Draft Not To Be
2.A.2 Lime production
Quoted
1
2
3
Category
Title
NFR:
2.A.2
Lime production
SNAP:
040614
Lime
ISIC:
2694
Manufacture of cement, lime and plaster
Version
Guidebook 2013
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Coordinator
Jeroen Kuenen
Contributing authors (including to earlier versions of this chapter)
Jozef M. Pacyna, Otto Rentz, Dagmar Oertel, Carlo Trozzi, Tinus Pulles and Wilfred
Appelman
23
Draft Not To Be Quoted
1
Draft Not To Be
2.A.2 Lime production
Quoted
24
25
Contents
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
1
2
3
4
5
6
7
Overview ................................................................................................................................... 3
Description of sources ............................................................................................................... 3
2.1
Process description ........................................................................................................... 3
2.2
Techniques ....................................................................................................................... 4
2.3
Emissions ......................................................................................................................... 4
2.4
Controls ............................................................................................................................ 5
Methods..................................................................................................................................... 6
3.1
Choice of method ............................................................................................................. 6
3.2
Tier 1 default approach..................................................................................................... 7
3.3
Tier 2 technology-specific approach ................................................................................ 9
3.4
Tier 3 emission modelling and use of facility data ......................................................... 12
Data quality ............................................................................................................................. 15
4.1
Completeness ................................................................................................................. 15
4.2
Avoiding double counting with other sectors ................................................................. 15
4.3
Verification..................................................................................................................... 16
4.4
Developing a consistent time series and recalculation ................................................... 16
4.5
Uncertainty assessment .................................................................................................. 16
4.6
Inventory quality assurance/quality control (QA/QC) ................................................... 16
4.7
Gridding ......................................................................................................................... 16
4.8
Reporting and documentation ........................................................................................ 17
Glossary .................................................................................................................................. 17
References ............................................................................................................................... 17
Point of enquiry....................................................................................................................... 18
50
Draft Not To Be Quoted
2
Draft Not To Be
2.A.2 Lime production
Quoted
51
1
Overview
52
53
54
55
56
Lime (CaO) is the high-temperature product of the calcination of limestone. The production
occurs in vertical and rotary kilns fired by coal, oil or natural gas. Calcium limestone contains 97–
98 % calcium carbonate on a dry basis. The rest includes magnesium carbonate, aluminium oxide,
iron oxide and silica. However, some limestone contains as much as 35–45 % magnesium
carbonate and is classified as dolomite.
57
58
59
60
61
Atmospheric emissions in the lime manufacturing industry include particulate emissions from the
mining, handling, crushing, screening and calcining of the limestone and emissions of air
pollutants generated during fuel combustion in kilns. These emissions are not very significant on a
global or even regional scale. However, lime works can be an important emission source of air
pollutants on a local scale.
62
63
64
The production of lime causes emissions from both processes and combustion. This chapter only
covers the process emissions. Emissions from combustion activities are addressed in chapter
1.A.2.f Manufacturing Industries and Construction (Combustion) — Other.
65
2
Description of sources
66
2.1
Process description
67
68
69
70
71
72
73
Two major types of processes can be considered within the lime work operations: quarrying,
crushing, and size grading of minerals; and combustion of fuels in lime kilns. Limestone quarries
are usually developed in a number of benches or lifts. For primary blasting of the limestone, holes
are made by drills operated by compressed air (Parker, 1978). The excavated limestone is
transferred for crushing and grinding. There are several types of crushing and grinding machines
to produce limestone of sizes suitable for several designs of kilns. A schematic overview of the
different processes occurring during the production of lime is shown in Figure 2.1.
74
75
76
77
During the kiln operations the limestone reaches temperatures as high as 900 °C, and carbon
dioxide is driven off limestone to leave so-called quicklime. The quicklime descends through the
cooling zone and is discharged at the base of the kiln. Obviously, various air pollutants are
generated during combustion of fuels in the kiln.
78
79
80
Hydrated lime is made by adding water to crushed or ground quicklime and thoroughly mixing the
quicklime and the water. Milk of lime can be produced either by slaking quicklime with an excess
of water or by mixing hydrated lime with water.
Draft Not To Be Quoted
3
Draft Not To Be
2.A.2 Lime production
Quoted
Chapter 1.A.2.f
Chapter 1.B.1.b
Crushing,
Size grading
Quarrying
Quarry
Excavated
Limestone
Pretreatment
Combusting
Limestone
Kiln
Lime
Cooling,
Shipping
Posttreatment
Fuel
81
82
Figure 2.1
83
2.2
84
85
86
87
88
At present two major types of kilns are in use: vertical and rotary kilns. Because of larger size of
charge material, lower air velocities and less agitation, vertical kilns emit lower amounts of
particles but higher amounts of sulphur dioxide and carbon monoxide. However, in recent years
there have been important developments in the design and use of rotary kilns. They require a more
carefully classified and smaller size of limestone than for the vertical kilns.
89
2.3
90
91
92
93
94
95
Pollutants released are sulphur oxides (SOx), nitrogen oxides (NOx), volatile organic compounds
(non-methane VOC and methane (CH4)), carbon monoxide (CO), carbon dioxide (CO2), nitrous
oxide (N2O) and particulate matter. According to CORINAIR90 the main relevant pollutants are
SO2, NOx, CO and CO2 (Bouscaren, 1992). Fuel-based emissions are included under source
category 1.A.2 Manufacturing Industries and Construction (Combustion) and not included here to
prevent double counting.
96
97
98
99
100
101
102
103
104
Sulphur dioxide emissions are influenced by several factors, including the sulphur content of the
fuel, the sulphur content and mineralogical form (metal sulphide such as pyrite, or sulphates such
as gypsum) of the stone feed, the quality of lime being produced and the type of kiln. Due to
variations in these factors, plant-specific SO2 emission factors are likely to vary significantly from
the average emission factors presented here. The dominant source of sulphur emissions is the
kiln’s fuel, particularly coal and petroleum derived coke, where the levels of sulphur may be as
high as 5 % by weight. The amount of sulphur present will vary widely according to the nature of
the deposits used. During the calcining operation, sulphide and sulphates are decomposed to yield
sulphur dioxide. On combustion of the fuel, the sulphur compounds present in the fuel are
Process scheme for source category 2.A.2 Lime production.
Techniques
Emissions
Draft Not To Be Quoted
4
Draft Not To Be
2.A.2 Lime production
Quoted
105
106
oxidised to sulphur dioxide and pass through the burning zone of the kiln with the exhaust gases
(US EPA, 1995; HSMO, 1992).
107
108
109
110
111
112
When sulphur-containing fuels are burnt, for practical purposes sulphur in the kiln exhaust may be
assumed to be emitted as sulphur dioxide, although there is usually some sulphur trioxide formed.
In the case of lime manufacture in shaft kilns, much of the sulphur re-combines with the burnt
lime and the emissions of sulphur dioxide are subsequently reduced. In the case of rotary and
rotating hearth kilns, combinations of process design and combustion conditions can be selected to
ensure that most of the sulphur is expelled as sulphur dioxide in the kiln gases (HSMO, 1992).
113
114
115
116
117
118
119
The oxides of nitrogen are produced through the reaction of the nitrogen and oxygen in the air and
through the oxidation of the nitrogen compounds contained in the fuel. There is a significant
increase in the amount of oxides of nitrogen (mainly nitric oxide) which is formed at temperatures
above 1 400 °C. The formation of nitric oxide is also a function of the excess air. When operating
near to stoichiometric conditions in the kiln, there is localised generation of carbon monoxide.
This acts as a reducing agent so that any nitric oxide which may be present is converted to
nitrogen. Some oxides of nitrogen are also formed in electrostatic precipitators (HSMO, 1992).
120
121
122
Carbon dioxide and carbon monoxide are formed as main products of the combustion process.
Carbon monoxide is formed by the incomplete combustion of carbonaceous fuels and even with
good combustion control small amounts of carbon monoxide will be present in combustion gases.
123
124
125
126
127
The dissociation of limestone produces up to 0.75 tonnes of carbon dioxide (CO2) per tonne of
quicklime, depending on the composition of the limestone and the degree of calcination. The
amount of carbon dioxide produced by combustion depends on the chemical composition of the
fuel and on the heat use per tonne of quicklime, generally it is in the range 0.2–0.45 tonnes CO2
per tonne of quicklime (European Commission, 2001).
128
129
130
131
132
133
The heat of dissociation of calcium limestone is 3 200 MJ/tonne. The net heat use per tonne of
quicklime varies considerably with kiln design. Rotary kilns generally require more heat than shaft
kilns. The heat use tends to increase as the degree of burning increases. The net heat use varies
between 3 600 and 7 500 MJ/Mg of lime for calcium quicklime and light- and hard-burned
dolomite, and between 6 500 and 10 500 MJ/Mg of lime for dead-burned dolomite (European
Commission, 2001).
134
2.4
135
136
137
138
Emissions of sulphur oxide can be reduced by using low sulphur fuels and by limiting the sulphur
contents of the fuel and raw materials. Sulphur dioxide emissions may be further reduced if the
polluting equipment is fitted to desulphurise the exhaust gases (e.g. by using a wet process) (US
EPA, 1995; HMSO, 1992).
139
140
141
142
143
The design of kiln and combustion conditions may be selected to ensure that most of the sulphur is
retained in the burnt lime. In most circumstances, especially in shaft kilns, only a small fraction of
the sulphur dioxide generated within the kiln (whether originating from the raw materials or from
the fuel) is released to atmosphere, since it is mainly incorporated into the lime by chemical
combination (HSMO, 1992).
144
145
The following techniques can be reasonably applied to reduce oxides of nitrogen discharges to the
atmosphere:
Controls
Draft Not To Be Quoted
5
Draft Not To Be
2.A.2 Lime production
Quoted
146

the use of low-NOx-burners where practicable, which operate by avoiding localised hot spots;
147
148

the use of very finely pulverised coal so that complete combustion can be achieved with low
excess air.
149
150
151
Modern lime works are equipped with electrostatic precipitators that remove at least 98 % of the
particulate matter from exhaust gases. Other control devices are also used including multiple
cyclones, wet scrubbers and baghouses.
152
3
Methods
153
3.1
Choice of method
154
155
Figure 3.1 presents the procedure to select the methods for estimating process emissions from the
lime industry. The basic approach is as follows:
156

If detailed information is available such that higher tiered methods can be employed: use it.
157
158
159
160

If the source category is a key category, a Tier 2 or better method must be applied and
detailed input data must be collected. The decision tree directs the user in such cases to the
Tier 2 method, since it is expected that it is easier to obtain the necessary input data for this
approach than to collect facility level data needed for a Tier 3 estimate.
161
162
163

The alternative of applying a Tier 3 method, using detailed process modelling is not explicitly
included in this decision tree. However, detailed modelling will always be done at the facility
level and results of such modelling could be seen as ‘facility data’ in the decision tree.
Draft Not To Be Quoted
6
Draft Not To Be
2.A.2 Lime production
Quoted
Start
Facility data
Available?
Yes
All production
covered
No
Yes
Use Tier 3
Facility data
only
No
Use Tier 3
Facility data &
extrapolation
Technology
Stratification
available?
Use Tier 2
technology specific
activity data
and EFs
Yes
No
Key source?
Get
technology stratified
activity data
and EFs
Yes
No
Apply Tier 1
default EFs
164
165
Figure 3.1
166
3.2
167
3.2.1 Algorithm
168
The Tier 1 approach for process emissions from lime uses the general equation:
Tier 1 default approach
E pollutant  AR production  EFpollutant
169
170
Decision tree for source category 2.A.2 Lime production.
(1)
where:
171
Epollutant
=
the emission of the specified pollutant
172
ARproduction
=
the activity rate for the lime production
173
EFpollutant
=
the emission factor for this pollutant
174
175
176
177
This equation is applied at the national level, using annual national total lime production data.
Information on the production of lime, suitable for estimating emissions using the simpler
estimation methodology (Tier 1 and 2), is widely available from United Nations statistical
yearbooks or national statistics.
178
179
180
The Tier 1 emission factors assume an ‘averaged’ or typical technology and abatement
implementation in the country and integrate all different sub-processes in the lime production
between inputting raw materials into the process and the final shipment off the facilities.
Draft Not To Be Quoted
7
Draft Not To Be
2.A.2 Lime production
Quoted
181
182
In cases where specific abatement options are to be taken into account a Tier 1 method is not
applicable and a Tier 2 or Tier 3 approach must be used.
183
3.2.2 Default emission factors
184
185
186
187
188
189
The Tier 1 approach needs emission factors for all relevant pollutants that integrate all subprocesses within the industry from inputting raw materials to the final shipment of the products off
site. The default emission factor for total suspended particulates (TSP) as given in Table 3.1 has
been extracted from the Best Available Techniques Reference (BREF) document for cement and
lime production (European Commission, 2001) and represents worst case TSP emissions (i.e.
uncontrolled process) during lime production (kiln, hydrating and grinding).
190
191
192
193
PM10 and PM2.5 emission factors have been estimated using the particulates profile suggested in
the Coordinated European Particulate Matter Emission Inventory Program (CEPMEIP)
(Visschedijk et al., 2004). The BC1 emission factor is based on Chow et al. (2011) and related to
PM2.5.
194
195
196
Emission factors in the BREF documents are mostly given in ranges. The range is interpreted as
the 95 % confidence interval, while the geometric mean of this range is chosen as the value for the
emission factor in the table below.
197
Table 3.1
Tier 1 emission factors for source category 2.A.2 Lime production.
NFR source category
Fuel
Not applicable
Not estimated
Pollutant
TSP
PM10
PM2.5
BC
Tier 1 default emission factors
Code
Name
2.A.2
Lime production
NA
NH3, As, Cr, Cu, Ni, Se, Zn, HCH, PCB, PCDD/F, Benzo(a)pyrene, Benzo(a)fluoranthene,
Benzo(k)fluoranthene, Indeno(1,2,3-cd)pyrene, HCB
NOx, CO, NMVOC, SOx, Pb, Cd, Hg
Value
Unit
Reference
95 % confidence interval
Lower
Upper
9 000 g/Mg lime
3 000
22 000
European Commission (2001)
3 500
700
0.46
g/Mg lime
g/Mg lime
% of PM2.5
1 000
300
0.23
9 000
2 000
0.92
Visschedijk et. (2004) applied on TSP
Visschedijk et. (2004) applied on TSP
Chow et al. (2011)
198
199
200
201
202
203
Emission factors in Table 3.1 are provided for particulate fractions only. This does not imply that
there are no process emissions for other pollutants but since it is very difficult to separate process
and combustion emissions and we expect the majority of emissions for other pollutants (NOx, SOx,
NMVOC, CO, cadmium (Cd), mercury (Hg) and lead (Pb)) to be due to the combustion of fuels.
Emission factors for combustion-related emissions of NOx, CO and SO2 are provided in chapter
1.A.2.f. Emissions of other heavy metals are assumed to be negligible.
204
3.2.3 Activity data
205
206
207
208
Information on the production of lime, suitable for estimating emissions using the simpler
estimation methodology (Tiers 1 and 2), is widely available from United Nations statistical
yearbooks or national statistics. National statistics are preferred if they are judged to be complete
and representative of the sector.
1
For the purposes of this guidance, BC emission factors are assumed to equal those for elemental carbon (EC). For
further information please refer to Chapter 1.A.1 Energy Industries.
Draft Not To Be Quoted
8
Draft Not To Be
2.A.2 Lime production
Quoted
209
210
211
Further guidance is provided in the 2006 IPCC Guidelines for National Greenhouse Gas
Inventories, volume 3 on Industrial Processes and Product Use (IPPU), chapter 2.3.1.3 ‘Choice of
activity data’ (IPCC, 2006).
212
3.3
Tier 2 technology-specific approach
213
3.3.1
Algorithm
214
215
216
217
The Tier 2 approach is similar to the Tier 1 approach. To apply the Tier 2 approach, both the
activity data and the emission factors need to be stratified according to the different techniques
that may occur in the country. With regard to the lime production, these techniques include the use
of the various kilns:
218

vertical shaft kiln;
219

vertical double inclined kiln;
220

parallel flow / counterflow regenerative kiln;
221

annular kiln;
222

rotary short kiln / air suspension preheater;
223

rotary long kiln;
224

calcimatic kiln.
225
Draft Not To Be Quoted
9
Draft Not To Be
2.A.2 Lime production
Quoted
226
The Tier 2 approach is as follows:
227
228
Stratify the lime production in the country to model the different product and process types
occurring in the national industry into the inventory by:
229
230

defining the production using each of the separate product and/or process types (together
called ‘technologies’ in the formulae below) separately; and
231

applying technology specific emission factors for each process type:
E pollutant 
232
 AR
production,technology
 EFtechnology,pollutant
(2)
technologies
233
where:
234
235
ARproduction,technology
=
the production rate within the source category, using this
specific technology
236
EFtechnology,pollutant
=
the emission factor for this technology and this pollutant
237
238
A country where only one technology is implemented will result in a penetration factor of 100 %
and the algorithm reduces to:
E pollutant  AR production  EFtechnology,pollutant (3)
239
240
where:
241
Epollutant
=
the emission of the specified pollutant
242
ARproduction
=
the activity rate for the lime production
243
EFpollutant
=
the emission factor for this pollutant
244
The emission factors in this approach will still include all sub-processes within the industry.
245
3.3.2 Technology-specific emission factors
246
247
248
249
250
The present subsection presents uncontrolled and controlled emission factors, which are taken
from the BREF document for cement and lime production (European Commission, 2001). The BC
emission factor is based on Chow et al. (2011) and related to PM2.5. Emission factors are based on
a typical exhaust gas volume of 4 000 Nm3/Mg lime for the calcining process. The gaseous
effluent from hydrating plants is rather small in volume, estimated is 800 m3/Mg of hydrated lime.
251
252
253
254
255
During lime grinding, air is drawn through all of the grinding equipment to remove ground lime of
the required particle size. The product is separated from air in bag filters, often preceded by
clones. Thus, dust collection is an integral part of the process and therefore uncontrolled emission
factors are not applicable to the process of lime grinding. The typical air flow during grinding is
1 500 Nm3/Mg lime.
256
257
258
The majority of the particulate emissions arise from the calcining of limestone. Other processes
like hydrating and grinding are less important for the PM emissions. In the tables in this chapter,
these emissions have been added up to get emission factors for the whole process.
259
260
Subsidiary operations, such as crushing, screening, conveying, slaking, storage and discharge are
not included in the tables below. Emission factors for these processes are not available.
Draft Not To Be Quoted
10
Draft Not To Be
2.A.2 Lime production
Quoted
261
262
263
Emission factors in the BREF documents are mostly given in ranges. The range is interpreted as
the 95 % confidence interval, while the geometric mean of this range is chosen as the value for the
emission factor in the table below.
264
3.3.2.1 Uncontrolled emission factors
265
Table 3.2
Tier 2 emission factors for source category 2.A.2 Lime production.
NFR source category
Fuel
SNAP (if applicable)
Technologies/Practices
Region or regional conditions
Abatement technologies
Not applicable
Not estimated
Pollutant
TSP
PM10
PM2.5
BC
Tier 2 default emission factors
Code
Name
2.A.2
Lime production
NA
040614 Lime (decarbonizing)
Typical emissions from some types of lime kiln
Uncontrolled
NH3, As, Cr, Cu, Ni, Se, Zn, HCH, PCB, PCDD/F, Benzo(a)pyrene, Benzo(a)fluoranthene,
Benzo(k)fluoranthene, Indeno(1,2,3-cd)pyrene, HCB
NOx, CO, NMVOC, SOx, Pb, Cd, Hg
Value
Unit
Reference
95 % confidence interval
Lower
Upper
9 000 g/Mg lime
3 000
22 000
European Commission (2001)
3 500 g/Mg lime
1 000
9 000
Visschedijk et al. (2004) applied on TSP
700 g/Mg lime
300
2 000
Visschedijk et al. (2004) applied on TSP
0.46 % of PM2.5
0.23
0.92
Chow et al. (2011)
266
3.3.2.2 Controlled emission factors
267
268
269
270
It is assumed that controlled rotary kilns are fitted with dust collection equipment, as are most
controlled shaft kilns. Because of the wide range of exhaust gas conditions, a variety of dust
collectors are used, including cyclones, wet scrubbers, fabric filters, electrostatic precipitators and
gravel bed filters.
271
272
Furthermore, it is assumed that both wet scrubbers and bag filters are used to de-dust the
emissions during lime hydrating.
273
Table 3.3
Tier 2 emission factors for source category 2.A.2 Lime production.
NFR source category
Fuel
SNAP (if applicable)
Technologies/Practices
Region or regional conditions
Abatement technologies
Not applicable
Not estimated
Pollutant
TSP
PM10
PM2.5
BC
Tier 2 default emission factors
Code
Name
2.A.2
Lime production
NA
040614 Lime (decarbonizing)
Typical emissions from some types of lime kiln
Controlled
NH3, As, Cr, Cu, Ni, Se, Zn, HCH, PCB, PCDD/F, Benzo(a)pyrene, Benzo(a)fluoranthene,
Benzo(k)fluoranthene, Indeno(1,2,3-cd)pyrene, HCB
NOx, CO, NMVOC, SOx, Pb, Cd, Hg
Value
Unit
95 % confidence interval
Reference
Lower
Upper
400 g/Mg lime
100
1 000
European Commission (2001)
200 g/Mg lime
60
400
Visschedijk et al. (2004) applied on TSP
30 g/Mg lime
10
80
Visschedijk et al. (2004) applied on TSP
0.46 % of PM2.5
0.23
0.92
Chow et al. (2011)
274
3.3.3 Abatement
275
276
Abatement efficiencies are not provided for lime production. Tier 2 uncontrolled and controlled
emission factors may be used.
Draft Not To Be Quoted
11
Draft Not To Be
2.A.2 Lime production
Quoted
277
3.3.4 Activity data
278
279
280
Information on the production of lime, suitable for estimating emissions using the simpler
estimation methodology (Tiers 1 and 2), is widely available, preferably from national statistics or
alternatively from United Nations statistical yearbooks.
281
282
283
Further guidance is provided in the 2006 IPCC Guidelines for National Greenhouse Gas
Inventories, volume 3 on Industrial Processes and Product Use (IPPU), chapter 2.3.1.3 ‘Choice of
activity data’ (IPCC, 2006).
284
3.4
285
3.4.1 Algorithm
286
287
There are two different methods to apply emission estimation methods that go beyond the
technology specific approach described above:
288

detailed modelling of the lime production process;
289

facility-level emission reports.
290
3.4.1.1 Detailed process modelling
291
292
A Tier 3 emission estimate, using process details will make separate estimates for the consecutive
steps in the lime production process:
293

handling of raw materials;
294

combustion in the kiln;
295

after-treatment of the lime.
296
297
298
This process modelling will need to be done using a tailored toolkit or a system with input from
experts in the industry. Where possible, process-specific emission factors will be needed to apply
to each of the activities.
299
3.4.1.2 Facility-level data
300
301
302
Where facility-level emissions data of sufficient quality (see the guidance chapter on data
collection in Part A of the Guidebook) are available, it is good practice to use these data. There are
two possibilities:
303

the facility reports cover all lime production in the country;
304

facility-level emission reports are not available for all lime plants in the country.
305
306
307
308
309
If facility-level data cover all lime production in the country, it is good practice to compare the
implied emission factors (reported emissions divided by the national lime production) with the
default emission factor values or technology specific emission factors. If the implied emission
factors are outside the 95 % confidence intervals for the values given below, it is good practice to
explain the reasons for this in the inventory report
310
311
312
If the total annual lime production in the country is not included in the total of the facility reports,
it is good practice to estimate the missing part of the national total emissions from the source
category, using extrapolation by applying:
Tier 3 emission modelling and use of facility data
Draft Not To Be Quoted
12
Draft Not To Be
2.A.2 Lime production
Quoted
E
Etotal, pollutant 
313
facility, pollutant
Facilities
314


  Productiontotal   Production facility   EFpollutant (4)
Facilities


where:
315
316
Etotal,pollutant
=
the total emission of a pollutant for all facilities within the
source category
317
Efacility,pollutant
=
the emission of the pollutant as reported by a facility
318
Productiontotal
=
the production rate in the source category
319
Productionfacility
=
the production rate in a facility
320
EFpollutant
=
the emission factor for the pollutant
321
322
323
Depending on the specific national circumstances and the coverage of the facility-level reports as
compared to the total national lime production, it is good practice to choose the emission factor
(EF) in this equation from the following possibilities, in decreasing order of preference:
324
325

technology-specific emission factors, based on knowledge of the types of technologies
implemented at the facilities where facility-level emission reports are not available;
326

the implied emission factor derived from the available emission reports:
EF 
327
E
Facility, pollutant
Facilities
 Production
(5)
Facility
Facilities
328
329

330
3.4.2 Tier 3 emission factors and models
331
332
333
334
335
336
337
Lime production facilities are major industrial facilities and emissions data for individual plants
might be available through a pollutant release and transfer registry (PRTR) or another emission
reporting scheme. When the quality of such data is assured by a well developed QA/QC system
and the emission reports have been verified by an independent auditing scheme, it is good practice
to use such data. If extrapolation is needed to cover all lime production in the country either the
implied emission factors for the facilities that did report, or the emission factors as provided above
could be used (see subsection 3.3.2 above).
338
339
340
A model setting out TSP emission factors for sub-processes within the lime industry
(Economopoulos, 1993) is presented in Table 3.4. It is a rather old model, which may be outdated,
and should therefore be used with care.
341
Table 3.4
the default Tier 1 emission factor. This option should only be chosen if the facility-level
emission reports cover more than 90 % of the total national production
Tier 3 emission factors for particulate emissions from lime production.
Operation
Coal storage
Abatement
(if applicable)
Emission factor
[kg/Mg lime]
Open piles
0.5
Semi-enclosed piles
0.25
Compartments
0.1
Draft Not To Be Quoted
13
Draft Not To Be
2.A.2 Lime production
Quoted
Silos
Coal crushing and
screening
Coal grinding
0.1
Uncontrolled
0.18
Fabric filter
0.002
(Semi) direct fired
system
Indirect fired system
0.0
Uncontrolled
10.0
Fabric filter
0.1
Raw material storage
0.16
Crushing and
screening
Crushed material
storage
1.5
Fabric filter
0.0005
Open piles
1.0
Semi-enclosed piles
0.5
Compartments
0.2
Silos
0.2
Raw material
conveying
Raw material
calcining
Uncontrolled
Vertical shaft kiln
Vertical double
Inclined kiln
Parallel flow /
Counterflow
Regenerative kiln
Annular kiln
Rotary short kiln / air
suspension preheater
Rotary long kiln
Uncontrolled
1.2
Fabric filter
0.01
Uncontrolled
3.0
Cyclone
1.0
Multicyclones
0.75
Uncontrolled
10.5
Cyclone
3.6
Multicyclones
2.6
Uncontrolled
8.0
Cyclone
2.8
Multicyclones
2.0
Uncontrolled
12.0
Cyclone
4.2
Multicyclones
3.0
Uncontrolled
40.0
Cyclone
14.0
Multicyclones
9.0
ESP
0.6
Fabric filter
0.2
Uncontrolled
140.0
Cyclone
49.0
Multicyclones
35.0
Draft Not To Be Quoted
14
Draft Not To Be
2.A.2 Lime production
Quoted
Calcimatic kiln
Lime cooling
Grate cooler
ESP
2.0
Fabric filter
0.4
Uncontrolled
25.0
Cyclone
8.7
Multicyclones
6.2
Uncontrolled
20.0
Cyclone
4.0
Multicyclones
2.0
Fabric filters
0.1
Planetary, rotary or
vertical shaft coolers
0.0
Lime packaging /
shipping
Lime hydration
0.12
Uncontrolled
35.0
Scrubber
0.04
342
343
344
More information on the typical emissions from a lime production facility may also be found in
the BREF document for the Cement and Lime industry (European Commission, 2001).
345
3.4.3 Activity data
346
347
348
Since PRTR generally do not report activity data, such data in relation to the reported facility level
emissions are sometimes difficult to find. A possible source of facility-level activity might be the
registries of emission trading systems.
349
350
351
352
The detailed methodology (Tier 3) requires more comprehensive information. For example, the
quantities of lime produced by various types of industrial technologies employed in the lime
industry at plant level. However, in most cases, no information is available from the statistical
yearbooks on the quantities of lime produced in vertical and rotary kilns.
353
4
Data quality
354
4.1
Completeness
355
356
In cases where attempts are made to split the emissions from lime manufacturing between
combustion emissions and non-emission combustions, care must be taken to include all emissions.
357
358
It is good practice to check whether the emissions reported as ‘included elsewhere’ (IE) under
source category 2.A.2 are indeed included in the emissions reported under source category 1.A.2.f.
359
4.2
360
361
In cases where it is possible to split these emissions, it is good practice to do so. However, care
must be taken that the emissions are not double counted.
Avoiding double counting with other sectors
Draft Not To Be Quoted
15
Draft Not To Be
2.A.2 Lime production
Quoted
362
363
It is good practice to check that the emissions reported under source category 2.A.2 are not
included in the emission reported under source category 1.A.2.f.
364
4.3
365
4.3.1 Best Available Technique (BAT) emission factors
366
367
368
369
370
This section presents Best Available Technique emission factors. These are provided by the BREF
document for this industry (European Commission, 2001), available at
http://eippcb.jrc.es/pages/FActivities.htm. The BREF document discusses the process, current
emission levels and provides Best Available Technique information but does not provide emission
values associated with the use of BAT.
371
4.4
372
373
374
For Tier 1 and Tier 2, activity data should be consistent across the time series. Where
technology-specific emission factors are introduced for Tier 2 these must be applied so that they
reflect the technology employed in the relevant years of the inventory calculation.
375
376
377
378
379
380
For Tier 3 using facility-level data, it might occur that a different selection of facility-level data is
included in different years. This can lead to time series inconsistencies. Moreover, PRTR data
generally are available for specific years only. Splicing such recent reported data under the
European Pollutant Emission Register (EPER) and the European Pollutant Release and Transfer
Register (E-PRTR) with historical data could be used to get consistent time series. Splicing could
be used for both the activity data and the country-specific emission factors.
381
382
383
Unexpected discontinuities in time series can occur when specific lime works come into operation
or are closed in specific years. If this happens, it is good practice to document such explanations
clearly in the inventory archives.
384
4.5
385
386
387
It is rather difficult to assess current uncertainties of emission estimates for pollutants emitted
during lime production. The uncertainties of sulphur dioxide emission estimates can be assessed in
a similar way as the uncertainties of estimates for fossil fuel combustion (see chapter 1.A.2.f).
388
4.6
389
390
391
392
393
As discussed in the present chapter, emissions from lime production only include the emissions
due to other causes than the combustion of fuels. Emissions from fuel combustion are to be
reported under source category 1.A.2.f in the Industrial Combustion sub-sector. It is good practice
to check whether the lime production data evaluated under the present chapter are consistent with
the associated fuel use reported under chapter 1.A.2.f.
394
4.7
395
396
397
It is good practice to consider lime production plants as point sources if plant-specific data are
available. Otherwise national emissions should be disaggregated on the basis of plant capacity,
employment or population statistics.
Verification
Developing a consistent time series and recalculation
Uncertainty assessment
Inventory quality assurance/quality control (QA/QC)
Gridding
Draft Not To Be Quoted
16
Draft Not To Be
2.A.2 Lime production
Quoted
398
4.8
Reporting and documentation
399
No specific issues.
400
5
Glossary
AR production, technology the production rate within the source category, using a specific technology
ARproduction
the activity rate for the lime production
E facility, pollutant
the emission of the pollutant as reported by a facility
E pollutant
the emission of the specified pollutant
E total, pollutant
the total emission of a pollutant for all facilities within the source category
EF country, pollutant
a country-specific emission factor
EF pollutant
the emission factor for the pollutant
EF technology, abated
the emission factor after implementation of the abatement
EF technology, pollutant
the emission factor for this technology and this pollutant
EF technology, unabated
the emission factor before implementation of the abatement
Penetration technology the fraction of production using a specific technology
Production facility
the production rate in a facility
Production total
the production rate in the source category
ηabatement
the abatement efficiency
401
402
6
References
Bouscaren, M.R., 1992. CORINAIR Inventory, Default Emission Factors Handbook. Second
edition. Commission of the European Communities, Paris.
Chow, J.C., Watson, J.G., Lowenthal, D.H., Chen, L.-W.A., and Motallebi, N., 2011. PM2.5
source profiles for black and organic carbon emission inventories. Atmospheric Environment 45
(2011) 5407-5414.
Economopoulos, A.P., 1993. Assessment of sources of air, water and land pollution. A guide to
rapid source inventory techniques and their use in formulating environmental control strategies.
Part one: rapid inventory techniques in environmental pollution. World Health Organization,
report WHO/PEP/GETNET/93.1-A, Geneva.
European Commission, 2001. Integrated Pollution Prevention and Control (IPPC), Reference
Document on Best Available Techniques (BREF) in the Cement and Lime Manufacturing
Industries, December 2001.
European Commission, 2010. Integrated Pollution Prevention and Control (IPPC), Reference
Document on Best Available Techniques (BREF) in the Cement and Lime Manufacturing
Industries. May 2010. Available at http://eippcb.jrc.es. (accessed 5 June 2013).
HSMO, 1992. Lime Manufacture and Associated Processes. Her Majesty’s Inspectorate of
Draft Not To Be Quoted
17
Draft Not To Be
2.A.2 Lime production
Quoted
Pollution, Environmental Protection Act 1990 Process Guidance Note IPR 3/1, London.
IPCC, 2006. 2006 IPCC Guidelines for National Greenhouse Gas Inventories. Eggleston H.S.,
Buendia L., Miwa K., Ngara T. and Tanabe K. (eds), National Greenhouse Gas Inventories
Programme. IGES, Japan.
Parker, A., 1978. ‘Iron and Steel works’. In: Industrial Air Pollution Handbook, Parker, A. (ed.).
Mc Graw-Hill, London.
US EPA, 1995. Compilation of Air Pollutant Emission Factors AP42 CD-ROM. United States
Environment Protection Agency, Research Triangle Park, North Carolina.
Visschedijk, A.J.H., Pacyna, J., Pulles, T., Zandveld, P. and Denier van der Gon, H., 2004.
‘Coordinated European Particulate Matter Emission Inventory Program (CEPMEIP)’. In: Dilara,
P. et al. (eds.), Proceedings of the PM emission inventories scientific workshop, Lago Maggiore,
Italy, 18 October 2004. EUR 21302 EN, JRC, pp. 163–174.
403
404
7
Point of enquiry
405
406
407
408
409
Enquiries concerning this chapter should be directed to the relevant leader(s) of the Task Force on
Emission Inventories and Projection’s expert panel on combustion and industry. Please refer to the
TFEIP website (www.tfeip-secretariat.org) for the contact details of the current expert panel
leaders.
Draft Not To Be Quoted
18