ITEM NO.: LS-19996
ASSEMBLY INSTRUCTIONS:
WARNING: MAKE SURE POWER SUPPLY IS TURNED OFF AT MAIN BREAKER.
※VERY IMPORTANT
PLEASE READ THOROUGHLY. CAREFULLY UNPACK THIS LAMP AND PLACE ON A SOFT SURFACE.
*WE STRONGLY RECOMMEND A QUALIFIED ELECTRICIAN TO ASSEMBLE THE FIXTURE.
*IT IS A 2 OR MORE PERSONS JOB.
*NEVER LIFT THE FIXTURE BY ARMS OR GLASS POLE, LIFT BY CHAIN LOOP OR CHAIN.
*OPEN THE OUTER BOX AND TAKE OUT OF THE INNER PACKAGE FROM THE OUTER BOX CAREFULLY AND
PLACE THE INNER PACKAGE ON A FLAT SURFACE, MAKE SURE THE THICKEST STYROFOAM IS FACING
UPWARDS.
*REMOVE THE THICKEST STYROFOAM CAREFULLY BY LIFTING THE THICKEST STYROFOAM VERTICALLY.
*REMOVE THE UPPER WHITE GLASS SHADES AND CLEAR GLASS SHADES FROM MIDDLE STYROFOAM.
*REMOVE THE MIDDLE STYROFOAM FROM BOTTOM STYROFOAM BY LIFTING THE MIDDLE STYROFOAM
VERTICALLY.
*REMOVE THE LOWER WHITE GLASS SHADE AND LOWER CLEAR GLASS SHADE FROM BOTTOM STYROFOAM
*REMOVER THE PLASTIC BAGS FROM ARMS, PUT BACK THE ARMS INTO THE DIE CUT OF BOTTOM
STYROFOAM.
1. Screw the Pole (Y) to the top of the Distributor (I).
2. Lift the fixture by chain loop and Distributor carefully, then place the Distributor support at the bottom of the
distributor (I) to support the fixture.
WARNING: DO NOT LIFT THE FIXTURE BY ARM OR GLASS POLE, LIFT BY CHAIN LOOP, CHAIN OR
DISTRIBUTOR
3. Insert the Nipple (F) of the Arm (E) into the holes in Distributor (I), then adjust the Arm (E) to get proper position
and secure with the Screws (H) by using the Allen key (G) as shown.
4. Determine the length of chain required to hang the fixture at the desire height, remove the chain as desired
5. Attach the Crossbar (R) to the Outlet box (P) using two Screws (S).
6. Make wire connections: Attach ground wire from fixture to the Outlet box (P) ground wire using a Wire connector
(Q) (or attach them to the Crossbar (R) with a green ground screw), Attach the neutral (or white) wire from fixture
to neutral wire from power source with a Wire connector (Q), Attach the live (or black) wire from fixture to live
wire from power source with a Wire connector (Q)
7. Spread the electrical splices so that the Live wire is on one side of the outlet box and the Neutral wire is on the
other side.
8. Slide the Screw collar nut (X), Large plastic grommet (W), Glass canopy (V), Three rubber washers (U) and then
metal canopy (T) over the end of the chain, next, secure the Screw collar loop onto the nipple in the Crossbar (R).
9. Attach the Upper clear glass shade (C) to each Upper sockets (D), then screw Upper white glass shade (B) to the
upper sockets (D) as shown.
10. Install SIX Type B bulb 60W maximum (included) into each Upper sockets (D).
11. Install ONE Type C bulb 15W maximum (included) into the Lower socket (Z).
12. Line up the holes in the Lower white glass shade (L) with the holes in the Distributor (I), then secure with three
plastic grommets (J) and three Screws (K), be careful not to over tighten.
13. Line up the holes in the Lower clear glass shade (O) with the Screws (K), then secure with three Plastic grommets
(M) and three Reeded screws (N), be careful not to over tighten.
14. Restore power, Bulb already installed and enjoy your new lamp.
Use 6pcs, B -Type E12 120V 60W (Maximum) bulb
& C -Type E12 120V 15W (Maximum) bulb (All bulbs included)
* Please inform your dealer immediately in case of any parts shortage.
* Save these instructions for future reference.