 2

3 7 1 9

•

4 6 2

01 Bearing flange

02 Piston complete

03 Pressure spring

04 Cylinder cap

05 Hexagon screw

06 Inlet membrane

07 Outlet membrane

08 Leaking water bore

09 Reengagement valve

•

1 2

Working position

Eccentric

Stand-by position

Eccentric

3 4

1 7

•

•

•

2 8 6 4

9 1 7 3

•

2 6 4

3

5

Suction stroke

TROKOMAT PLUS is patented, patent No.: P 196 00 641.1.

04

5

Kap.04-06 29.03.2005 10:41 Uhr Seite 6

AUTOMATIC PTO ENGAGEMENT SYSTEM ”ANS”

AUTOMATIC PRESSURE GOVERNOR

”TOURMAT D”

0 0 0 0 0 0

4

0

I

1/2

1/4 3/4

0

Inhalt content

214 174

1/1

1/2

1/4 3/4

0

Inhalt content

214 174

1/1 max. 4 bar max. 1600 l/min

2

4

0

6

8 bar

10

0

I

6

8

10

12

14

4 bar

16

10

20

0

30 bar

60

40

50

-0,4

-0,6

-0,8

-1

-0,2 bar

0 5

10

25

15

20

5

0

10 15

20 bar

25

2

4 6

8

0 bar

10

20

30

RPM

10

0 x 100

VDO

60

40

50

7 8 12 6 5

Control module chassis

Control module

ZIEGLER

04

2 1

11

10

9

3

ANS/TOURMAT D with electronic injection EDC

The pressure governor TOURMAT D (1) is an automatic pump pressure control for ZIEGLER centrifugal fire pumps (3).

Pressure fluctuations which may occur due to different water delivery, e.g.

when connecting or disconnecting nozzles, are instantly sensed and immediately corrected. The desired pump pressure is set by means of a rotary knob (8). The max. possible quantity of water is shown in the pump performance diagram. All controls are clearly arranged on the BKT (operation and control panel) (4).

Mode of operation:

When the main switch (5) (option) and the pump ”ON” button (6) are pressed, the PTO is engaged via the fully automatic ZIEGLER ”ANS” system.

Now the TOURMAT D electronic system can be activated by pressing the button ”Automatic” (7).

The preset pressure (rotary knob) (8) is compared with the pressure measured at the pump (9). If the pump pressure is less than 3 bar and the water head is not built-up or raptured respectively, suction is started. The electronic system switches over to rpm control and the optimum pump rpm for suction is set. The rpm sensor mounted on the pump flange (10) shows the actual value of the pump rpm. If the pressure of 3 bar is exceeded, the control circuit acts as pressure governor. If the pump pressure is lower or higher than the set pressure, the control circuit directly acts on the electronic speed adjustment of the vehicle (2) until the desired pressure is reached. If the automatic system (7) or the pump is switched off

(6), the rpm is automatically adjusted to idling.

1. Control module TOURMAT D

2. Control module chassis

3. Fire pump

4. BKT control panel

5. Push button - main switch

6. Push button - pump ”ON/OFF”

7. Push button - automatic

TOURMAT D

8. Rotary knob - pump pressure

9. Pressure sensor

10. Rpm sensor

11. Chassis engine

12. Push button ”Gas +/-” (manual adjustment)

If the automatic system is in operation and one of the buttons ”rpm+/-” (12) is pressed, the TOURMAT D (automatic) is switched off. The pressure adjustment is now done manually. To avoid operating errors the pump rpm can be changed only if the pump is engaged and the handbrake is actuated.

This is also the case in emergency operations.

Advantages:

Due to the electronic system of

TOURMAT D the pump operator does not need to check or adjust controls.

The pressure is constant even if water delivery is changed.

6

Kap.04-07 29.03.2005 10:42 Uhr Seite 7

AUTOMATIC PTO ENGAGEMENT SYSTEM ”ANS”

FREQUENCY GOVERNING

SYSTEM “TOURMAT F”

ANS system

This is an electronic system for switching on the generator. By means of a push button all processes for switching on and off the generator run automatically. Irrespective of the standard PTO engagement system in the driver’s cab the generator can be engaged in the generator box.

Description of the PTO engagement system ANS:

ANS and TOURMAT F with electronic injection pump

TOURMAT F (1) is a fully automatic frequency governing system with a constant frequency - usually 50 Hz for use with a built-in generator (7).

The controls are mounted in the generator box (3). The push button (4)

”generator ON/OFF” activates the electronic system, which automatically engages the PTO.

The rpm sensor (5) in the PTO flange signals to the control that the generator is in operating condition.

The frequency governor is now activated via the electronic rpm adjustment (2) of the vehicle.

In this way a constant power supply is ensured even if the consuming devices are changed.

In case of an emergency an alteration of the generator frequency can take place in the driver’s cab in vehicles with electronic speed adjustment.

When the generator is switched off the rpm is automatically adjusted to idling and the PTO is disengaged.

3

4

EIN/AUS

Control module chassis

2

6

1. Control module TOURMAT F

2. Control module chassis

3. Generator box

4. Push button - generator ”ON/OFF“

5. Rpm sensor

6. Chassis engine

7. Built-in generator

Control module

ZIEGLER

1

5

7

04

7

Kap.04-08 29.03.2005 10:43 Uhr Seite 8

04

FOAM PROPORTIONING

SYSTEM ZZ

ZIEGLER foam proportioning units the most modern and extensive range on the market!

ZZ ZIEGLER ejector pump proportioner for the feed water line

A decrease of the pipe diameter causes a negative pressure that draws in the foam agent.

Advantages:

+ simultaneous delivery of water or foam at the outlets

+ independent of source of water supply to the pump

+ foam can be drawn also from external sources

Disadvantages:

- pressure loss of 30%

- the throughput of the proportioner must be identical with the consumption of the consuming devices

- sensitive to counter-pressure resulting from friction

8

4

2

7

6 %

0 %

2 %

4 %

6

1

5 3

1. Water tank

2. Foam tank

3. Suction line water tank

4. Suction line foam tank

5. Fire pump

6. Delivery outlets

7. ”Z” proportioner

8. Pressure hose

8

Kap.04-09 29.03.2005 10:46 Uhr Seite 9


SYSTEM ZPV

ZPV ZIEGLER pump proportioner

ZPV is a proportioning unit that works on the ejector pump principle. The foam concentrate is drawn in and added to the water on the suction side of the pump. The quantity of foam concentrate is set by means of a dosage lever.

ZIEGLER PVs are available in the following sizes: 50, 75, 100, 150, 200,

300, 400, 500 and 600 l/min.

Advantages (ejector pump principle):

+ thorough mixing

+ independent of counter-pressure

+ simple, reliable and low-priced proportioning system

Disadvantages

(ejector pump principle):

- changes in volume of flow require manual resetting

- when using water from a hydrant the delivery pressure must be 2.5 times higher

- complete pump unit must be flushed

- decrease of delivery performance due to by-pass line

6

2

4

9

0

50

100

150

200 l/min

04

8

1. Water tank

2. Foam tank



5. Fire pump

6. Delivery outlets

7. Pump proportioner

8. By-pass line

9. Dosage regulating device

5

7

3

1

9

Kap.04-10 29.03.2005 10:47 Uhr Seite 10


SYSTEM ZPV MAD

04

ZPV MAD

ZIEGLER pump proportioner with a mechanic-automatic dosage unit

The unit consists of a flow controlled proportioning governor and a proportioner. With this unit an automatic control of the quantity of foam concentrate is achieved. 3 different proportioning rates between 1 and 8% can be set.

MAD reacts quickly on changes of flow and always delivers exactly the required quantity of foam concentrate to the ejector pump for maintaining the selected percentage of foam.

ZPV MAD is available in two sizes:

- ZPV MAD 30 for flow rates of

100 - 3000 l/min

- ZPV MAD 50 for flow rates of

200 - 5000 l/min,

(even up to 6000 l/min if rate is reduced to 6%)

6

4

2

9

1%

3%

6%

Sp

10

8

5

7

3

1

1. Water tank

2. Foam tank



5. Fire pump

6. Delivery outlets


8. By-pass line

9. Mechanic-automatic dosage unit

MAD

10. Proportioning rate setting lever

10

Kap.04-11 29.03.2005 10:47 Uhr Seite 11

FOAM PROPORTIONING SYSTEM

ZPV EAD 80

1. Water tank

2. Foam tank



5. Fire pump

6. Delivery outlets


8. By-pass line

9. Flow meter water/foam mixture

10. Dosage unit

11. Flow meter foam concentrate

ZPV EAD 80

ZIEGLER pump proportioner with an electronic-automatic dosage unit

The unit consists of a magneticinductive flow meter in the pressure line of the fire pump, a further magnetic-inductive flow meter as well as an electrically controlled dosage unit in the foam suction line of the pump proportioner.

The foam concentrate is aspirated via a pump proportioner and fed into the suction line of the fire pump. A SPS controlling device evaluates the signals from the flow meters and adjusts the dosage unit in accordance with the preset proportioning rate.

Range of water flow:

- 100 - 8000 l/min

Range of foam flow:

- 1 - 700 l/min

Proportioning rates:

- 1% - 8%

9

6

1 %

3 %

6 %

SP

SPS

4

M

2

10

11

04

8

1 7

5

3

11

Kap.04-12 29.03.2005 10:48 Uhr Seite 12

FOAM PROPORTIONING SYSTEM

PROFOMAT

04

PROFOMAT

The self-regulating pressure proportioning system

The PROFOMAT pressure proportioning system is used for automatic and exact proportioning of foam concentrate over the full range of outgoing flows and pressures of water delivery by fire pumps. The PROFOMAT system consists of one or several proportioners, dosage unit with setting dial, pressure regulator, non-return valve to the foam tank and a foam concentrate pump. The proportioner/s is/are mounted on the delivery side of the pump. The delivery water flows through the proportioner/s. By means of the dosage unit the desired proportioning rate for the foam concentrate can be set manually or by remote control. The foam concentrate is pumped to the proportioner by the foam concentrate pump via a pressure regulator.

The pressure of the foam concentrate must be at least 2 bar higher than the corresponding delivery pressure. In the pressure regulator the difference between the water pressure and the foam concentrate pressure is mechanically controlled by means of a membrane. The foam concentrate flowing through the pressure regulator and the dosage unit is mixed to the delivery water via the proportioners at a preselected rate.

Advantages/characteristics: a) Irrespective of the flow and pressure of the water delivered by the fire pump the proportioning rate remains constant as long as the pressure of the foam concentrate is at least 2 bar higher than the water pressure. The performance of the fire pump and the foam concentrate pump must only meet the requirements of the largest consuming device (monitor).

b) If necessary, a proportioner can be provided for each consuming device

(delivery outlets, monitors, body/ ground protection unit etc.). In such cases the proportioner is designed for the max. delivery required.

c) If individual proportioners are provided for each consuming device, they can, independed of each other, be fed with water or foam concentrate solution at variable proportioning rates, suitable for each consuming device.

d) Continuous adjustment of the proportioning rate is possible.

e) As no moving parts are used the system is resistant to wear and almost maintenance-free.

Applications:

- water/foam vehicles for refineries and for protection of industrial plants

- decentralized proportioning in stationary foam systems in refineries and tank farms

8

2

11

6

9

6

9

6

9

6

10

7

5

4

1

3

1. Water tank

2. Foam tank



5. Fire pump

6. Delivery outlets

7. Foam concentrate pump

8. Proportioning system

PROFOMAT 50

9. Proportioning system

PROFOMAT 12

10. Water delivery line

11. Foam delivery line

12

Kap.04-13 29.03.2005 10:49 Uhr Seite 11

COMPRESSED AIR

PROPORTIONING SYSTEMS AND

COMPRESSED AIR FOAM SYSTEMS

ZIEGLER FOAM SYSTEM (Class A)

ZIEGLER POWER FOAM BASIC NA (Class A and Class B as required)

ZIEGLER POWER FOAM PRO (Class A and Class B as required)

ZIEGLER unit

Foam System 1 E

Foam System 2 E

Power Foam

Basic NA

Power Foam

Pro 1

Power Foam

Pro 2

Max.

flow delivery water/foam

1200 l/min

1600 l/min

1200 l/min

1600 l/min

2400 l/min

Foam agent pump delivery max. foam

9,6 l/min

24 l/min

9,6 l/min

19 l/min

19 l/min

Max.

adjustable proportioning rate

6%

6%

6%

10%

10%

Compressor delivery air

(nominal output) without without

Remarks new standard

DIN V 14430

DZA 4 / 0.2 - 2.4

DZA 8 / 0.2 - 3.0

DZA 16 / 0.2 - 1.5

DLS 4 1400 l/min

7 bar

2500 l/min

10 bar

5400 l/min

10 bar

DLS 8

DLS 16

04

13

Kap.04-14 29.03.2005 10:50 Uhr Seite 14

FOAM SYSTEM 1 E

COMPRESSED AIR PROPORTIONING SYSTEM

DZA 4 / 0.2 - 2.4

04

ZIEGLER FOAM SYSTEM 1 E for generating class A foam with class

A foam agent and nozzles

(CM nozzles, fog nozzles etc.) with a nominal performance of 400 l/min at a proportioning rate of 0.2 - 2.4%. A delivery of up to 1200 l/min water/ foam mixture is possible.

The proportioning rate is adjustable irrespective of the amount of water delivered.

Foam can be generated with use of foam nozzles (S2 - S4 and M2 - M4 respectively) and universal or class B foam agent.

The system can be used in all types of vehicle with a FPN or portable pump.

We recommend vehicles with FPN and integrated tank.

The system can be used with:

TSF-W with TS 8/8, vehicles with FPN 10-1000

(e.g. LF 10/6) up to FPN 10-2000

(e.g. LF 20 / 16 or TLF 16).

Foam delivery can take place via one or more hoses or a monitor. Fog nozzles have turned out to be the most advantageous nozzles when using class A foam. The use of fog nozzles supports the generating of small drops.

ZIEGLER FOAM SYSTEM 1 E consists of:

• Foam pump (9.6 l/min)

• Foam supply from cans, from onechamber foam agent tank (e.g. 60 l) or from two-chamber tank

(e.g. 50 l/100 l)

• Flow meter water

• Flow meter foam

• Operating elements

(display and emergency operation)

• Display indicating:

- Water flow

- Foam flow

- Proportioning rate adjustable during action in %

- Total water consumption

- Total foam consumption

• Manual emergency operation for foam via rotary button

• Connection of the foam unit to the pump pressure line

• Electric wiring

• Special foam can lid with connections for ventilation and with foam filter

• Inlet and outlet via 1 size B Storz

• Operating elements on pump operating panel

• with tank change-over in case of a zwo-chamber tank

Technical data:

Foam pump: 9.6 l/min

Nominal performance: 400 l/min at a proportioning rate of

0.2 - 2.4%

Volume flow: up to 1200 l/min

(max. proportioning rate = 0.8%)

Proportioning rate: 0.2 up to 6%

(max. volume flow reduction at

6% = 160 l/min)

also for retrofitting

!

FULFILLS EVEN THE REQUIREMENTS

OF A DZA 8 / 0,2 - 1,2

(NOMINAL PERFORMANCE 800 l/min)

7.0

6.0

5.0

4.0

3.0

2.0

1.0

0

DZA 4/0.2-2.4

Capacity foam pump

400 l/min - 2.4 %

100 200 300 400 500 600 700 800 900 1000 1100 1200 1300

Qw (l/min)

14

Kap.04-15 29.03.2005 10:51 Uhr Seite 15

FOAM SYSTEM 2 E

COMPRESSED AIR PROPORTIONING SYSTEM

DZA 8 / 0.2 - 3.0

ZIEGLER - FOAM SYSTEM 2 E for generating class A foam with class A foam agent and nozzles (e.g.

CM nozzles, fog nozzles etc.) with a nominal performance of 800 l/min at a proportioning rate of 0.2 - 3.0%. A delivery of up to 1600 l/min water/ foam mixture is possible. The proportioning rate is adjustable irrespective of the amount of water delivered. Foam can be generated with the use of foam nozzles (S2 - S4 and M2 - M4 respectively) and universal or class B foam agents.

The unit is suitable for use in any type of vehicle with a FPN.

The system can be used in vehicles with

FPN 10-1000 (e.g. LF 10/6) up to

FPN 10-2000 (e.g. LF 20/16 or

TLF 16).

Either up to 6 nozzles (C, M4, S4) or a monitor can be used.

Fog nozzles have turned out to be the most advantageous nozzles for use with class A foam. They support the generating of small drops.

ZIEGLER FOAM SYSTEM 2 E consists of:

• Foam pump (24 l/min)

• Foam supply from two-chamber foam agent tank (e.g. 50/100 l)

• Flow meter water

• Flow meter foam

• Connection of the foam unit to the pump pressure line

• Operating elements

(display and emergency operation)

• Display indicating:

- Water flow

- Foam flow

- Proportioning rate adjustable during action in %

- Total water consumption

- Total foam consumption

• Manual emergency operation for foam via rotary button

• Electric wiring

• 2 outlets size B Storz

• Operating elements on pump operating panel

Technical data:

Foam pump: 24 l/min

Nominal performance: 800 l/min at a proportioning rate of

0.2 - 3.0%

Volume flow: up to 1600 l/min

(max. proportioning rate = 1.5%

Proportioning rate: 0.2 - 6%

(max. volume flow reduction at 6% = 400 l/min)

04

FULFILLS EVEN THE REQUIREMENTS

OF A DZA 16 / 0.2 - 1.5

(NOMINAL PERFORMANCE 1600 l/min)

7.0

6.0

5.0

4.0

3.0

2.0

1.0

0

DZA 8/0.2-3.0

Capacity foam pump

800 l/min - 3.0 %

Qw (l/min)

15

Kap.04-16 29.03.2005 10:52 Uhr Seite 16

POWER FOAM

BASIC NA

B

1/4

1/2

0

3/4

1/1

A

1/4

1/2

0

3/4

1/1

2

4

0

6

8 bar

10

ON

OFF

0 0 0 0 0 0

04

ZIEGLER POWER FOAM BASIC NA

With ZIEGLER units with CAFS a throw of up to 30-50 m is possible.

The performance of the compressor is 1400 l/min at 7 bar.

The volume flow is up to 1200 l/min water/foam mixture at a proportioning rate of 0.2 - 6% and compr.-air foam with additionally up to 1400 l/min compr.-air.

Foam quality adjustable:

Volume ratio water/foam mixture to air wet: 3 ≤ Vv ≤ 10 dry: 10 < Vv ≤ 15

The unit is operated with a working pressure of up to max. 7 bar.

The proportioning is adjustable from

0.2 to 6% via a push button and adjusts automatically to the varying volume flows.

The system is very clear and easy to operate. By pushing a button the unit, also during operation, can be switched over from water to CAFS action or the other way round.

Simultaneous use of 3 size B nozzles with class A foam or 3 size C nozzles with compr.-air foam and the use of a monitor respectively is possible without problems. Other combinations such as water delivery via delivery outlets with 2 size C hoses and simultaneous CAFS action with one outlet are also possible.

All CAFS components are found in one and the same equipment locker.

The system requires very little maintenance. In case of service the complete BKT (operating and control panel) can be swung to the side and all important parts are clearly shown.

The unit is of such a low weight that it can be installed in every ZIEGLER

LF 10/6. The ZIEGLER Power Foam

Basic NA can, from the performance spectrum point of view, be used in every vehicle with a FPN 10-1000 or a FPN 10-2000.

COMPRESSED AIR FOAM DLS/CAFS

DLS

COMPRESSED AIR PROPORTIONING SYSTEM

DLS

(DIN V 14430)

Performance:

- 400 l/min water/foam mixture

- Proportioning rate = 0.2 - 2.4%

- 1400 l/min compressed air at 7 bar

- Volume ratio air/foam = 3 - 15

16

Kap.04-17 29.03.2005 10:54 Uhr Seite 17

DLS


Fire pump 2

Water line 1

Foam line

6

4

Control technique

Foam pump 3

Compressor

5

Pump operation panel with POWER FOAM BASIC NA wet/dry

9

7 Air line

8

Air regulating valve

10

Water/foam/air mixture

Schematic picture DLS/CAFS for POWER FOAM BASIC NA

04

Technical data:

Foam pump: max. 9.6 l/min at 17 bar

Compressor performance: max. 1400 l/min at 7 bar

Working pressure of system:

7 bar

Flow meter 2”- Measuring range:

60 - 1200 l/min

Drive of compressor:

PTO, via belt drive with magneto coupling

Power required by compressor: max. 9 kW

Other configurations of

ZIEGLER class A foam systems and DLS units with ZIEGLER centrifugal fire pumps are possible!

We will be pleased to give you further information.

POWER FOAM BASIC NA

17

Kap.04-18 29.03.2005 10:55 Uhr Seite 18

+

-

B

1/4

1/2

0

3/4

1/1

A

1/4

1/2

0

3/4

1/1

Max

Auslastung

Fluß l/min %

Total

Wasser Schaum

Auswahl

ON

Auswahl

%

Achtung! Betriebsanleitung lesen und beachten.

POWER FOAM PRO

LUFT-

ZUMISCHUNG

Luftmengenanzeige

Achtung! Betriebsanleitung lesen und beachten.

gefördert werden!

Schaumzumischung am ARC regeln.

Luft bereit

ON

HVC

TEMP

HVC

HOURS

Öltemperatur Betriebsstunden

Keine Blindkupplungen an den CAFS-Abgängen anbringen!

5

10

15

20

25

0 bar

30

AIR / LUFT

WATER / WASSER

04

ZIEGLER POWER FOAM PRO 1 for the generation of class A foam up to 1600 l/min at a proportioning rate of 0.1 - 10% and compr.-air foam with additionally up to

2500 l/min compr.-air.

Foam quality adjustable for PRO 1 and

PRO 2:


The set proportioning rates automatically adjust to the varying volume flows.

ZIEGLER POWER FOAM PRO 1 unit is suitable for installing in every vehicle with a FPN 10-1000 or a

FPN 10-2000 . Simultaneous use of

6 size C nozzles with class A foam or compr.-air foam and the use of a monitor respectively is possible.

ZIEGLER POWER FOAM PRO 1 system consists of:

• ZIEGLER centrifugal fire pump for delivery of the necessary extinguishing water

• Foam proportioning system with foam pump, flow meter, foam tanks, foam agent injection nozzle, electropneumatic selector valve for choice of foam agent with flush adjustment, foam agent filter and non-return valves

• Operating panel with indicator for current volume flow, proportioning rate, water and foam agent consumption as well as utilization

• HVC compressor with separator tank and oil cooler

• Compr.-air control valve with manual emergency control

• Automatic measuring and control unit for the air volume with air volume indicator

• ARC control unit for foaming control (wet/dry)

Technical data:

Geared foam pump:

19 l/min at 17 bar

Compressor performance:

2500 l/min at 10 bar

Compressor drive:

PTO, via belt drive with magneto coupling

Flow meter 2” measuring range:

60 - 1600 l/min

Foam pump engine:

24 V, 0.5 kW

Power required for compressor: max. 37 kW



DLS

(DIN V 14430)

Performance:


- Proportioning rate = 0.3 - 2%

- 2500 l/min compr.-air at 10 bar


18

Kap.04-19 29.03.2005 10:56 Uhr Seite 19

Pump operation panel with POWER FOAM PRO

ZIEGLER POWER FOAM PRO 2 for the generation of class A foam up to 2400 l/min at a proportioning rate of 0.1 - 10% and compr.-air foam with additionally up to

5400 l/min compr.-air. Foam quality adjustable for PRO 1 and PRO 2:


The set proportioning rates adjust automatically to the varying volume flows.

ZIEGLER POWER FOAM PRO 2 system is suitable for installation in every vehicle with a FPN 10-1000 or a FPN 10-2000. Simultaneous use of

6 size C nozzles with class A foam or compr.-air foam and additionally use of a monitor is possible.

Fire pump 2

Water line 1

Foam line

6

4

Control technique

Foam pump 3

Compressor

5 wet/dry

9

7 Air line

8 Air regulating valve

10

Water/foam/air mixture

Schematic picture DLS/CAFS for POWER FOAM PRO

04

ZIEGLER POWER FOAM PRO 2 system consists of the same components as the POWER FOAM PRO 1 system, but with the following deviating performance figures:

Compressor performance:

5400 l/min at 10 bar

Flow meter 2.5” measuring range:

60 - 2450 l/min

Please contact us for further information!


DLS

(DIN V 14430)

Performance:


- Proportioning rate = 0.3 - 1%

- 5400 l/min compr.-air at 10 bar


19

Kap.04-20 29.03.2005 10:57 Uhr Seite 20

HIGH PRESSURE EXTINGUISHING UNITS

04

59301

The principle

Efficient fire fighting with optimum use of the extinguishing power of water.

Through the fine atomization an almost complete vaporization of the water is reached. The oxygen concentration and the oxygen supply respectively is obstructed and an optimum cooling effect is obtained.

Range of application

The high pressure extinguishing device

HDL is used when fighting fires of class A and B. For fires of class A

(hard substances fires) the classical extinguishing agent water is predominantly used. Depending on requirement and situation a changeover to foam can take place through admixing of foam agent and the quick and easy engagement of the rapid intervention unit. Foam is an excellent medium for extinguishing fires of combustible liquids (fire class B) and prevents possible backfires at hard substances fires.

Advantages:

- Compact rapid intervention unit

- Optimum use of the cooling effect of water

- Suffocating effect through water vaporization

- Minimum water consumption, max. 25 l/min

- Reduction of water damage

- Admixing of foam agent only when necessary

- Multifunctional in connection with further components (“Ölblitz” road cleaner, mud collector, etc.)

High pressure extinguishing device

HDL 250

Mobile unit with tank of 125 l with rugged steel pipe frame/chassis, canister holder and push bar. Drive by 2-cyl. V petrol engine, 13.2 kW

(18 HP). Oil pressure control, vibrationresistant starter battery 12 V/44 Ah, electric starter, emergency pull starter.

Exchangeable canister tank of 5 l for standard petrol. Power transmission through oil bath lubricated reduction gear 3600:1450 rpm, 3-cyl. piston pump, oil bath lubricated, with wearresistant ceramic plungers, stainless steel valves, chem. nickel-plated, corrosion-resistant brass cylinder head. Water filter with stainless steel sieve. High pressure control valve with pressure relief for closed extinguishing pistol. Overheating protection through a thermovalve 58° C. Glycerol damped manometer 0 - 400 bar (class 1.6).

Hose drum, rotating under full pressure, for 60 m of armored hose

(600 bar) with crank, hose reel window and brake. Foam agent suction device

3% with shut-off valve. With 50 m of armored hose (600 bar), hose detwisting joint, self-closing lockable extinguishing pistol. Combination extinguishing adaptor (corrosionresistant) adjustable from high pressure fog to low-expansion foam.

Water delivery: max. 24 l/min

Working pressure: 280 bar

Extinguishing water pressure: 250 bar

Dim. (LxWxH): 1210x760x1100 mm

Weight (empty): 177 kg

...................................................

59301


HDL 250

Portable pump version with tank of

125 l * as art. No. 59301, but without chassis, canister holder and push bar. With frame for portable pump rail. Carrying handles and battery charging socket complying with DIN 14690.



...................................................

59302

59304


HDL 170 S

Built-in version without tank with rugged mounting platform and metal rubber buffers for permanent mounting. Drive by 1-cyl. petrol engine

9.6 kW. Oil pressure control, vibrationresistant pull starter. Tank of 5 l for standard petrol. 3-cyl. piston pump, oil-bath lubricated, with wear-resistant ceramic plungers, stainless steel valves. Chem. nickel-plated, corrosionresistant brass cylinder head. Water filter with stainless steel sieve. High pressure control valve with pressure relief for closed extinguishing pistol.

Glycerol damped manometer

0 - 250 bar (class 1.6). Hose drum, rotating under full pressure, with 50 m of high pressure hose (300 bar) with crank and brake. Foam agent suction device 3% with shut-off valve. With hose detwisting joint, self-closing lockable extinguishing pistol.

Combination extinguishing adaptor

(corrosion-resistant) adjustable from high pressure fog to low-expansion foam.

Water delivery: max. 21 l/min

Working pressure: 180 bar

Extinguishing water pressure: 170 bar



...................................................

59304

Long-throw high pressure nozzle for high pressure extinguishing device * screw-on nozzle for effective throws of up to 7 m.

...................................................

59306

Further high pressure extinguishing devices on request!

* not illustrated

20

Kap.04-21 29.03.2005 11:10 Uhr Seite 13

AUTOMATIC WATER SUPPLY

SYSTEM AWZ

7 3

1

6

4 5

2

AWZ automatic water supply system

Purpose:

The purpose of the AWZ system is to supply the pump with water from a hydrant. It automatically feeds the pump with hydrant water, stopping the flow from the tank. A collecting head or transition piece at the suction inlet is not needed. Contraction of the hose when the throughput of water is too high is also prevented.

Function:

The system consists of two springloaded non-return valves. The valve (1) is placed in the tank suction line and has a very low opening pressure. The valve (2) is placed in a branch to the tank suction line, that ends between valve (1) and the pump. The valve (2) has a strong spring and is therefore not opened until the difference in pressure is 1 bar.

Water supply from the tank:

When water is supplied from the tank the valve (1) in the tank suction line opens. The valve (2) in the feed line from the hydrant remains closed due to the high spring tension. In this way no air is drawn in via the valve (2).

Water supply from hydrant:

When the feed line from the hydrant is pressurized so that the water pressure in front of the valve (2) increases to

1.5 bar or above, the valve (2) opens and water flows from the hydrant into the tank suction line. Through this water flow excess pressure is built up in the tank suction line and the valve (1) closes. In this way there is an automatic switch-over from supply from the water tank to supply from the hydrant.

Performance:

The quantity of water fed via the

AWZ system depends mainly on the capacity of the hydrant. The decisive factors are the nominal width and the existing water pressure. At a flow pressure of 1.5 bar to 2.0 bar in front of the valve (2) up to 1200 l/min can be reached.

1. Non-return valve

2. Non-return valve

3. Tank

4. Suction inlet

5. Hydrant inlet

6. Butterfly valve

7. Fire pump

21

04

Kap.04-22 29.03.2005 11:14 Uhr Seite 22

CENTRIFUGAL FIRE PUMP

FPN 10 - 750 - 2 H

04

18

16

14

12

10

8

6

4

2

delivery rate Q (l/min)

750

0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 points of guarantee: geod. suction height 3 m geod. suction height 7.5 m

(Test floor performance complying with DIN EN 1028)

FPN 10 - 750 - 2 H and

FPH 40 - 250 - 3

All FPN can be retrofitted with a

HP-pump.

Please see page 38, HP-pump.

22

FPN 10 - 750 - 2 H

Approv. No. AZ 100720403

ZIEGLER fire pump

(rear-mounted) for vehicle PTO of

62 kW (85 HP) onwards

Nominal pump output:

750 l/min at 10 bar and 3 m geod. suction height

Max. pump output:

(test floor performance complying with

DIN EN 1028)

1900 l/min at 10 bar and 3 m geod.

suction height

2100 l/min at 8 bar and 1.5 m geod.

suction height

Drive:

Via joint shafts from the PTO of the vehicle

Basic fittings:

Dual stage centrifugal fire pump, clockwise or anticlockwise rotation, with 1 size A suction inlet, 2 size B delivery outlets, 1 connection for rapid intervention line, 1 connection for tank fill line, 1 connection for tank suction line (lockable by means of a butterfly valve)

Priming system:

TROKOMAT PLUS, fully automatic

Gauges and controls:

Modular operation and control panel

BKT, please see page 4

Colour: Silver RAL 9006


Weight: 76 kg

Additional fittings (options):

2 more delivery outlets, connection for another rapid intervention line, monitor connection, fitting of a pump proportioner

Additional systems (options):

ANS, TOURMAT D, AWZ system,

TROKOMAT shut-off, draining device

Anticlockwise FPN 10 - 750 - 2 HL

(rotation, please see page 2)

.................................................

169352

Clockwise FPN 10 - 750 - 2 HR


.................................................

169485

Anticlockwise FPN 10 - 750 - 2 HHL


.................................................

156542

Clockwise FPN 10 - 750 - 2 HHR


.................................................

156544

Kap.04-23 29.03.2005 11:15 Uhr Seite 13


FPN 10 - 1000 - 2 H

FPN 10 - 1000 - 2 H







suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:

Dual stage centrifugal fire pump, clockwise or anticlockwise rotation, with 1 size A suction inlet, 2 size B pressure outlets, 1 connection for rapid intervention line, 1 connection for tank fill line, 1 connection for tank suction line (lockable by means of a butterfly valve)

Priming system:







Weight: 76 kg








.................................................

169352



.................................................

169485



.................................................

156542



.................................................

156544

18


10

8

6

4

2

16

14

12



FPN 10 - 1000 - 2 H and

FPH 40 - 250 - 3


HP-pump.


23

04

Kap.04-24 29.03.2005 11:16 Uhr Seite 30


FPN 10 - 1500 - 1 H

04


HP-pump.


24

18


12

10

8

16

14

6

4

2

0 300 600 900 1200 1500 1800 2100 2400 2700 3000 points of guarantee: geod. suction height 3 m geod. suction height 7.5 m


FPN 10 - 1500 - 1 H and

FPH 40 - 250 - 3

FPN 10 - 1500 - 1 H







suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:

Single stage centrifugal fire pump, clockwise or anticlockwise rotation, with 1 size A suction inlet, 2 size B delivery outlets, 1 connection for rapid intervention line, 1 connection for tank fill line, 1 connection for tank suction line (lockable by means of a butterfly valve)

Priming system:







Weight: 90 kg





TROKOMAT shut-off, MAD 30, draining device



.................................................

168987



.................................................

169106



.................................................

156546


(rotation, please see 2)

.................................................

156548

Kap.04-25 29.03.2005 11:16 Uhr Seite 29


FPN 10 - 1500 - 2 H

FPN 10 - 1500 - 2 H







suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:


Priming system:







Weight: 115 kg








.................................................

169290



.................................................

169724



.................................................

156549



.................................................

156550

18


12

10

8

16

14

6

4

2



FPN 10 - 1500 - 2 H and

FPH 40 - 250 - 3


HP-pump.


25

04

Kap.04-26 29.03.2005 11:17 Uhr Seite 30


FPN 10 - 2000 - 1 H

04


HP-pump.


26

18


12

10

8

6

16

14

4

2

2000



FPN 10 - 2000 - 1 H and

FPH 40 - 250 - 3

FPN 10 - 2000 - 1 H



(rear mounted) for vehicle PTO of




suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:


Priming system:







Weight: 90 kg








.................................................

168987



.................................................

169106



.................................................

156546



.................................................

156548

Kap.04-27 29.03.2005 11:18 Uhr Seite 29


FPN 10 - 2000 - 2 H

FPN 10 - 2000 - 2 H







suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:


Priming system:







Weight: 115 kg








.................................................

169290



.................................................

169724



.................................................

156549



.................................................

156550

14

12

10

8

6

4

2

18

16


0 300 600 900 1200 1500

2000

1800 2100 2400 2700 3000 points of guarantee: geod. suction height 3 m geod. suction height 7,5 m


FPN 10 - 2000 - 2 H and

FPH 40 - 250 - 3


HP-pump.


27

04

Kap.04-28 29.03.2005 11:19 Uhr Seite 30


FPN 10 - 3000 - 1 H

04


18

16

14

12

10

8

6

4

2

3000



FPN 10 - 3000 - 1 H and

FPH 40 - 250 - 3


HP-pump.


28

FPN 10 - 3000 - 1 H







suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:

Single stage centrifugal fire pump, clockwise or anticlockwise rotation, with 1 size DN 125 suction inlet, 3 size

B delivery outlets, 1 connection for rapid intervention line, 1 connection for tank fill line, 1 connection for tank suction line (lockable by means of a butterfly valve)

Priming system:







Weight: 90 kg


2 size A suction inlets, another delivery outlet, connection for another rapid intervention line, monitor connection, fitting of a pump proportioner






.................................................

168987



.................................................

169106



.................................................

156546



.................................................

156548

Kap.04-29 29.03.2005 11:19 Uhr Seite 29


FPN 10 - 3000 - 2 H

FPN 10 - 3000 - 2 H









DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:

Dual stage centrifugal fire pump, clockwise or anticlockwise rotation, with 1 size DN 125 suction inlet,

3 size B delivery outlets, 1 connection for rapid intervention line, 1 connection for tank fill line, 1 connection for tank suction line (lockable by means of a butterfly valve)

Priming system:







Weight: 115 kg


2 size A suction inlets, another delivery outlet, connection for another rapid intervention line, monitor connection, fitting of a pump proportioner






.................................................

169290



.................................................

169724



.................................................

156549



.................................................

156550

18


8

6

12

10

16

14

4

2

3000



FPN 10 - 3000 - 2 H and

FPH 40 - 250 - 3


HP-pump.


29

04

Kap.04-30 29.03.2005 11:20 Uhr Seite 30


FPN 10 - 4000 - 2 H

04

18

16

14

12

10

8

6

4

2




FPN 10 - 4000 - 2 H and

FPH 40 - 250 - 3


HP-pump.


FPN 10 - 4000 - 2 H







suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:

Dual stage centrifugal fire pump, clockwise or anticlockwise rotation, with flange for suction inlet and flange for delivery outlet

Priming system:







Weight: 97 kg (basic pump)


2 size Storz A suction inlets, alternatively 1 size Storz 150 suction inlet, tank suction connection size

DN 150, up to 6 size B delivery outlets,

1 monitor outlet, 2 delivery outlets to rapid intervention units, 1 outlet for tank fill line, fitting of a pump proportioner


ANS, TOURMAT D, draining device,

TROKOMAT shut-off, MAD 50



.................................................

156454



.................................................

156455



.................................................

156456



.................................................

156457

30

Kap.04-31 29.03.2005 11:21 Uhr Seite 27


FPN 10 - 6000 - 2 H

FPN 10 - 6000 - 2 H







suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:


Priming system:









2 size Storz 125 suction inlets, alternatively 1 size DN 200 suction inlet,

2 size DN 150 tank suction connections, up to 8 size B delivery outlets or

2 size A delivery outlets (lockable by means of an intermediate valve),

2 monitor outlets, 2 delivery outlets to rapid intervention units, 1 outlet for tank fill line, fitting of a pump proportioner



TROKOMAT shut-off, EAD



.................................................

156466



.................................................

156467



.................................................

156468


(rotation, please see page2)

.................................................

156469

14

12

10

8

6

4

2

18


16

0 1000 2000 3000 4000 5000 6000 7000 8000 9000 points of guarantee: geod. suction height 3 m, geod. suction height 7.5 m


FPN 10 - 6000 - 2 H and

FPH 40 - 250 - 3


HP-pump.


31

04

Kap.04-32 29.03.2005 11:21 Uhr Seite 30

04

Picture with

HP-pump

CENTRIFUGAL FIRE PUMPS

FPN 10 - 8000 - 1 H

AND FPN 10 - 8000 - 1 HH

8

6

4

2

12

10

16

14

18


0

1500 3000 4500 6000

8000

7500 9000 10500 12000 13500


ANS, TOURMAT D, AWZ system, draining device, foam agent proportioning system



.................................................

199413



.................................................

199414



.................................................

199415



.................................................

199416

FPN 10 - 8000 - 1 H and

FPN 10 - 8000 - 1 HH

ZIEGLER centrifugal fire pump

(rear-mounted) for vehicle PTO or aggregate of 270 kW (H),

320 kW (HH) onwards

Pump output in separate operation:

Normal pressure pump (H):


suction height

High pressure pump (HH):

250 l/min at 40 bar


10,000 l/min at 8 bar and 1.5 m geod.

suction height

Drive:

Via joint shafts from the PTO of the vehicle or pump aggregate

Basic fittings:

Single stage centrifugal fire pump with flange for suction inlet and flange for delivery outlet. The high pressure pump is attached, with a high pressure outlet to the rapid intervention unit.

Priming system:



Normal pressure pump: 1 manometer and 1 mano-vacuummeter,

1 running hour meter

High pressure pump: 1 high pressure manometer, switch and control lamp


Dim. (LxWxH):

FPN 10 - 8000 - 1 H:

730x760x770 mm

FPN 10 - 8000 - 1 HH:

780x760x850 mm

Weight:

FPN 10 - 8000 - 1 H:

200 kg (basic pump)

FPN 10 - 8000 - 1 HH:

258 kg with HP-pump


1 size DN 205 central suction inlet (to water tank) or 3 size F suction inlets

DN 50, connected by means of a collecting head. Up to 8 size B or 2 size A delivery outlets (lockable by means of an intermediate valve). Up to

2 delivery outlets to rapid intervention units. 1 outlet for tank fill line. Up to 2 monitor outlets. Outlet for another high pressure rapid intervention line for the high pressure pump.

32

Kap.04-33 29.03.2005 11:22 Uhr Seite 27


FPN 15 - 1000 - 2 H

FPN 15 - 1000 - 2 H







suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:


Priming system:







Weight: 76 kg


2 more delivery outlets, connection for a second rapid intervention line, monitor connection, fitting of a pump proportioner






.................................................

169352



.................................................

169485



.................................................

156542



.................................................

156544

20


8

6

4

2

18

15

16

14

12

10



FPN 15 - 1000 - 2 H and

FPH 40 - 250 - 3


HP-pump.


33

04

Kap.04-34 29.03.2005 11:22 Uhr Seite 30


FPN 15 - 2000 - 1 H

04

All FPN can be retrofitted with

HP-pump.


34

20


18

15

16

14

12

10

8

6

4

2

2000



FPN 15 - 2000 - 1 H and

FPH 40 - 250 - 3

FPN 15 - 2000 - 1 H







suction height


(test floor performance complying with DIN EN 1028)



suction height

Drive:


Basic fittings:


Priming system:







Weight: 90 kg


2 more delivery outlets, connection for a second rapid intervention line, connection for monitor, fitting of a pump proportioner






.................................................

168987



.................................................

169106



.................................................

156546



.................................................

156548

Kap.04-35 29.03.2005 11:23 Uhr Seite 27


FPN 15 - 2000 - 2 H

FPN 15 - 2000 - 2 H







suction height



DIN EN 1028)


suction height


suction height

Drive:


Basic fittings:


Priming system:







Weight: 115 kg


2 more delivery outlets, connection for a second rapid intervention line, connection for monitor, fitting of a pump proportioner






.................................................

169290



.................................................

169724



.................................................

156549



.................................................

156550

20


18

15

16

14

12

10

8

6

4

2

0 300 600 900 1200 1500

2000

1800 2100 2400 2700 3000 points of guarantee: geod. suction height 3 m geod. suction height 7.5 m


FPN 15 - 2000 - 2 H and

FPH 40 - 250 - 3


HP-pump.


35

04

Kap.04-36 29.03.2005 11:57 Uhr Seite 30


FPN 15 - 3000 - 1 H

04

20


10

8

6

4

18

15

16

14

12

2

3000



FPN 15 - 3000 - 1 H and

FPH 40 - 250 - 3


HP-pump.


36

FPN 15 - 3000 - 1 H







suction height




suction height


suction height

Drive:


Basic fittings:

Single stage centrifugal fire pump, clockwise or anticlockwise rotation, with size DN 125 suction inlet, 3 size B delivery outlets, 1 connection for rapid intervention line, 1 connection for tank fill line, 1 connection for tank suction line (lockable by means of a butterfly valve)

Priming system:







Weight: 90 kg


Another delivery outlet, connection for a second rapid intervention line, connection for monitor, fitting of a pump proportioner






.................................................

168987



.................................................

169106



.................................................

156546



.................................................

156548

Kap.04-37 29.03.2005 11:59 Uhr Seite 27


FPN 15 - 3000 - 2 H

FPN 15 - 3000 - 2 H







suction height




suction height


suction height

Drive:


Basic fittings:


Priming system:









2 size Storz A suction inlets, alternatively 1 size Storz 150 suction inlet, tank suction connection DN 150, up to

6 size B delivery outlets, 1 monitor outlet, 2 outlets to rapid intervention units, 1 outlet for tank fill line, fitting of a pump proportioner



TROKOMAT shut-off, MAD 50



.................................................

156454



.................................................

156455



.................................................

156456



.................................................

156457

20


15

16

14

12

10

8

6

4

2



FPN 15 - 3000 - 2 H and

FPH 40 - 250 - 3


HP-pump.


37

04

Kap.04-38 29.03.2005 12:50 Uhr Seite 30

04


FPH 40 - 250 - 3

60

50

40

30

20

10


0 100 200

250

300 400 500 600 700 points of guarantee: 125 l/min 48 bar 250 l/min 40 bar


Example:

FPN 10 - 750 - 2 H and

FPH 40 - 250 - 3

FPH 40 - 250 - 3



Attachable pump for all normal pressure pumps

Power required: 50 - 90 kW

The required high pressure power must be added to the figures of the respective normal pressure pump!


250 l/min at 40 bar



590 l/min at 40 bar

Drive:

The pump is put into circuit via gear drive and electromagnetic clutch.

Basic fittings:

3-stage centrifugal fire pump, clockwise or anticlockwise rotation, with 2 normal pressure inlets, left or right, with feed line.

1 high pressure outlet with distributor and 1 or 2 hand-operated high pressure outlets, drain valve, thermal discharge line.


High pressure indicator or possibly button ”high pressure ON/OFF” on the modular operation and control panel




Weight: 58 kg


Another high pressure outlet, all high pressure outlets remote controlled, electronic pressure limitation, audible overheating warning device, electronic overheating protection with automatic water exchange


HP-pump.

38

Kap.04-39 29.03.2005 12:50 Uhr Seite 27

PUMP UNIT

FP 16/8-2 A

12

10

8

6

4

2

16


14

7,5 m geod.

suction height

6 m geod.

suction height

1,5 m and 3 m geod. suction height

0 200 400 point of guarantee:

600 800 1000 1200 1400 1600 1800 2 000

3 m geod. suction height

FP 16/8-2 A

ZIEGLER fire pump unit

FP 16/8-2 A on mounting frame



suction height

Engine:

VW industrial Diesel engine type

H 200 ADG, 4-cyl. in-line engine, water-cooled, 41 kW (55 HP); with electric starter, battery 12 V/66 Ah, generator 12 V/65 A, fuel tank 48 l

Basic fittings:

Pump

Dual stage centrifugal fire pump

FP 16/8-2, with 1 size A suction inlet,

2 size B delivery outlets with selfclosing globe valves complying with

DIN-standard, suction inlet and delivery outlets with blank caps

Priming system:


Pump gauges:

1 manometer and 1 mano-vacuummeter mounted on the pump

Controls:

All instruments and switches necessary for the operation of the engine are found in a control box at the front side of the unit.

Illumination:

1 telescopic halogen spotlight, illuminated control panel

Colour:

Frame: black

Cover and pump: red (RAL 3000)


Weight: 312 kg

.................................................

123410

04

39

Kap.04-40 29.03.2005 12:51 Uhr Seite 30

PUMP UNIT

FP 24/8-1 A

16


14

12

10

8

6

4

2

7,5 m geod.

suction height

3 m geod.

suction height

1,5 m geod.

suction height

0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 point of guarantee: 3 m geod. suction height

04

FP 24/8-1 A


FP 24/8-1 A on mounting frame or for mounting on a truck or on chassis trailer

Pump output:




suction height

Engine:

Mercedes-Benz Diesel engine

(EURO 2) type OM 904 LA, 4-cyl. in-line engine, turbocharger and boost intercooling, water-cooled, 100 kW

(136 HP), with electric starter. Power transmission to the pump by means of electromagnetic clutch and joint shaft,

2 batteries 12 V/66 Ah, fuel tank 60 l.

Basic fittings:

Pump

Single stage centrifugal fire pump

FP 24/8-1, with 1 size A suction inlet,


DIN-standard, suction inlet and delivery outlets with blank caps

Priming system:

TROKOMAT PLUS fully automatic

Gauges:

1 manometer and 1 mano-vacuummeter installed together with the engine controls on the control panel

Colour:

Basic framerame: black

Cover: red (RAL 3000)

Pump: silver (RAL 9006)


Weight: 1050 kg


2 additional delivery outlets, fitting of a pump proportioner, spotlight

.................................................

196850

Single axle platform trailer for FP 24/8-1 A and fire fighting accessories. With rubber-cushioned axle, overrunning brake, towbar adjustable in height and supporting wheel, with 2 positioning supports, illumination complying with StVZO

(German road regulations).

Colour:

Frame, wheels and towbar: black

Mudguards: white

Dim. (LxWxH): 4200x1955x1100 mm

Weight: 400 kg

G.V.W.: 1600 kg

...................................................

17248

40

Kap.04-41 29.03.2005 12:52 Uhr Seite 27

PUMP UNIT

FP 48/8-2 A

18

16

14

12

10

8

6

4

2


7,5 m geod.

suction height

3 m geod.

suction height

1,5 m geod.

suction height

0 600 1200 1800 2400 3000 3600 point of guarantee: 3 m geod. suction height

4200 4800 5400 6000

FP 48/8-2 A


FP 48/8-2 A on mounting frame or for mounting on a track or on chassis trailer

Pump output:


Engine:


(EURO 2) type OM 904 LA, 4-cyl. in-line engine, turbo-charger and boost intercooling, water-cooled,

125 kW (170 HP), with electric starter.

Power transmission to the pump by means of electromagnetic clutch and joint shaft, fuel tank 65 l.

Basic fittings:

Pump


FP 48/8-2, with 2 size A suction inlets,


DIN-standard, suction inlets and delivery outlets with blank caps

Priming system:


Gauges:


Colour:

Basic frame: black




Weight: 1120 kg


Fitting of a pump proportioner, spotlight

.................................................

196849



Colour:


Mudguards: white

Dim. (LxWxH): 4500x2000x1100 mm

Weight: 450 kg

G.V.W.: 2500 kg

...................................................

17249

04

41

Kap.04-42 29.03.2005 12:52 Uhr Seite 30

PUMP UNIT

FP 60/10-2 A

04

8

6

4

2

14

12

10

18


16

7,5 m geod.

suction height

3 m geod.

suction height

1,5 m geod.

suction height

0 1000 2000 3000 4000 5000 point of guarantee: 3 m geod.suction height

6000 7000 8000 9000

FP 60/10-2 A


FP 60/10-2 A on mounting frame or for mounting on a truck or on chassis trailer

Pump output:


suction height

Engine:


(EURO 2) type OM 906 LA, 6-cyl. in-line engine, turbo-charger and boost intercooling, water-cooled,

205 kW (278 HP), with electric starter.

Power transmission to the pump by means of electromagnetic clutch and joint shaft, fuel tank 120 l.

Basic fittings:

Pump


FP 60/10-2, with 2 size Storz 125 suction inlets, 6 size B delivery outlets with self-closing globe valves complying with DIN-standard.

Alternatively 2 size A delivery outlets with shut-off valve and 2 size B delivery outlets. Suction inlets and delivery outlets with blank caps.

Priming system:


Gauges:


Colour:

Basic frame: black



Dim. (LxWxH): 3100x1100x1800 mm

Weight: 1950 kg


Fitting of a pump proportioner, spotlight

.................................................

196851



Colour:


Mudguards: white

Dim. (LxWxH): 4600x2200x1200 mm

Weight: 600 kg

G.V.W.: 3500 kg

...................................................

34095

42

Kap.04-43 29.03.2005 12:53 Uhr Seite 27

PORTABLE PUMP

TS 8/8 ULTRA-POWER

8

6

4

2

16


14

12

10

7,5 m geod.

suction height

0 400 point of guarantee:

800 1200

3 m geod. suction height

3 m geod.

suction height

1,5 m geod.

suction height

1600 2000

7,5 m geod. suction height

2200

TS 8/8 Ultra-Power

PVR 380/4/97

The TS 8 portable pump complying with DIN-standard with the highest output

»The environment-friendly one«

• High performance: 1800 l/min at

8 bar and 3 m geod. suction height

• Reliable VW Polo 4-stroke aluminium engine (worldwide VW service facilities)

• Low pollution, low vibration and low noise

• Performance as draining pump

2000 l/min at 3 m geod. suction height

Nominal output:


Pump output (approx.): at 3 m geod. suction height:

1950 l/min at 6 bar

1800 l/min at 8 bar

1500 l/min at 10 bar at 1.5 m geod. suction height:


1050 l/min at 8 bar

Pump:

Single stage centrifugal fire pump, high efficiency - approx. 70%. Watercarrying parts made of sea-water resistant light metal alloy or stainless steel. Sealing of pump shaft by means of radial seals. With size A suction inlet and 2 size B delivery outlets with selfclosing globe valves, all with couplings and blank caps. Power transmission from engine via single-plate dry clutch.

Priming system:


Engine:

VW Polo 4-cyl. 4-stroke aluminium engine with electronic fuel injection and lambda control, type ATE.

Power: 37 kW (50 HP) at 5000 rpm,

999 cc.

Cooling through closed cooling water circuit with heat exchanger and additional cooling system (patented).

Electronic 2-stage rpm-limiter for suction and max. rpm acting on the injection unit. Contactless battery ignition, maintenance-free hydraulic valve lift system.

Starter: Electric starter. Emergency start by means of pull starter.

Engine cowling of plastic.

Fuel tank: 16 l for unleaded premium petrol (RON 95) sufficient for 2 hours at nominal performance.


Functional and clear arrangement of all gauges and controls on the pump.

Manometer, mano-vacuummeter, running hour meter as well as all engine controls: Ignition switch, rotary knob for ”throttle” (easy operation without choke), control lamps for oil pressure, water temperature, battery charge and suction rpmlimitation.

Clutch lever between pump and engine cowling.

Lighting system:

1 halogen spotlight, extensible

Carrying frame:

High-strength light metal frame with

4 foldable handles adjustable to 90º with cold-protective covering of rubber


Weight: 189 kg (ready for use)

ZIEGLER portable pump TS 8/8 single stage, with automatic priming system TROKOMAT PLUS

.................................................

208669

ZIEGLER portable pump TS 8/8 single stage, with automatic priming system TROKOMAT PLUS and automatic pressure governor

Tourmat D

.................................................

218100

Tourmat D

The automatic pressure governor

Tourmat D takes some of the load off the operator during action. In case of change in water delivery, e.g. when nozzles are opened and closed, the pressure is adjusted within fractions of a second and is kept constant. This is particularly advantageous if several pumps are connected in series.

43

04

Kap.04-44 29.03.2005 12:53 Uhr Seite 30

PORTABLE PUMP

TS 8/8 ULTRA-LIGHT

04

16


14

12

10

8

6

4

2

7,5 m geod. suction height

3 m geod.

suction height

1,5 m geod.

suction height

0 200 400 600 800 1000 1200 1400 1600 1800 2000 point of guarantee: 3 m geod. suction height 7,5 m geod. suction height

2200

TS 8/8 Ultra-Light

PVR 357/7/92

The TS 8 portable pump complying with DIN-standard with the lowest weight

The pump that sets standards

• Low weight: 140 kg

• High performance: 1600 l/min at

8 bar and 3 m geod. suction height

• Easy-to-start ZIEGLER/Hirth

2-cyl. engine, 36 kW (49 HP), aircooled, with auto-lube system

• Performance as draining pump:

2000 l/min at 3 m geod. suction height

Nominal output:



1900 l/min at 6 bar

1600 l/min at 8 bar



950 l/min at 8 bar

Pump:

Single stage centrifugal fire pump, high efficiency - approx. 70%. Watercarrying parts made of sea-water resistant light metal alloy or stainless steel. Sealing of pump shaft by means of radial seals.

With size A suction inlet and 2 size B delivery outlets with self-closing globe valves, all with couplings and blank caps. Power transmission from engine via single-plate dry clutch.

Priming system:


Engine:

ZIEGLER/Hirth 2-cyl. engine, aircooled, diaphragm controlled, with auto-lube system, 625 cc, power

36 kW (49 HP) at 4900 rpm. Noise suppressing design of engine cowling. With 24 l fuel tank for unleaded/leaded premium petrol, lubricant tank and pull starter.

Rpm/load controlled auto-lube with low level oil warning lamp and automatic shut-off when no oil is left.

Option: Electric starter and 12 V battery with charging socket.

Engine cowling of plastic.


Modern operating panel with 1 manometer and 1 mano-vacuummeter, running hour meter, rotary knobs for

”throttle” and ”air”, control lamps ”oil” and ”cooling” and shut-off. Start button for version with electric starter.

Clutch lever between pump and engine cowling.

Lighting system:

1 halogen spotlight, extensible, illuminated operating panel

Carrying frame:


4 foldable handles adjustable to 90º with cold-protective covering


Weights (ready for use):

140 kg (without electric starter)

152 kg (with electric starter)

ZIEGLER portable pump TS 8/8 single stage, with automatic priming system TROKOMAT PLUS

.................................................

119283

ZIEGLER portable pump TS 8/8 single stage, with automatic priming system TROKOMAT PLUS, with additional electric starter and battery

.................................................

119308

44

Kap.04-45 29.03.2005 12:54 Uhr Seite 27

PORTABLE PUMP

TS 6/6 ULTRA-COMPACT

6

5

4

3

2

1

10

9

8

7


7,5 m geod.

height

0 100 200 300 400 500 600 700 point of guarantee: 3 m geod. suction height

800 900 1000 1100

TS 6/6 Ultra-Compact

The compact one of the ZIEGLER

”ULTRA”-line models

»The small strong one«

• Dual stage ZIEGLER centrifugal fire pump with time-tried components

• Reliable, low noise Briggs &

Stratton 4-stroke engine

(worldwide service facilities)

• Standard automatic priming system

• Storage space identical with

5 kVA generator, DIN 14685

Nominal output:



800 l/min at 4 bar

650 l/min at 6 bar



380 l/min at 6 bar

Pump:

Dual stage centrifugal fire pump.

Water-carrying parts made of seawater resistant light metal alloy or stainless steel. Impellers with stainless steel split water rings. Sealing of pump shaft by means of radial seals. With size B suction inlet with blank cap and

1 size B delivery outlet with selfclosing globe valve. Power transmission from engine via automatic centrifugal clutch.

Priming system:


Engine:

Briggs & Stratton 2-cyl., 4-stroke

V-engine, 570 cc, power 13 kW (18 HP) at 3600 rpm, with 8.5 l fuel tank for unleaded or leaded petrol (not below

85 RON), air-cooled by means of blower. Maintenance-free, electronic, contactless magneto ignition. Starting system with recoil starter and with electric starter and battery.


1 manometer and 1 mano-vacuummeter on the pump. Modern operating panel with rotary knob for ”throttle”, shut-off button, ignition switch, running hour meter, oil pressure warning lamp and halogen spotlight.

Carrying frame:


4 foldable handles with cold-protective covering


Weight (ready for use): 94 kg

ZIEGLER portable pump TS 6/6 dual stage, with automatic priming system TROKOMAT PLUS, with electric starter and battery

.................................................

182294

04

45

Kap.04-46 29.03.2005 12:55 Uhr Seite 30

PORTABLE PUMP

TS 2/5 ULTRA-PICCO

04

TS 2/5 Ultra-Picco

The smallest one of the ZIEGLER

”ULTRA”-line models





suction height

Pump:

Single stage centrifugal fire pump with impeller open on one side, designed for dirty water. Water-carrying parts made of sea-water resistant light metal alloy. Shaft made of stainless steel.

Pump shaft sealing by means of radial seals. With 1 size C52 suction inlet,

1 size C52 delivery outlet with selfclosing globe valve, both with coupling and blank cap. Direct power transmission engine-pump.

Engine:

Göbler-Hirth 1-cyl., 2-stroke engine type H165, air-cooled, 164 cc, power

4.6 kW (6.3 HP) at 4500 rpm. With recoil-starter and 3.6 l tank for mixture

1:50.

Priming system:

Piston pump, manual


1 mano-vacuummeter with protective cap on the pump housing, throttle

Carrying frame: Of steel pipe


Weight (ready for use): 34.5 kg

ZIEGLER portable pump TS 2/5

H165 single stage, with piston pump priming system

.................................................

182310

Protective hood of lattice plastic *

...................................................

20053

8


7

6

5

4

3

2

1

6 m geod.

suction height

3 m geod.

suction height

1,5 m geod.

suction height

0 50 100 150 200 250 300 point of guarantee: 3 m geod. suction height

350 400 450 500 550

46

Kap.04-47 29.03.2005 12:55 Uhr Seite 27

PORTABLE PUMPS

WITH DIESEL ENGINE

TS 6/6-2 AND TS 800 D

TS 6/6-2

14

12

10

8

6

4

2

16 delivery rate Q (l/min)

7.5 m geod.

suction height

3 m geod.

suction height

1.5 m geod.

suction height


TS 6/6-2 with Diesel engine

Pump output:





suction height

Pump:

Dual stage ZIEGLER centrifugal fire pump, water-carrying parts made of sea-water resistant light metal alloy, shaft made of stainless steel. Sealing of the pump shaft by means of radial seals. With size B suction inlet and size

B delivery outlet with self-closing globe valve, size B couplings.

Engine:

Ruggerini 2-cyl., 4-stroke Diesel engine, type MD 191, direct injection, air-cooled, power 12 kW (16.3 HP) at

3600 rpm, 851 cc. With electric starter as well as emergency roller starter.

4 l fuel tank.

Priming system:



1 manometer and 1 mano-vacuummeter, operating panel with throttle and ON/OFF button

Carrying frame:

Carrying/protective frame of steel pipe with 4 foldable handles.


Weight: 114 kg (ready for use)

ZIEGLER portable pump TS 6/6 dual stage, with automatic priming system TROKOMAT PLUS

.................................................

223361

TS 800 D

16 delivery rate Q (l/min)

14

12

10

8

6

4

2

0 200 400 600

1,5 m geod.

height suction height

800 1000 suction height

1200 1400 1600 1800 2000

TS 800 D with Diesel engine

Pump output:



Pump:

Dual stage ZIEGLER centrifugal fire pump, water-carrying parts made of sea-water resistant light metal alloy, shaft of stainless steel. Sealing of the pump shaft by means of radial seals.

With size A suction inlet and 2 size B delivery outlets with self-closing globe valves. Size B couplings and blank caps. Power transmission from engine by means of centrifugal clutch.

Engine:

Ruggerini 2-cyl., 4-stroke Diesel engine, type RD 270, direct injection, air-cooled, continuous power 20 kW

(27 HP) at 3600 rpm, 1204 cc. With electric starter and 10 l fuel tank.

Priming system:



1 manometer and 1 mano-vacuummeter on the pump. Operating panel with throttle and ON/OFF button.

Carrying frame:

Carrying/protective frame of steel pipe with 4 foldable handles


Weight: 170 kg (ready for use but without battery)

ZIEGLER portable pump TS 800 D dual stage, with automatic priming system TROKOMAT PLUS

.................................................

122281

47

04

Kap.04-48 20.02.2006 12:36 Uhr Seite 1

ZIEGLER portable pumps with the automatic priming system

TROKOMAT PLUS high performance, reliable, well-proven for decades in tough actions.

ZIEGLER builds portable pumps with various performances: from 200 up to 2000 l/min, e.g. from the small light-weight TS 2/5 Ultra-

Picco up to the high-performance

TS 8/8 Ultra-Power. With powerful

2-stroke or 4-stroke engines or as a

Diesel aggregate.

One thing they all have in common:

The time-tried construction with extremely efficient priming systems and rugged, reliable engines make our portable pumps sought-after and reliable partners to the ﬁre brigades in many countries of the world.

More than 70,000 ZIEGLER portable pumps are in use worldwide.

Albert Ziegler GmbH & Co. KG • Manufacturers of ﬁre service vehicles, pumps and hoses

Memminger Str. 28 • 89537 Giengen • Germany

Phone +49 7322 951-0 • Fax +49 7322 951-464

WWW: http://www.ziegler.de • E-Mail: export@ziegler.de