SCORPION Z6
Alarm Controller
User
Instructions
Using the Scorpion Z6 alarm controller
PIN Numbers (user codes)
Scorpion Z6 is capable of storing up to twelve PIN numbers. Each of these PIN numbers may be two to four
digits in length and each may be used to arm or disarm the system.
The Keypad Beeper
The Scorpion Z6 signals system status through the keypad beeper. During an arming cycle the beeper will
sound for the entire exit time. This is a ‘leave now’ warning. Scorpion Z6 will arm at the expiry of this
period. On entry, the beeper sounds for the programmed entry period. If a valid user code is entered to
disarm the system, the beeper emits two short tones. An incorrect entry is signalled by one long tone.
The Status (yellow) Lamp
The yellow status lamp is used to indicate several conditions.
Yellow lamp on:
Yellow lamp off:
Yellow lamp flashing:
the system is armed or arming
the system is disarmed
an alarm has occurred; a system fault exists or
the panic function has been activated
The ‘Mains’ Lamp
The ‘Mains’ lamp is on when mains power is applied. After a mains failure of more than 12 minutes, the
‘Mains’ light flashes until mains power is restored and an arm/disarm cycle is completed. The ‘Mains’ lamp
also flashes to indicate a low battery condition. When the battery is restored to full charge and an arm/disarm
cycle is completed, the ‘Mains’ lamp stops flashing.
The ‘Armed’ Lamp
The ‘Armed’ lamp illuminates when the system is armed. The ‘Armed’ lamp also flashes to indicate when an
alarm condition has occurred.
Two Key Panic
If this function has been programmed into the Scorpion Z6 it may be activated by pressing the keypad * and #
keys simultaneously. A panic activation may be cancelled by entering any valid user code then #.
To Arm the System:
Quickarm:
you.)
Alternatively:
enter 1 then # (this is a technician selectable option. Ask your installer to advise
enter a valid two, three or four digit user code then #.
If all zones are clear, the keypad sounds a sequence of two short beeps for the duration of the exit delay, the
yellow status lamp turns on. The lamps for all zones to be armed are also turned on.
If an alarm condition exists during arming, the lamp(s) for those zone(s) flash and are accompanied by a
sequence of two long beeps. This indicates that one or more of the zones are faulty or not secure.
To Disarm the System:
Enter a valid two to four digit user code then #. The keypad will beep twice and the yellow status light will
turn off. A flashing yellow status lamp indicates that one or more zones has been alarmed. To determine the
zone that has alarmed, press 8 1 then # on your keypad, note the flashing zone lamp number and check this
against the installer’s zone listing on the inside of the keypad door. Notify your installer or security company.
To determine the cause of an alarm condition, press 8 3 then # on your keypad. The flashing zone lamp indicates the
type of alarm condition that has occurred:
Zone 1 lamp flashes
Zone 2 lamp flashes
Zone 3 lamp flashes
Zone 4 lamp flashes
Zone 5 lamp flashes
Alarm caused by a nitewatch panic
Alarm caused by a keypad panic
Low battery condition
Power failure condition
Communications failure
To Arm the System and Exclude a Zone:
Enter a valid user code then * followed by the zone number to be excluded, then press #.
To Change, Remove or Enter a User Code:
Enter either of the two master user codes. Your installer would have set these up for you. Then press [1+3]
together, two beeps will be heard. Enter the new user code and press the # key, one beep will be heard. Enter
the single digit code of the user that is to be added or changed (0 - 9). Two beeps signal a successful entry,
one long beep a failed entry. To remove a user, omit entering a new user code then press the # key.
To Cancel a Fire Alarm Activation:
Enter a valid user code then #.
To Arm the System in Night Mode:
Enter 9 1 then #. Scorpion waits for the pre-programmed delay then arms those zones selected for night
arming. When a zone is activated in night mode Scorpion signals a pre-activation warning prior to alarming.
To deactivate the system during the pre-alert, enter your user code then #.
To Disarm the System in Night Mode:
Enter a valid user code then #.
Nitewatch Station (if connected):
To nitearm the system, simply press the ‘Armed’ key on the Nitearm station . If the system is armed by
Nitewatch and an activation occurs, the system can only be disarmed at the alarm keypad by entering a valid
user code then #. To generate an alarm condition from Nitewatch, press the two ‘emergency’ keys
simultaneously.
To Turn on/off Chime Mode:
Enter 7 1 then #. Each time a sensor is activated while the system is disarmed and chime mode is turned on,
the keypad beeps for approximately five seconds. In this mode Scorpion acts as a door or area minder.
IMPORTANT: This alarm system must be tested weekly to maintain system integrity.
TELECOM WAIVER
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that
the item complies with the minimum conditions for connection to its network. It indicates no endorsement of
the product by Telecom, not does it provide any sort of warranty. Above all, it provides no assurance that any
item will work correctly in all respects with another item of Telepermitted equipment of a different make or
model, nor does it imply that any product is compatible with all of Telecom’s network services.
This equipment is set up to carry out test calls at pre-determined times. Such test calls will interrrupt any
other calls that may be set up on the line at the same time. The timing set for such test calls should be
discussed with the installer. The timing set for test calls from this equipment may be subject to ‘drift’. If this
proves to be inconvenient and your calls are interrupted, then the problem of timing should be
discussed
with the equipment installer. The matter should NOT be reported as a fault to Telecom Faults Service.
GUARANTEE
1.
Subject to clause 2 below, Micron guarantees this product against defects in materials and workmanship for a period
of 12 months from the date of delivery to the purchaser as follows:
(a) Micron will repair or replace free of charge any goods or part thereof found to be defective by reason of faulty
material
or workmanship.
(b) The purchaser must give Micron notice of the alleged defect within 14 days of it becoming apparent and must
return the defective goods or part thereof to Micron.
2.
This guarantee does not apply or extend to:
(a) Any product altered or repaired by any person other than Micron so as in Micron’s sole judgement to adversely
affect the product.
(b) Damage, malfunction or failure arising from accident, misuse or misapplication, neglect, modifications, use of
unauthorised replacement parts or accessories, exceeding the specific ratings, improper voltage or connection of
any wire to any part of the circuit board other than the terminal block.
(c) Any product where the rating label or serial number is removed or altered.
(d) Any consequential or indirect loss.
Designed and Manufactured by:
MICRON GROUP HOLDINGS LTD
P O Box 78-006, Grey Lynn
Auckland, New Zealand
Phone: 64-9-378 6098
Fax: 64-9-378 6454
Internet: http://www.micron.co.nz