COPAL ELECTRONICS PRESSURE TRANSDUCERS WITH AMP. PA-110 INTERNAL STRUCTURE 5 1 A Port 2 B Port 3 4 Part name ■FEATURES 1 Sensor chip ● Heavy-duty casing for ourdoor use ● Supply voltage : 5 VDC or 12 VDC ● Built-in temperature compensation 2 Pressure Port 3 Housing 4 “O” ring 5 Resin compound Material Silicone PPS (Polyphenylene sulphide) Nitrile rubber Silicone gel ■MODEL NUMBER DESIGNATION PA-110-102D-012 Supply voltage Series name 012:12 VDC 005: 5 VDC Rated pressure range 102: 0 ~ 100 kPa Pressure refence D:Differntial ■LIST OF MODEL NUMBERS Differential Pressure reference Rated pressure range kPa Supply voltage VDC Model number 0 ~ 100 12 5 PA-110-102D-012 PA-110-102D-005 ※Verify the above model numbers when placing orders. ■ Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. COPAL ELECTRONICS PA-110 PRESSURE TRANSDUCERS WITH AMP. ■STANDARD SPECIFICATIONS K Unless otherwise specified, the specs are defined at an ambient temperature of 25±5 °C and excitation voltage of 5 V DC or 12 VDC. Item PA-110 Model number 102D-012 102D-005 General specifications Pressure reference Differential Rated pressure range kPa 100 Maximum pressure kPa 200 Break-down pressure kPa 500 Operating temp. range °C − 20 ~ 70 %RH Operating humidity °C Storage temp. 35 ~ 85(No condensation) − 20 ~ 80(Atmospheric pressure, humidity 65 %RH maximum) Pressure medium Non-corrosive gases g Power Net weight Analog output Approx. 70 12 ± 0.25 V 5 ± 0.1 V Supply voltage V DC Ripple content maximum 10 %(P-P) Consumption current maximum 10 mA Output voltage Zero voltage ※1 Span voltage ※1 Output current V 0.5 ~ 4.5 V 0.5 ± 0.04 V 4.0 ± 0.04 mA maximum 0.5(Load resistance 10 kΩ minimum) Linearity/Hysteresis %F.S. ± 0.5 Thermal error -20 ~ 70 °C (Reference temp.: 25 °C) %F.S. ±3 Response ※1 φ 4.5 mm Pressure port ms 2 The zero and span voltages of 5 V vary in proportion to the supply voltage. ■ Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request. COPAL ELECTRONICS PA-110 PRESSURE TRANSDUCERS WITH AMP. ■ENVIRONMENTAL CHARACTERISTICS Test item Test conditions (At 25 ± 5 °C) Vibration 10 ~ 500 Hz, 1.5 mm maximum/294 m/s , 3 directions for 2 hours each Shock 490 m/s2, 3 directions for 3 times each Pressure cycling 0 ~ Rated pressure, 10 cycles Moisture resistance 40 °C, 90 ~ 95 %RH, 240 hrs. Permissible change 2 Zero voltage/Span voltage: ± 1 %F.S. maximum 6 ■OUTLINE DIMENSIONS ᰑ Output 30 φ 4.5 1 ° ᰒ Common ᰓ Power (+) φ 5.5 ± 0.1 Unless otherwise specified, tolerance : ± 0.5 (Unit: mm) A port 4 17 B port port [ Pressure Tolerance : 0.2 (mm) ] Output connectors Applied plug AMP econoseal J series Mark (+) Made in Tyco Electronics AMP K.K. Plug Housing 174357-2 Double Lock Plate 174358-1 Contact Seal Ring Label 1 (Polyester) (55) Laser marking Part No. Housing 1 (PPS) 19 37 Pin No. 1 2 3 36 50 Housing 2 (PPS) 8.5 Metal color insert (Brass) Connection Output Common Power B 13.5 2 – φ 5.5 11.5 16 64 33 ■INTERNAL ELECTRICAL SCHEMATICS – 012 (12 VDC) – 005 (5 VDC) PressureA Power B PressureA Sensor PressureB Main circuit Common C Output PressureB Power B Sensor Main circuit Common C Output ■ Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.