Printed in Japan
2006/2(CL.K)
284-8050-01
4. Mounting Procedure
CCD Camera Power Supply Box
CAA-188-210
Installation Instructions
4-1. Mounting the CCD Camera Power Supply Box
Mount the CCD camera power supply box in a location such as under a seat using either
the supplied tapping screws (ø4 x 12) or velcro.
1. Precautions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician
for help.
■ Mounting Using Tapping Screws
■ Mounting Using Velcro
CCD camera
power supply box
ø4✕12
CCD camera
power supply box
ø4✕12
INFORMATION FOR USERS:.
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL
VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.
Velcro
* Thoroughly wipe any dirt from the mounting
surface.
* Remove the separator from the back of the
velcro and apply it to the mounting surface.
2. Package Contents
Fig.3
1. CCD camera power supply box: ············· 1 4. Bag of accessories: ················· 1 bag
Clamp: ······················································ 1
Tapping screws: ········································ 4
2. Selector switch: ························ 1 bag
AUTO/MANU selector switch: ··················· 1
Mounting fitting: ········································ 1 5. Bag of accessories: ················· 1 bag
Label: ························································ 1
Connector cable (red): ······························ 1
Connector cable (light green): ·················· 1
3. Bag of accessories: ················· 1 bag
Connector cable (black): ··························· 1
Electro taps: ·············································· 2
Connector cable (red): ······························ 1
Velcro: ······················································· 1
Velcro: ······················································· 1
Fig.4
4-2. Mounting the AUTO/MANU Selector Switch
■ Mounting the Switch on the Dashboard
Mount the switch on the dashboard as shown in Fig. 6 using the supplied switch mounting
hole (Fig. 5).
Cosmetic cover (vehicle part)
Prepared ø12 hole
Label
Cosmetic cover (vehicle part)
3. Making Connections
3-1. System Connection Example
AUTO/MANU selector
switch cable
AUTO/MANU selector switch
<1DIN TV, 2DIN TV>
Mounting nut
CAUTION
Upper
White
Selector switch knob
Yellow
CCD camera
power supply box
Prepared ø12 hole
CCD camera
Mount so that notch on AUTO/MANU
selector switch faces downward.
Fig.5
Fig.6
Light green
Black
Red
GND
To reverse gear
signal (12 V)
■ Mounting the Switch Below the Dashboard
Assemble the AUTO/MANU selector switch as shown in Fig. 7 and mount it below the
dashboard. (See Fig. 8.)
To ACC power supply (12 V)
Mounting fitting
For making connections to a TV
or video monitor equipped
with a video input jack
Fig.1
3-2. Connecting the Supplied Cables
Label
Harness
Nut
Hook up the supplied connector cables as shown in Fig. 2.
Mounting fitting
Label
AUTO/MANU selector
switch
MA
NU
Nut
MA
NU
AU
TO
AU
TO
Black
Clamp
Harness
AUTO/MANU selector
switch
Light
green
Clamp
Red
* Secure the switch harness to portion A of the
mounting fitting using the clip.
Fig.7
To reverse gear signal (12 V)
Tapping screws (ø4 x 12)
Fig.8
GND
CAUTION
To ACC power supply (12 V)
FIG.2
Used to provide a 12 V power supply
to an additional device.
2. Before drilling any holes in a vehicle, make sure that there are no electrical wires, brake fluid
pipes, or the like, running behind to surface to be drilled.
3-3. Power Cable Connections
When connection cannot be made to the terminals, use the supplied Electro Tap to make
the connection as illustrated in the diagram.
As illustrated in the diagram, the intermediate
cable is brought against the stopper and bent
back in the direction of the arrow.
The tip of the cable is
cut at a convenient
length.
From the vehicle side
Pass the vehicle-side cable through and
bend back in the direction of the arrow.
Hook
Power cable
Explanation of label indications
: The CCD camera image is given output
priority.
From the unit
Stopper
Power cable
3. When installation is complete, test the AUTO/MANU selector switch to make sure it works
properly.
• MANU (manual)
Not needed
Latch
Coupler connected
to another piece of
equipment
From the unit
1. If harnesses will come into contact with the sharp edges of metal plates, or the like, protect
them using grommets or insulation tubes.
• AUTO (automatic) : Normally, the TV image is output. The
camera image is output when the
transmission is shifted into reverse.
Vehicle-side wire
Close with pliers until the latch engages.
Clarion Co., Ltd.
Unit-side cable
Vehicle-side cable
284-8050-01
Page 1
06.2.22, 3:33 PM
Adobe PageMaker 7.0J/PPC