Wisconsin Department of Transportation
TRAFFIC INCIDENT MANAGEMENT
ENHANCEMENT (TIME)
TIME PROCUREMENT LIST BID DOCUMENT
August 30, 2010
Table of Contents
TRAFFIC CONTROL AND WORK ZONE PRODUCTS
1. ARROW BOARDS AND ARROW STICKS ...........................................................................................................2
2. TRUCK MOUNTED ATTENUATOR ......................................................................................................................4
3. TRUCK MOUNTED MESSAGE BOARDS ............................................................................................................5
4. BARRICADES AND LIGHTS.................................................................................................................................6
5. TRAFFIC CONES AND CONE LIGHTS ................................................................................................................9
6. DRUMS.................................................................................................................................................................10
7. DRUM WARNING LIGHTS ..................................................................................................................................13
8. CHANNELIZER CONES/POSTS .........................................................................................................................13
9. FLEXIBLE DELINEATOR POSTS ......................................................................................................................14
10. RED RETROREFLECTIVE FLAGS ...................................................................................................................16
11. ROAD FLARES ..................................................................................................................................................16
PERSONAL SAFETY PRODUCTS
12. FLASHLIGHTS AND FLASHLIGHT WAND .....................................................................................................18
13. LIGHTED TRAFFIC WANDS .............................................................................................................................19
14. BARRICADE TAPE ...........................................................................................................................................19
15. PANTS................................................................................................................................................................20
16. PERSONAL PROTECTION BEACONS ............................................................................................................21
17. VESTS (CLASS II) .............................................................................................................................................22
18. VESTS (CLASS III) ............................................................................................................................................23
19. RAIN JACKETS/PARKA ...................................................................................................................................23
20. WINDBREAKERS ..............................................................................................................................................24
21. WINTER (BOMBER) JACKETS ........................................................................................................................24
22. VEHICLE BEACON LIGHTS .............................................................................................................................25
TRAFFIC SIGNS
23. REFLECTIVE PRISMATIC SHEETING .............................................................................................................26
24. RIGID ROAD SIGNS ..........................................................................................................................................26
25. DETOUR SIGNS ................................................................................................................................................28
26. ROLLUP SIGNS AND STAND ..........................................................................................................................29
27. FOLD AND ROLL SIGN SYSTEMS ..................................................................................................................30
28. ROLL-UP SIGN SPRING STANDS ...................................................................................................................32
29. SLOW / STOP PADDLES ..................................................................................................................................32
OTHER
30. BATTERIES .......................................................................................................................................................34
31. VEHICLE CONSPICUITY TAPE ........................................................................................................................35
TIME Procurement List Bid Document
August 30, 2010
Page 1
TRAFFIC CONTROL AND WORK ZONE PRODUCTS
The following sections provide a description for the items we would like to offer through the
Procurement List.
Please note: You do not need to bid on every item. You are able to bid on only those items that
you distribute.
1. ARROW BOARDS AND ARROW STICKS
VEHICLE-MOUNTED ARROW BOARDS
Vehicle-mounted arrow boards have a heavy gauge aluminum alloy panel with flat black enamel finish.
Boards are available with 15 or 25 LED bulbs. The boards can run on a battery or 12 volt system and
the control console circuitry is housed in a compact cabinet which mounts in the cab of the vehicle for
easy operation. The applicable matching control panel, mounting brackets and assemblies for the bed
rail rack mounting option should be included in this bid price. Mounting options should be available for
manual tilt, power-tilt frame, bed floor rack, or tailgate mounting. Please note if there is a difference in
cost to alter the mounting method.
All boards must meet Federal Part VI of MUTCD requirements for arrow panels. Boards should be
visible for one mile and at a minimum of 18 degrees horizontal angle and 8 degrees vertical angle. The
bulbs should be sealed beam type lamps with yellow lenses or amber bulbs behind clear lenses and
should be equipped with an upper hood that surrounds not less than 180 degrees of the lamp.
The arrow functions are:
 Tri-function
 Sequential
 Flashing
The mode selections are:
 Both arrows simultaneously
 4-corner flashing
 Sequential chevron
 Caution
Type
Size
24” x 48”
Signs are available in the following sizes:
 24” x 48” (15 lights)
 30” x 60” (15 or 25 lights)
 36” x 72” (15 or 25 lights)
 48” x 96” (15 or 25 lights)
Vehicle-Mounted Arrow Boards
15 Bulbs
30” x 60” 36” x 72” 48” x 96” 30” x 60”
25 Bulbs
36” x 72”
Manufacturer Name /
Number
12V system - Cost
(Each) with Bed Rail
Mounting Kit
Manufacturer Name /
Number
Battery System Cost (Each) with Bed
Rail Mounting Kit
TIME Procurement List Bid Document
August 30, 2010
Page 2
48” x 96”
Type
Cost
(Each)
by Type
Mounting System (Board NOT Included)
Manufacturer
Mounting Systems
Name / Number
Tailgate Mount
Manual Tilt
Power Tilt
Bed Floor Rack
Bulk Head Rack
WORK AREA SOLAR ADVANCE WARNING BOARDS
Solar panels are all aluminum and are mounted to a heavy-duty, welded steel construction open deck
stable trailer. Amber lamps have an automatic intensity control to ensure maximum visibility. Signs
come equipped with 4-D deep-cycle batteries (L-16 battery). Signs must be equipped with an on-board
24-amp battery charger unless priced separately below. Standard models have 24 degree horizontal x
8 degree vertical angularity. Wide angle models have a 33 degree horizontal x 11 degree vertical
angularity. Signs can come with 15 or 25 lights and both models are 48” x 96”.
The arrow functions are:
 Right or Left arrow
 Both arrows simultaneously
 4-corner flashing
 Sequential arrows or chevrons
Work Area Solar Advance Warning Boards
Vertical Angularity
Cost
(Each)
by
Type
Standard
with Charger
Standard
without
Charger
Wide with
Charger
Wide without
Charger
24-Amp
Battery
Charger
Manufacturer
Name / Number
15 bulbs
Manufacturer
Name / Number
25 bulbs
ARROW STICKS
Traffic indicator bars/arrow sticks shall be available with either Halogen or LED lights and are encased
in heavy gauge aluminum with a non-reflective matte black finished panel. Bulbs shall be sealed beam
type lamps with yellow lenses or amber bulbs behind clear lenses; shall be equipped with an upper
hood that surrounds not less than 180 degrees of the lamp. The indicators are to be available in a solid
box or split box Flashing modes for the solid model are left or right arrow, double arrow and caution bar.
Flashing modes for split model are left or right arrow and double arrow caution. Solid arrow sticks shall
be a minimum of 54” in length and 13” in height; there shall also be a minimum of 10 lights. Split arrow
sticks shall be a minimum of 22” in length and 16” in height per side; a minimum of 5 lights shall be in
each side.
TIME Procurement List Bid Document
August 30, 2010
Page 3
Products shall be visible for a minimum of one-half mile. Shall also be visible at a minimum 18 degrees
horizontal angle and 8 degrees vertical angle, measured from a plane perpendicular to the arrow board
plane.
Arrow sticks shall be powered by a battery, solar array and components, or a circuit that connects to a
12V vehicle electrical system. Applicable control panel, mounting brackets and assemblies shall be
included. An optional magnetic mounting kit shall also be available.
Battery
Type
Full
Split
Arrow Sticks
Solar Array and
Components
Full
Split
12V Circuit
Full
Split
Manufacturer
Name / Number
Halogen
Cost
(Each)
by Type
Manufacturer
Name / Number
LED
Manufacturer
Name / Number
Magnetic
Mounting Kit
2. TRUCK MOUNTED ATTENUATOR
This specification is for a Truck Mounted Attenuator (TMA) that has been tested for minimum speeds of
60-mph. TMA’s are used for protecting county highway department personnel and equipment and the
general public from injury and damage caused when errant vehicles crash into highway department
equipment that is used in state highway maintenance operations.
TMA’s must meet NCHRP Report 350, test level 3 criteria; shall be able to withstand damage and
remain in service without repairs after incurring a collision on the rear of the TMA from a vehicle
traveling not more than 5 mph, weighing up to 4,400 pounds. TMA’s shall minimize, upon impact, the
acceleration and roll ahead distance of a stationary TMA support truck weighing no more than 22,000
lbs (actual weight).
After an impact, the TMA shall be completely self-contained (no exposed parts) and shall retain its
structure with no solid debris present from the system that can create a hazard on the roadway. The
TMA must be capable of tilting a minimum of 5 degrees from the horizontal. Refurbishment shall be
possible with hand tools. Welding to the truck must be done by, or under the direction of, a certified
welder. If self-installation is necessary, that must be noted.
The maximum width of the TMA shall be 7’9” and the maximum height from the ground shall be 45”.
The TMA shall be no more than 19’3” in length and shall weigh no more than 2,650 pounds.
Truck Mounted Attenuator
Manufacturer Name / Number
Truck Mounted Attenuator
Cost (Each)
TIME Procurement List Bid Document
August 30, 2010
Page 4
3. TRUCK MOUNTED MESSAGE BOARDS
Truck mounted message boards allow for a high degree of portability for incident management. Multiphase message boards are programmable to show text and arrows. Boards are designed to be
powered off of 12VDC vehicle electrical system. Boards shall be made of steel and aluminum or all
aluminum with a black finish. The board face shall be made of polycarbonate. All boards shall be wind
tested.
LEDs shall be amber in color and self contained and in a sealed LED unit. All LEDs shall be high
density, have adjustable brightness and have a viewing angle of 15 degrees. There shall be 4 LEDs per
pixel and LEDs shall work in temperatures from -40o to 140o F. The message display shall be full
matrix. Variable width and height fonts must be compliant with MUTCD guidelines.
A handheld controller, allowing operating from within the vehicle, shall be provided with each message
board. Owners shall be able to create, edit and display messages and the unit shall be able to store up
to 99 unique sequences.
Boards shall be visible from a minimum of one-half (1/2) mile; shall also be visible at a minimum of an
18 degree horizontal angle and 8 degree vertical angle, both measured from a plane perpendicular to
the arrow board plane. A flexible rail mounting system, developed to fit any vehicle type and size, shall
come with the message boards.
Sign Size
 30” x 74”
 31” x 75”
 38” x 50”
 42” x 75”
 44” x 70”
 48” x 96”
 55” x 90”
Cost (Each)
by Type with
Flexible Rail
Mounting
System
Cost
(Each)
by Type
Sign Mounting Options





Size
30” x 74”
31” x 75”
38” x 50”
42” x 75”
44” x 70”
48” x 96”
55” x 90”
Type
Tailgate Mount
Manual Tilt
Power Tilt
Bed Floor Rack
Bulk Head Rack
TIME Procurement List Bid Document
August 30, 2010
Tailgate
Manual Tilt
Power Tilt
Bed Floor Rack
Bulk Head Rack
Truck Mounted Message Boards
Manufacturer Name / Number
Message Boards
Mounting System (Board NOT Included)
Manufacturer Name / Number
Mounting Systems
Page 5
4. BARRICADES AND LIGHTS
BARRICADES
Reflective sheeting must be adhered to all barricades. Barricade reflective sheeting must be designed
specifically for use on rigid traffic control devices; conform to type H reflective sheeting, ASTM D4956
Type III or IV, class I or better; and have received a good or better rating in 1-year NTPEP tests for
shrinkage, cracking, blistering, colorfastness, reflectivity, adhesion and impact resistance. Barricades
must also conform to the crashworthiness criteria of NCHRP Report 350, test level 3. Certification, in
writing, may be required.
Barricades can be constructed of wood boards with angle iron legs, plastic boards with angle iron legs
or 100% low density polyethylene. Barricades must have a top rail that is punched to accept and
support a barricade light. . Stripe widths may be 4” (only for use when permitted by MUTCD) or 6”.
Sheeting must be high intensity grade (meets ASTM D4956 spec type II, class I), high intensity grade
prismatic (meets both ASTM D4956 Type III and Type IV specifications), diamond grade (exceeds
ASTM D4956 spec type IX standards), or diamond grade fluorescent.
Type I
 36” Height minimum
 Minimum rail length of 24”
 Width of rail: 8” minimum to
12” maximum
 2 relfectorized faces
Type
Type II:
 36” height minimum
 Minimum rail length of 24”
 Width of rail: 8” minimum to
12” maximum
 2 reflectorized faces
 Minimum 270 square inches
of reflective area
Type I
36 inch
Type III:
 48”, 60”, 72” ,96” or 120” long
panels
 Must be 96” if no sign attached
 Minimum 48” long if sign is
attached
 Panels must be at least 8” high
 Sheeting shall be provided on
both sides
Barricades - Wood with Angle Iron Legs
Type III (based on panel length)
Type II
36 inch
48 inch 60 inch 72 inch 96 inch 120 inch
Manufacturer Name /
Number
1-19
20-199
Cost (Each)
200-399
by Quantity
400-999
1000+
Type
Type I
36 inch
Barricades - Plastic with Angle Iron Legs
Type III (based on panel length)
Type II
36 inch
48 inch 60 inch 72 inch 96 inch 120 inch
Manufacturer Name /
Number
1-19
Cost
20-199
(Each)
200-399
by
Quantity 400-999
1000+
TIME Procurement List Bid Document
August 30, 2010
Page 6
Type I
36 inch
Type
Barricades - 100% Low Density Polyethylene
Type III (based on panel length)
Type II
36 inch
48 inch 60 inch 72 inch 96 inch 120 inch
Manufacturer Name /
Number
1-19
Cost
20-199
(Each)
200-399
by
Quantity 400-999
1000+
VERTICAL PANELS
Vertical Panel sheeting should be at least 8 inches wide and either 24, 29 or 36 inches tall. Sheeting
should be high intensity grade. Base should be included and made of rubber. Panels should fold flat, be
stackable and have an easy grip handle. If base is not included, please note the price for base and
panel individually. Base weight ought to be 20, 28, 30, or 43 pounds.
Vertical Panels - With Base
Type
20 lb
24” Tall
28 lb
30 lb
43 lb
20 lb
29” Tall
28 lb
30 lb
43 lb
Manufacturer Name / Number
1-19
20-199
Cost (Each)
200-399
By Quantity
400-999
1000 +
Type
20 lb
Vertical Panels – With Base
36” Tall
28 lb
30 lb
43 lb
Manufacturer Name / Number
1-19
20-199
Cost (Each)
200-399
By Quantity
400-999
1000 +
Type
20 lb
Vertical Panels - Without Base
24” Tall
29” Tall
28 lb
30 lb
43 lb
20 lb
28 lb
30 lb
Manufacturer Name / Number
1-19
20-199
Cost (Each) By
200-399
Quantity
400-999
1000 +
TIME Procurement List Bid Document
August 30, 2010
Page 7
43 lb
Vertical Panels – Without Base
36” Tall
20 lb
28 lb
30 lb
43 lb
Type
Manufacturer Name /
Number
1-19
20-199
Cost
200-399
(Each)
400-999
1000 +
Type
Manufacturer Name / Number
1-19
20-199
Cost (Each) 200-399
400-999
1000 +
20 Pound
Vertical Panel Bases
28 Pound
30 Pound
43 Pound
BARRICADE/DRUM LIGHTS
Lenses must be constructed of tough polycarbonate and the case must be made of high impact
resistant polycarbonate. Net weight is less than 2 pounds. Lights must have been tested in
temperatures ranging from -40oF to 175oF. Lights modes are flashing, steady burn or both with a threeway switch and are available in 6V or 12V with an optional photocell. Some lights are also available
with a LED circuit or may be solar powered. Lens color is amber with other options available as well.
Lights can also be used with most drums.
Type/Quantity
Barricade/Drum Lights
With Batteries
Without Batteries
Included
Included
6V
12V
6V
12V
LED Circuits
3V
6V
12V
Manufacturer Name /
Number
Each
20-199
Flasher
200-399
Cost
400-999
(Each)
1000 +
by
Type
Manufacturer Name /
and
Number
Quant
Each
20-199
Flasher w/
200-399
Photocell
400-999
1000 +
TIME Procurement List Bid Document
August 30, 2010
Page 8
Solar
Powered
Manufacturer Name /
Number
Each
20-199
Steadiburn
200-399
w/ Photocell
400-999
1000 +
Manufacturer Name /
Number
Each
20-199
Flasher/
Steadiburn
200-399
w/ Photocell 400-999
1000 +
5. TRAFFIC CONES AND CONE LIGHTS
TRAFFIC CONES
All traffic cones must meet the crashworthy requirements of NCHRP-350. All cones must include high
intensity grade reflective sheeting bands (which meet ASTM D4956 Spec Type III, Class 1) at 6” and 4”
from the top of the cone as specified by the MUTCD. Cones should be stackable. Cones shall have a
mounting hole at the top for a light and/or sign.

28” and 36” Cones - cones shall be made of low density polyethylene material and have a
weight of 7 or 10 pounds.

28” and 42” Grabber Style Cones with Handles - cones are made of a low density
polyethylene material. Have a handle or notch to grab onto at the top of the cone. The base
shall be removable and be available in weights of 10, 11, 15, 16 or 30 pounds.
Traffic Cones
28” Cones
Type
7 lb
36” Cones
10 lb
7 lb
10 lb
Manufacturer
Name / Number
Each/Set
Cost
20-199
(Each)
200-399
by
Quantity 400-999
1000 +
TIME Procurement List Bid Document
August 30, 2010
Page 9
Type
Grabber Style Traffic Cones with Handles
28” Cones
10 lb
11 lb
15 lb
16 lb
30 lb
Manufacturer Name /
Number
Each
20-199
Cost
(Each) by 200-399
Quantity
400-999
1000 +
Type
Grabber Style Traffic Cones with Handles
42” Cones
10 lb
11 lb
15 lb
16 lb
30 lb
Manufacturer Name /
Number
Each
20-199
Cost
(Each) by 200-399
Quantity 400-999
1000 +
TRAFFIC CONE LIGHTS
The cone lights, which shall have an amber, red, blue, green or white lens and will fit in the top of 18”,
28” and 36” cones with a minimum opening of 1-3/8”. Lens shall be a minimum of 6.25” long with a
head diameter no smaller than 3.75” and shall weigh no more than 0.75 pounds. Light source shall be
2-LED 4600 mcd, 20 mA. Lights may utilize 2-AA size batteries, 4-D size batteries, one D size battery,
solar powered NiMH battery, two 6V lantern batteries, or a 12V battery and battery will be included.
Battery compartment shall be screwed on. Lights must be visible from a minimum distance of 1,000
feet.
Quantity
Traffic Cone Light
Manufacturer Name
Traffic Cone Light
and Number
Each
Cost (Each) 20-199
by Quantity
200-399
400-999
1000 +
6. DRUMS
Drums are certified to meet the crashworthy requirements of NCHRP 350 and the MUTCD. Reflective
sheeting must conform to type H and have a good or better rating in 1-year NTPEP tests for shrinkage,
cracking, blistering, colorfastness, reflectivity, adhesion, flexibility and impact resistance. Drums should
be designed to inhibit roll after impact and have a rounded top to inhibit the buildup of any dangerous
TIME Procurement List Bid Document
August 30, 2010
Page 10
materials. Drum handle should have holes for mounting one or two lights with standard size bolt and
bolt protector. Drums shall be designed to inhibit roll after impact.
Drums are made of a high density polyethylene, are available with no base, with a tire ring, with a
plastic base (to use with sandbags), with a hollow plastic base (to be filled with sand) or with a 25,
30, 35 or 40 lb. rubber base, and drums are to be filled with sand bags.
Drums have either 4” or 6” high intensity retroreflective bands in the following grades:
 High Intensity Grade (Meets ASTM D4956 Spec Type III, Class 1)
 High Intensity Grade Prismatic (Meets both ASTM D4956 Spec Type III and IV specifications)
 Diamond Grade (Exceeds ASTM D4956 Spec Type IX standards)
 Diamond Grade Fluorescent
 Super High Intensity Grade
Quant.
Drums
Base
None
Bands
Tire
Ring
Plastic
Hollow
Plastic
Rubber
25 lb.
Rubber
30 lb.
Rubber
35 lb.
Rubber
40 lb.
200399
6”
4”
400999
20199
4”
4”
1000 +
High Intensity Grade
6”
4”
6”
6”
6”
6”
4”
200399
4”
400999
6”
4”
1000 +
20199
1-19
Manufacturer
Name / Number
4”
High Intensity Grade Prismatic
Cost (Each) by Quantity and Sheeting
1-19
Manufacturer
Name / Number
4”
4”
6”
6”
6”
TIME Procurement List Bid Document
August 30, 2010
Page 11
4”
200399
6”
4”
400999
20199
6”
4”
1000 +
Super High Intensity Grade
1-19
Manufacturer
Name / Number
4”
4”
6”
6”
6”
6”
4”
200399
6”
4”
400999
20199
4”
4”
1000 +
Diamond Grade
1-19
Manufacturer
Name / Number
4”
6”
6”
6”
20199
200399
400999
1000 +
Diamond Grade Fluorescent
1-19
Manufacturer
Name / Number
4”
6”
4”
6”
4”
6”
4”
6”
4”
6”
TIME Procurement List Bid Document
August 30, 2010
Page 12
7. DRUM WARNING LIGHTS
Drum lights must conform to NCHRP Report 350, test level 3.
Drum lights shall be available in Type A (flashing), Type C (steady burn) or Combination (flashing and
steady burn). The power source can be a LED source with 3V battery, 6V battery, 12V battery or four
D-type batteries. Lights should have a photocell.
Drum Warning Lights
Type
Power
Manufacturer Name /
Number
Each
Cost
(Each) by
Quantity
Type A
LED
6V
Type C
12V
4-D
LED
6V
12V
4-D
20-199
200-399
400-999
1000 +
Drum Warning Lights
Combination
Type
Power
Manufacturer Name /
Number
Each
Cost
(Each)
by
Quantity
LED
6V
12V
4-D
20-199
200-399
400-999
1000 +
8. CHANNELIZER CONES/POSTS
The cones/posts must satisfy all standards outlined in MUTCD and NCHRP Report 350 for
channelizing devices.
Cones/Posts are available at 28” high and 42” high, with 42” devices being the norm. A rubber base
shall be attached to the cone/post and shall be either 16 lb or 30 lb. There must be a handle at the top
that allows users to pick up the cone/post and allows for mounting of lights and signs. The reflective
sheeting must be on a 5 tier design and available in high intensity grade and diamond grade;
cones/posts should also be available with no reflective sheeting. Cones/posts must be telescoping.
TIME Procurement List Bid Document
August 30, 2010
Page 13
Cost
(Each)
by
Quantity
and Size
Sheeting
Rubber Base
Manufacturer Name /
Number
1-19
20-199
28”
200-499
500 +
Manufacturer Name /
Number
1-19
20-199
42”
200-499
500 +
Channelizer Cones/Posts
None
High Intensity Grade
Diamond Grade
16 lb.
30 lb.
16 lb.
30 lb.
16 lb.
30 lb.
9. FLEXIBLE DELINEATOR POSTS
Flexible delineator posts must meet the crashworthiness criteria of NCHRP report 350, test level 3.
They must be resistant to ultraviolet light, ozone, hydrocarbons, stiffening with age and a series of
direct wheel impacts with speeds varying up to 65 mph and rebounds to a vertical position if struck by a
standard vehicle. The weighted rubber base shall hold to the post securely using locking pins or other
devices and shall have high intensity reflective striping. The delineators must be tested for
temperatures ranging between -20oF and 160oF. Delineator posts shall be available in multiple heights
and multiple base weights as listed in the table below.
Base
Manufacturer Name / Number
1-9
10-24
18”
25-49
50-99
100+
Cost
(Each)
by
Quantity
and
Height
8 lb
10 lb
Flexible Delineator Posts
12 lb
15 lb
18 lb
Manufacturer Name / Number
1-9
10-24
28”
25-49
50-99
100+
Manufacturer Name / Number
1-9
10-24
36”
25-49
50-99
100+
TIME Procurement List Bid Document
August 30, 2010
Page 14
22 lb
Manufacturer Name / Number
1-9
10-24
39”
25-49
50-99
100+
Manufacturer Name / Number
1-9
10-24
42”
25-49
50-99
100+
Manufacturer Name / Number
1-9
10-24
45”
25-49
50-99
100+
Manufacturer Name / Number
1-9
10-24
48”
25-49
50-99
100+
Manufacturer Name / Number
1-9
10-24
60”
25-49
50-99
100+
Manufacturer Name / Number
1-9
10-24
66”
25-49
50-99
100+
Manufacturer Name / Number
1-9
10-24
72”
25-49
50-99
100+
TIME Procurement List Bid Document
August 30, 2010
Page 15
Manufacturer Name / Number
1-9
10-24
78”
25-49
50-99
100+
10. RED RETROREFLECTIVE FLAGS
Flags are to be 18” x 18” or 24” x 24” bright red/orange, and are to be made of polyester, vinyl-coated
nylon or long-wearing knitted vinyl. Flags should come fasted to a rigid handle 24”, 30” or 36” in length.
The free edge of the flag is to be weighted.
Red Retroreflective Flag
18” x 18” Flag
24” x 24” Flag
24”
30”
36”
24”
30”
36”
Handle
Handle
Handle
Handle
Handle
Handle
Type
Manufacturer
Name / Number
Cost Each
Cost for Each Case
of 50
11. ROAD FLARES
Road flares must conform to Underwriters Laboratory UL912 and DOT and ICC specifications. Flares
shall be coated in protective wax and have a lifetime limited warranty. Burn time shall be approximately
30 minutes or longer. Flares may come with a wire stand or without a stand.
LED flares must have a minimum crush resistance of 20,000 pounds. LED flares can use alkaline
batteries or be rechargeable. If rechargeable, the charger must come with each flare unless otherwise
priced below. Rechargeable battery life must be a minimum of 10 hours between charges. LED flares
must be available in red and amber.
Type
Road Flares - No
Stand
Road Flares
Road Flares LED Flares Stand
Alkaline
LED Flares Rechargeable
Manufacturer Name /
Number
1
2
3-4
Cost (Each)
5-9
by Quantity
10-24
25-35
36-71
TIME Procurement List Bid Document
August 30, 2010
Page 16
Manufacturer Name /
Number
1-19
Cost (Case
20-49
of 36) by
50-99
Quantity
100 +
Manufacturer Name /
Number
1-19
Cost (Case
20-49
of 72) by
50-99
Quantity
100 +
Manufacturer Name /
Number
LED Charger
1+
Cost (Each)
TIME Procurement List Bid Document
August 30, 2010
Page 17
PERSONAL SAFETY PRODUCTS
12. FLASHLIGHTS AND FLASHLIGHT WAND
Flashlights shall have a 10 watt bulb with an adjustable beam from spot to flood. Functions are
recessed, push button, self-cleaning and with a 3-position switch (on/off/blink). The flashlights shall be
made of anodized machined aluminum with knurled design. All must have a minimum 125 Lumen LED
output and a minimum 51,700 Peak Beam Candlepower. Flashlights are water and shock resistant, are
0-ring sealed throughout, and come with a battery pack (where stated). Please include flashlight
lengths in the bid price.

Rechargeable Flashlights - shall have a 5-cell (1/2-D) Nickel-Cadmium battery pack and a 60
minute run time per charge.

Wind Up Flashlights - shall run for a minimum of 30 minutes with a one minute windup.
Flashlights shall come equipped with three LED bulbs and shall not require a battery.

Standard Battery Flashlights - shall produce power and light as stated above with a standard
size battery.

Flashlight Wand - shall be able to be attached to a standard flashlight to direct and signal
traffic. The tip of the wand shall be open to allow a direct beam of white light.
Type
Length
Flashlights and Flashlight Wands
Manufacturer Name /
Flashlights / Flashlight
Number
Wand
Rechargeable
Wind Up
Cost
(Each)
by Type
Standard
Wand
TIME Procurement List Bid Document
August 30, 2010
Page 18
13. LIGHTED TRAFFIC WANDS
Lighted traffic wands can be utilized to direct motorists away from a scene or potential hazards. These
wands are especially useful at night and during inclement weather. All wands shall be visible for no less
than one-quarter (1/4) mile. Shall have knurled handle to allow for better grip.
Large LED wands shall be about 21” in length (including the handle). There should be a minimum of 6
LEDs per wand and each should take 2-C or 2-D size batteries. Compact wands shall be 16” in length
(including the handle). Wands shall have a minimum of 4 LEDs and shall accept 2-C or 2-D size
batteries. All wands shall be available in red or amber. Wands shall have settings of off, steady burn,
and flash. A carrying case may be provided at a separate cost.
Type
Cost
(Each)
by Size
Lighted Traffic Wands
21” Full Wand
16” Compact Wand
Without
Without
With Batteries
With Batteries
Batteries
Batteries
Manufacturer
Name / Number
Red
Manufacturer
Name / Number
Amber
Manufacturer
Name / Number
Carrying Case
14. BARRICADE TAPE
Tape shall be made of a non-adhesive polyethylene material and be applicable for both indoor and
outdoor use.
Barricade tape shall be available in yellow or red with reflective or non-reflective text. Non-reflective text
shall be all black. Reflective text shall be either all black or alternate between black and silver. Each roll
of tape shall be 3” wide and 1000 feet in length. Wording options shall be CAUTION, DANGER,
POLICE LINE, and RESTRICTED AREA.
Cost
(Each)
per
Quantity
by Type
Type
Quantity
Manufacturer Name / Number
1-9
10-24
Yellow
25-49
Reflective
50-99
100 +
Manufacturer Name / Number
1-9
10-24
Yellow Non25-49
Reflective
50-99
100 +
TIME Procurement List Bid Document
August 30, 2010
Caution
Barricade Tape
Danger
Police Line
Restricted Area
Page 19
Manufacturer Name / Number
1-9
10-24
Red Reflective
25-49
50-99
100 +
Manufacturer Name / Number
1-9
10-24
Red Non25-49
Reflective
50-99
100 +
15. PANTS
Pants must be Class E ANSI/ISEA 107-2004 compliant. The material is waterproof polyurethane coated
200-210 denier nylon or a polyester/mesh. Reflective bands are 3M Scotchlite reflective 9710 or 8725
or comparable. Pants shall be visible from a minimum distance of 1,000 feet. Each pant leg has elastic
at the waist and ankles and a minimum of 2” wide silver reflective tape for high visibility. Pants are
available in multiple material types and colors as outlined in the table below.
Material
Color
Pants
Manufacturer Name
and Number
Pants
Orange
Yellow
Polyester/Mesh
White
Silver
Lime
Fluorescent Orange
Fluorescent Yellow
Fluorescent White
Fluorescent Silver
Fluorescent Lime
Cost
(Each)
Orange
Yellow
Polyurethane
White
Silver
Lime
Fluorescent Orange
Fluorescent Yellow
Fluorescent White
Fluorescent Silver
Fluorescent Lime
TIME Procurement List Bid Document
August 30, 2010
Page 20
16. PERSONAL PROTECTION BEACONS
All personal protection beacons shall come with a LED bulb and have a 3-way switch for steady burn,
flashing or off functions. All beacons shall be visible for up to one mile at night.
Arm/ankle bands require 2032 lithium watch battery which will be sold separately unless otherwise
stated. Bands are shock proof and weather resistant. Bands shall be available in red, white and amber.
Bands shall be available in regular size (10”-15”) or large size (13”-22”).
LED batons shall weigh no more than 0.5 pounds each. Batons shall be available in green, red, blue or
yellow. An optional baton stand or belt holster shall be available
LED safety lights shall have an adjustable strap or belt holster. The mounting bracket should be
detachable but provide easy attachment to clothing, belts or equipment. The light shall require 2 AAA
batteries which are not included unless otherwise stated. LED safety lights are shock proof and weather
resistant. Lights shall be available in red, white or amber.
Color
Personal Protection Beacons
Manufacturer Arm/Ankle Manufacturer
Manufacturer LED Safety
LED Baton
Name / Number
Band
Name / Number
Name / Number
Light
Red
White
Amber/
Yellow
Green
Cost Blue
(Each)
Baton
Stand
Baton
Holster
Adjustable
Strap
Belt
Holster
TIME Procurement List Bid Document
August 30, 2010
Page 21
17. VESTS (CLASS II)
Class II Vests meet either ANSI/ISEA Class II 107-2004 or ANSI/ISEA Class II 207-2006.
 Class II 107-2004 - vests with or without messages shall be available in sizes: Small – 5-XL
 Class II 207-2006 - vests with or without messages shall be available in sizes: Small – 5-XL
Refer to the Worker Visibility Rule (23 CFR Part 634) for the visibility rule. Refer to ANSI Standard 1072004 or ANSI Standard 207-2006 for vest dimensions and specifications.
See sizing chart below for approximate chest and length sizes. Each chest size may be a few inches
smaller.
Sizing
Size
Chest
Length
Arm Hole
Side Vent Width
1. Small
36”-38”
40”-42”
44”-46”
24”
26”
27”
28”
28”
28”
5”
5”
5”
48”-50”
52”-54”
56”-58”
60”-62”
64”-66”
27”
28”
29”
29”
30”
28”
28”
28”
6”
6”
6”
2. Med
3. Large
4. XL
5. 2-XL
6. 3-XL
7. 4-XL
8. 5-XL
Vests shall also be available in 5 point tear away. Vests can be ordered with or without a message on
the back of the vest.
Type
Message
Manufacturer
Name / Number
Small
1072004
107-2004
Tear
Away
Message
1072004
Class II Vests
107-2004
207Tear
2006
Away
No Message
207-2006
Tear
Away
Message
2072006
207-2006
Tear
Away
No Message
Medium
Large
Cost
(Each)
by
Size
X-Large
2X-Large
3X-Large
4X-Large
5X-Large
TIME Procurement List Bid Document
August 30, 2010
Page 22
18. VESTS (CLASS III)
Class III vests meet ANSI/ISEA Class III 107-2004 standards.
Class III vests are available with or without a message on the back in sizes Medium – 5-XL. Sizing
charts and additional specifications as listed in Section 12 Class II Vest are applicable.
Type
Manufacturer
Name / Number
Class III Vests
107-2004
Manufacturer
Message
Name / Number
107-2004
No Message
Medium
Large
Cost (Each)
by Size
X-Large
2X-Large
3X-Large
4X-Large
5X-Large
19. RAIN JACKETS/PARKA
Rain jackets/parkas must be compliant with ANSI 107-2004 Class III specifications. Jacket color shall
be a combination of orange and lime. Jacket must be coated with weather resistant polyurethane. A
hood shall be zip off or zip out with a drawstring; zip out hoods shall be contained in the collar. There
shall also be a drawstring on the bottom of the jacket. Jackets shall have an inner liner and there shall
be multiple pockets.
Rain jackets/parkas are to be available in sizes Medium - 5-XL. Sizing charts and additional
specifications are listed in Section 16 - Class II Vests.
Type
Manufacturer
Name / Number
Class III Rain Jackets/Parkas
Manufacturer
Zip Off Hood
Name / Number
Zip Out Hood
Medium
Large
X-Large
Cost (Each)
by Size
2X-Large
3X-Large
4X-Large
5X-Large
TIME Procurement List Bid Document
August 30, 2010
Page 23
20. WINDBREAKERS
Windbreakers must be compliant with ANSI 107-2004 Class III specifications. Jacket color shall be a
combination of orange and lime. Jacket must be coated with weather resistant polyurethane. A hood
shall be zip off or zip out with a drawstring; zip out hoods shall be contained in the collar. There shall
also be a drawstring on the bottom of the jacket. Jackets shall have an inner liner and there shall be
multiple pockets.
Windbreakers are to be available in sizes Medium - 5-XL. Sizing charts and additional specifications
are listed in Section 16 - Class II Vests.
Type
Cost (Each)
by Size
Manufacturer
Name / Number
Class III Windbreakers
Manufacturer
Zip Off Hood
Name / Number
Zip Out Hood
Medium
Large
X-Large
2X-Large
3X-Large
4X-Large
5X-Large
21. WINTER (BOMBER) JACKETS
Winter (bomber) jackets must be compliant with ANSI 107-2004 Class III specifications. Jacket color
shall be a combination of orange and lime. Jacket must be coated with weather resistant polyurethane.
A hood shall be zip off or zip out with a drawstring; zip out hoods shall be contained in the collar.
Jackets shall have multiple pockets. Winter (bomber) jackets shall have an inner liner; liner may or may
not be removable. Removable liner can be worn alone and must be compliant with ANSI 107-2004
Class II or Class III specifications.
Winter (bomber) jackets are to be available in sizes Medium - 5-XL. Sizing charts and additional
specifications are listed in Section 16 - Class II Vests.
Type
Class III Winter (Bomber) Jackets
Class II Removable
Class III Removable
Non-Removable Liner
Liner
Liner
Zip Off
Zip Out
Zip Off
Zip Out
Zip Off
Zip Out
Hood
Hood
Hood
Hood
Hood
Hood
Manufacturer
Name / Number
Medium
Large
Cost
(Each)
by Size
X-Large
2X-Large
3X-Large
4X-Large
5X-Large
TIME Procurement List Bid Document
August 30, 2010
Page 24
22. VEHICLE BEACON LIGHTS
Vehicle beacon lights shall be available with LEDs. A minimum of 6 LEDs is required. Beacons must
work in temperatures ranging between 34o C and 55o C. The light shall be contained within a thick
metal case that is durable in all weather, waterproof, and resists corrosion. Working power is 50W
maximum; working current is 3.5A maximum. The beacon shall use 12V or 24V DC power. The
approximate size of the beacon shall be 6.50”D by 5.25”H. These dimensions may vary.
A 10’ (minimum) cord to connect with the vehicle’s 12V (cigarette lighter) outlet must be included with
each beacon light. Beacon lights shall have a magnetic base to mount to the vehicle. J-Bolt hardware
shall also be available as an alternative mounting option.
Beacon lights shall be available with red, blue, amber and clear LEDs. Beacons shall be able to rotate
and/or flash with multiple different modes.
Type
Color
Vehicle Beacon Lights
Manufacturer
Manufacturer
Manufacturer Rotating
Name /
Rotating
Name /
Flashing
Name /
and
Number
Number
Number
Flashing
Red
12V
Cost
(Each)
by
Type
Blue
Amber
Clear
Red
24V
Blue
Amber
Clear
TIME Procurement List Bid Document
August 30, 2010
Page 25
TRAFFIC SIGNS
23. REFLECTIVE PRISMATIC SHEETING
Reflective sheeting is intended to provide a higher level of standard brightness at long, medium and
short distance viewing ranges. Sheeting can be applied to standard traffic sign substrates with a hand
or pneumatic squeeze roller applicator. Sheeting shall be available in multiple colors in High Intensity
Grade (meets ASTM D4956 Spec Type III, Class 1), High Intensity Grade Prismatic (meets both ASTM
D4956 Type III and Type IV specifications), and Diamond Grade (Exceeds ASTM D4956 Spec Type IX
standards). Sheeting shall be clearly visible at viewing angles of 30 degrees or more.
Reflective Prismatic Sheeting
Grade
High
Manufacturer
Manufacturer High Intensity Manufacturer Diamond
Intensity
Name / Number
Name / Number Grade Prismatic Name / Number Grade
Grade
Blue
Cost Brown
(Per Clear
Square Green
Foot) Orange
by
Red
Color White
Yellow
24. RIGID ROAD SIGNS
Road signs meet MUTCD specifications for highway use and are to be made of aluminum a minimum
of 0.080” thick. Corners shall have a slight radius and there are to be pre-punched mounting holes a
minimum of 3/8” in diameter.
Signs are made of either new or recycled materials and are to be available in the following reflectivity
grades:
 High Intensity Grade (Meets ASTM D4956 Spec Type III, Class I)
 High Intensity Grade Prismatic (Meets both ASTM D4956 Type III and Type IV specifications)
 Diamond Grade (Exceeds ASTM D4956 Spec Type IX standards)
The table below provides available messages:
Sign Message
Be Prepared to Stop
Bump
Bumps
Detour Ahead*
Dip
Double Reverse Curve Symbol Right
Double Reverse Curve Symbol Left
Emergency Scene Ahead
End Road Work
Flagger Symbol
TIME Procurement List Bid Document
August 30, 2010
Color(s) Available
Pink
Orange
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Page 26
Fresh Oil
Grooved Pavement
High Water
Left Reverse Curve Symbol
Left Reverse Turn Symbol
Loose Gravel
Low Shoulder
Merge Symbol
Mowing Operations Ahead
No Center Stripe
One Lane Road Ahead
Pavement Width Transition Symbol (LEFT)
Pavement Width Transition Symbol (RIGHT)
Ramp Closed Ahead*
Paint Convoy Ahead
Right* Lane Closed Ahead*
Right Reverse Curve Symbol
Right Reverse Turn Symbol
Right* Shoulder Closed
Right* Shoulder Closed Ahead*
Right* Two Lanes Closed Ahead*
Road Closed Ahead*
Road Machinery Ahead*
Road Narrows
Road Work Ahead*
Rough Road
Soft Shoulder
Shoulder Drop Off
Shoulder Work Ahead
Signal Ahead
Stop Ahead
Survey Crew
Symbol Left
Symbol Right
Traffic Emergency Ahead
Transition Symbol Left
Transition Symbol Right
Two-Way Traffic Symbol
Uneven Lanes
Uneven Lanes Symbol
Wet Paint
Workers Symbol
Yield Ahead (Word Message)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
* For sign message texts with asterisk, any of the following overlays can be substituted for “RIGHT” or “AHEAD,” as a standard sign message
upon request: LEFT, CENTER, 2 MILES, 1 MILE, ½ MILE, 1500 FT, 1000 FT, or 500 FT.
TIME Procurement List Bid Document
August 30, 2010
Page 27
Rigid Road Signs
Grade
Cost
(Each)
by
Quantity
High
Intensity
Grade
High Intensity
Grade
Prismatic
Diamond
Grade
High Intensity
Grade
Recycled
High Intensity
Grade Prismatic
Recycled
Diamond
Grade
Recycled
Manufacturer
Name / Number
1-199
200 +
25. DETOUR SIGNS
Detour signs meet MUTCD specifications for highway use and are to be made of aluminum a minimum
of 0.080” thick. Corners shall have a slight radius and there are to be pre-punched mounting holes a
minimum of 3/8” in diameter.
Signs are made of either new or recycled materials and are to be orange and black. Signs available in
the following reflectivity grades:
 High Intensity Grade Prismatic (Meets both ASTM D4956 Type III and Type IV specifications)
 Diamond Grade (Exceeds ASTM D4956 Spec Type IX standards)
The following detour signs and sign sizes shall be available:
 Detour (MUTCD sign M4-8)
 Detour with Arrow Below (MUTCD sign M4-9)
o 24” x 12”
o 30” x 24”
o 30” x 15”
o 48” x 36”
o 60” x 48”
 End Detour (MUTCD sign M4-8a)
o 24” x 18”
 Arrow with Detour Inside (MUTCD sign M4-10)
o 48” x 18”
Grade
Detour
(M4-8)
Quant
24x12
30x15
Detour Signs
End
Detour with Arrow Below
Detour
(M4-9)
(M4-8a)
24x18
30x24
48x36
60x48
Detour
Inside Arrow
(M4-10)
48x18
Manufacturer
Name / Number
Cost
(Each)
by
Quantity
High
Intensity
Grade
1-199
200+
Manufacturer
Name / Number
Diamond
Grade
1-199
200+
* All dimensions in inches.
TIME Procurement List Bid Document
August 30, 2010
Page 28
26. ROLLUP SIGNS AND STAND
Rollup signs are convenient for incident management personnel to store in their vehicles for easy
access when incidents occur. Signs are available in 36” or 48” sizes. 48” width must be used in
freeway and expressway applications and in all locations with posted speeds above 45 mph.
The signs must meet MUTCD standards and NCHRP 350 compatibility crash test requirements. Signs
shall be able to withstand winds up to 65 mph and shall have four corner pockets. The frame is to be
made of aluminum and steel construction with a wind relieving system. Legs shall be telescoping
aluminum with at least two position height adjustments and anti-skid foot pads. The minimum height
from the ground is 12”. Signs shall come with a flag bracket and two 18” vinyl flags. Additional flags and
flag brackets may be purchased separately.
Signs are available in fluorescent coral (pink) or fluorescent orange with black text or graphics.
Corner pocket options are:
 Delta Pocket: ¾” deep, easiest to deploy, tough Lexan plastic, narrow width (rolls up smaller),
and has 3 rivets for better holding power
 Full Pocket: Full depth, tough Lexan plastic
 Half Pocket: 1” depth, easier to deploy, tough Lexan plastic
Reflectivity options are:
 High Intensity Grade (Meets ASTM D4956 Spec Type III, Class 1)
 High Intensity Grade Prismatic (Meets both ASTM D4956 Type III and Type IV specifications)
 Diamond Grade (Exceeds ASTM D4956 Spec Type IX Standards)
 Diamond Grade Fluorescent
Please Note: Reference Section 23, Rigid Road Signs, for a list of available sign messages.
Fluorescent Coral (Pink) Signs
The following prices apply for all 3 of the corner pocket options. Prices shall be provided for the sign
itself as well as for the sign and stand together. Storage bags need to be purchased separately.
Grade
Fluorescent Coral (Pink) Rollup Signs
High Intensity Grade
/ Prismatic
Stand Not
Stand Included
Included
Manufacturer Name / Number
Cost
(Each)
by Size
36” Sign
Manufacturer Name / Number
48” Sign
TIME Procurement List Bid Document
August 30, 2010
Page 29
Fluorescent Orange Signs
The following prices apply for all 3 of the corner pocket options. This price is for the sign only and
does not include the stand - stands and storage bags must be purchased separately.
Fluorescent Orange Rollup Signs
High Intensity Grade
Diamond Grade
/ Prismatic
/ Fluorescent
Stand Not
Stand Not
Stand Included
Stand Included
Included
Included
Grade
Manufacturer
Name / Number
Cost
(Each)
by Size
36” Sign
Manufacturer
Name / Number
48” Sign
Stand, Storage Bag and Flags/Flag Bracket
Stand, Storage Bag and Flag/Flag Bracket
Manufacturer Name /
Item
Item
Number
Cost (Each)
Stand
Storage Bag
Flag Bracket with Flags
Flag Bracket
Additional Flags
27. FOLD AND ROLL SIGN SYSTEMS
Fold and roll sign systems are convenient for incident management personnel to store in their vehicles
for easy access and deployment when incidents occur. Signs are available in 36” or 48” sizes. 48”
width must be used in freeway and expressway applications and in all locations with posted speeds
above 45 mph.
The signs must meet MUTCD standards and NCHRP 350 compatibility crash test requirements. Signs
shall be able to withstand winds up to 65 mph. The frame is to be made of aluminum and steel
construction with a wind relieving system. Legs shall be telescoping aluminum with at least two position
height adjustments and anti-skid foot pads. Legs should be equipped with an easy to use kick-release
system. The minimum height from the ground is 12”.
Sign panel shall be collapsible to accommodate the fold and roll system. Sign panels shall be
detachable or additional Velcro overlay patches shall be available to alter the sign message. Signs shall
come with a flag bracket and two 18” vinyl flags. Additional flags and flag brackets may be purchased
separately.
Signs are available in fluorescent coral (pink) or fluorescent orange with black text or graphic
messages.
TIME Procurement List Bid Document
August 30, 2010
Page 30
Reflectivity options are:
 High Intensity Grade (Meets ASTM D4956 Spec Type III, Class 1)
 High Intensity Grade Prismatic (Meets both ASTM D4956 Type III and Type IV specifications)
 Diamond Grade (Exceeds ASTM D4956 Spec Type IX Standards)
 Diamond Grade Fluorescent
Please Note: Reference Section 23, Rigid Road Signs, for a list of available sign messages.
Please reference Section 27 for individual prices on spring stands.
Fluorescent Coral (Pink) Signs
Prices shall be provided for the sign itself as well as for the sign and stand together. Prices shall also
be provided for the sign, stand and storage bag together. However, storage bag prices shall be
provided separately if bags need to be purchased separately or if additional bags are required.
Fluorescent Coral (Pink) Fold and Roll Sign Systems
Grade
High Intensity Grade / Prismatic
Stand Not
Stand Included
Stand & Bag Included
Included
Manufacturer
Name / Number
Cost
(Each)
by Size
36” Sign
Manufacturer
Name / Number
48” Sign
Fluorescent Orange Signs
Prices shall be provided for the sign itself as well as for the sign and stand together. Prices shall also
be provided for the sign, stand and storage bag together. However, storage bag prices shall be
provided separately if bags need to be purchased separately or if additional bags are required.
Fluorescent Orange Fold and Roll Sign Systems
Grade
Stand Included
High Intensity Grade / Prismatic
Stand Not Included
Stand & Bag Included
Manufacturer
Name / Number
Cost
(Each)
by Size
36” Sign
Manufacturer
Name / Number
48” Sign
TIME Procurement List Bid Document
August 30, 2010
Page 31
Storage Bag and Flag/Flag Brackets
Item
Storage Bag and Flag/Flag Brackets
Manufacturer Name /
Number
Item
Storage Bag
Cost (Each)
Flag Bracket with Flags
Flag Bracket
Additional Flags
28. ROLL-UP SIGN SPRING STANDS
The spring stands must meet MUTCD standards and NCHRP 350 compatibility crash test
requirements. Signs shall be able to withstand winds up to 65 mph. The frame is to be made of
aluminum and/or steel construction with a wind relieving system. Legs shall be telescoping aluminum
with at least two position height adjustments and anti-skid foot pads. Legs should be equipped with an
easy to use kick-release system. The minimum height from the ground is 12”. Sign stands shall be able
to hold 36” and 48” signs.
Spring stands for roll-up signs shall be offered with different spring types. Spring types shall be:
 Dual Torsion Springs
 Single Upright Coil Spring
 Dual Heavy Duty Steel Coil Spring
Item
Roll-Up Sign Spring Stands
Manufacturer Rollup Sign
Manufacturer Fold and Roll Sign
Name / Number
Stand
Name / Number
System Stand
Dual Torsion Spring
Cost Single Upright Coil Spring
(Each)
Dual Heavy Duty Steel Coil
Spring
29. SLOW / STOP PADDLES
Slow/Stop paddles are to be MUTCD compliant, octagonal, made of aluminum and are printed with
letters a minimum of 6” high. STOP is to have a red background with white letters and border. SLOW is
to have an orange background with black letters and border.
Paddles are to be available in High Intensity Grade (Meets ASTM D4956 Spec Type III, Class 1), High
Intensity Grade Prismatic (Meets both ASTM D4956 Type III and Type IV specifications), Diamond
Grade (Exceeds ASTM D4956 Spec Type IX standards) and Diamond Grade Fluorescent.
Paddles shall be available in two sizes as follows:


18” paddles
24” paddles
TIME Procurement List Bid Document
August 30, 2010
Page 32
Paddles shall come with a pre-attached handle. An additional plastic handle, either 60” or 72” in length,
shall be available. Prices shall be provided for the sign with additional plastic handles. Prices shall also
be provided for the sign and additional plastic handles separately.
Grade
Cost
(Each)
by Size
Manufacturer
Name / Number
Slow/Stop Paddles and Handles
High Intensity /
Manufacturer
Prismatic
Name / Number
Grade
Diamond
Grade /
Fluorescent
18” Sign w/
60” Handle
18” Sign w/
72” Handle
24” Sign w/
60” Handle
24” Sign w/
72” Handle
18” Sign
24” Sign
60” Handle
72” Handle
TIME Procurement List Bid Document
August 30, 2010
Page 33
OTHER
30. BATTERIES
Batteries are required provide a reliable energy supply for equipment and must provide sufficient
voltage, between charging, to each of the lamps to provide at least 15 days of continuous operation, in
any mode, at full daytime intensity. The following table provides an overview of all batteries available:
Most
Common
Name
Nominal
Voltage (V)
AA
AA NiMH
AAA
AAA NiMH
1.5
1.2
1.5
1.2
Cylinder
Cylinder
Cylinder
Cylinger
C
1.5
Cylinder
D
1.5
Cylinder
3 Volt (CR-V3)
3
Rectangul
ar
Has size and shape of two side-by-side AA batteries.
9 Volt
9
Rectangul
ar
Many (not all) 9 V batteries are an array of 6 reversed-polarity
(nub is negative while can is positive) AAAA cells welded
together internally.
Marine Battery
12
Rectangul
ar
Deep Cycle, Top Post, Spiral Gel Cell.
A marine deep cycle battery is different than a car battery
because it can be drained and re-charged multiple times.
6
Square
6
Square
Lantern
(Spring)
Lantern
(Screw)
CR-200
6
L-16
(D Deep Cycle)
6
CR2032
3
NiMH Battery
Charger
TIME Procurement List Bid Document
August 30, 2010
Shape
Rectangul
ar
Rectangul
ar
Coin
Comments
Rechargeable battery
Rechargeable battery
Can be replaced with alkaline AA cell using plastic sabot (stub
case).
Can be replaced with alkaline AA cell using plastic sabot (stub
case).
Springs are usually made so that leads for screw top can be
fastened to them. In most applications this is fine (see next).
For uses that have high vibration/shock where the leads may be
knocked off springs.
GC-2 group Deep Cycle for PCMS - 200A
Dimensions -10.25L 7.13W 10.5H.
Deep Cycle for HAR Radio; 340+Amps; Dimensions -11 5/8L
7W 17H 106Lb.
Standard Discharge Current: 0.2 mA. Maximum discharge
current: 3 mA. Maximum pulse discharge current: 15 mA.
Common battery in computers to keep the date and CMOS
settings current when power is off.
Must accommodate both AA and AAA NiMH batteries; must hold
a minimum of 2 batteries at a time
Page 34
Type
Batteries
Manufacturer Name
and Number
Batteries
AA
AA NiMH
AAA
AAA NiMH
C
D
3 Volt (CR-V3)
Cost (Each)
by Type
9 Volt
Marine
Lantern – Spring
Lantern – Screw
CR-200
L-16 (D Deep Cycle)
CR2032
NiMH Battery Charger
31. VEHICLE CONSPICUITY TAPE
Vehicle conspicuity tape should meet NHTSA's rule under 49 CFR, Part 571 for enhanced visibility and
detection, and also meet all FMVSS 108 Requirements. Coefficients of reflectivity for the white and red
sections at 0.2° observation angle and -4° entrance angle will exceed the values of 250 and 45
candlepower/foot candle/square foot, respectively, when sections cleaned with soap and water. Tape
should be durable for 7 years. Tape is available in high intensity grade or diamond grade.
Available Colors
 White / Silver
 Red
 Alternating
White / Silver
and Red
Available Lengths
 30 feet
 150 feet
TIME Procurement List Bid Document
August 30, 2010
Available Heights
 2 inches
 1 inch
Available Widths for
Alternating Tape
(white/red)
 6 inch/6 inch
 7 inch/11 inch
Page 35
Height
Grade
Vehicle Conspicuity Tape
High Intensity Grade
2”
1”
Diamond Grade
Cost (Each) by Quantity and Dimensions
1”
2”
Length
Quantity
Solid
White/Silver
Solid
Red
6” White or 7” White or
Silver/6”
Silver/7”
Red
Red
Manufacturer Name / Number
1-9 Rolls
30 ft
10-24 Rolls
25+ Rolls
Manufacturer Name / Number
1-9 Rolls
150 ft
10-24 Rolls
25+ Rolls
Manufacturer Name / Number
1-9 Rolls
30 ft
10-24 Rolls
25+ Rolls
Manufacturer Name / Number
1-9 Rolls
150 ft
10-24 Rolls
25+ Rolls
Manufacturer Name / Number
1-9 Rolls
30 ft
10-24 Rolls
25+ Rolls
Manufacturer Name / Number
1-9 Rolls
150 ft
10-24 Rolls
25+ Rolls
Manufacturer Name / Number
1-9 Rolls
30 ft
10-24 Rolls
25+ Rolls
Manufacturer Name / Number
1-9 Rolls
150 ft
10-24 Rolls
25+ Rolls
TIME Procurement List Bid Document
August 30, 2010
Page 36