Bid Specification Sheet
1000W/1200W "Rama" 175 FFT PC
This is a specification for a 175mm Fast
Focus Technology PC luminaire,
complete with all accessories.
Description
The PC luminaire shall be purpose designed for
performance lighting applications.
Equipment Details
The PC luminaire shall be supplied complete with
high temperature and impact resistant
engineering plastic colour frame and hook clamp.
A short form instruction manual shall also be
supplied with the PC luminaire. A detailed
instruction manual shall be available for download
from the manufacturer’s website.
Technical Performance
The PC luminaire shall comply with the
international safety standards EN60598/IEC598.
POWER INPUT VOLTAGE
The PC luminaire shall be able to be operated to a
maximum power input voltage of 240V.
LAMP WATTAGE
The PC luminaire shall be able to use up to a
1200W lamp.
LAMP BASE
The PC luminaire shall be supplied with a GX9.5
bi-pin lamp base.
POWER SUPPLY CABLE
The PC luminaire shall be supplied with a 1.2
metre long temperature resistant silicon rubber
cable. There shall be three conductors of a
1.5mm diameter within. The power supply cable
point of entry to the PC luminaire shall be a
trumpet gland constructed from high temperature
resistant engineering plastic. There shall be no
direct clamping pressure on the cable, and a
separate IEC plug and connector shall not be
acceptable. The power supply cable shall be
retained by two separate indirect pressure points
located within the cable connector compartment.
WEIGHT
The PC luminaire shall not exceed 8.7kgs in
weight, including the barndoor accessory and
colour frame.
PAGE 1
SIZE
The PC luminaire shall have the following
dimensions:
Height: 445mm, Width: 286mm, Length: 480mm
Lamp House Construction
The lamp house of the PC luminaire shall have
rounded corners and edges with no sharp edges.
It shall be constructed from aluminium, and
engineering plastic.
The sides of the PC luminaire shall be constructed
from extruded aluminium for strength, lower
weight and no noise during the expansion and
contraction period when the PC luminaire is
heating up. Sides constructed from sheet metal
shall not be accepted. Ventilation of the PC
Luminaire shall maximised by not less than five
convection slots running the entire length of the
lamp house.
The front and rear of the PC luminaire shall be
constructed from high temperature and impact
resistant engineering plastic mouldings for
strength, lower weight and no noise during the
expansion and contraction period when the PC
luminaire is heating up. Front and rear castings
constructed of metal shall not be accepted.
There shall be a rear grab handle mounted on the
rear of the PC luminaire. The grab handle shall be
constructed from high heat and impact resistant
engineering plastic, and shall have a warning
label formed as an integral part of the handle.
There shall be a cable connector compartment
located on the outside back moulding of the PC
luminaire. The power supply cable shall be
terminated in this compartment and not in the
main body of the luminaire. For ease of service it
shall be possible to gain access to the interior of
the cable connector compartment by the removal
of two screws and the cable connector
compartment cover.
Paint / Finish
The paint finish of the PC luminaire shall be low
reflective, matt charcoal colour, electrostatically
applied, baked on epoxy powder coat. The finish
of all exterior plastic components shall be matt
charcoal colour.
www.seleconlight.com
Optical System
The PC lens shall be 175mm in diameter with a
light diffusion around its convex edge for softening
the beam edge; mounted inside the luminaire and
fully supported around its entire circumference.
Stainless steel springs shall hold the lens in
position and allow for movement caused by heat
expansion.
focus position of the luminaire or the barndoor
accessory shall not be accepted.
The lamp access shall be by means of a side
hinged bottom tray held closed with a spring clip
assembly. The hinge design shall be incorporated
in the shape of the lamp house side extrusion,
and shall run the length on the lamp house for
strength and rigidity.
The PC luminaire shall have a spherical reflector,
manufactured from 99.99% super pure aluminium
anodised and polished to provide a pure specular
reflector.
AUTOMATIC DISCONNECTION
The lens and reflector shall be quickly accessed
for cleaning without tools in the lamp housing by
means of a side hinged bottom tray held closed
with a spring clip assembly. It shall possible to
clean the lens and reflector of the PC luminaire
without altering the set focus position.
SAFETY ANCHOR POINT
Performance
It shall be possible to adjust the balance of the PC
luminaire by repositioning the yoke as required
along the length of the luminaire. There shall be a
balance point marked on the focus reference
scale.
The PC luminaire shall comply with the following
performance specifications when using a T/29
1200W 230V lamp:
Beam Angle: (2:1 variation from centre peak) 5°60° with minimum light output:
4.5° - 342,000cd
62° - 14,220cd
Operation
The PC luminaire shall have the following
operational features:
PAN
The PC luminaire shall incorporate Fast Focus
Technology in its pan operation. It shall be
possible to pan the luminaire with one hand, and
without the aid of tools. The operator shall be able
to unlock the yoke pan release lever and move
the yoke in one easy movement.
The mains power shall be automatically
disconnected when the lamp access tray is
opened.
The PC luminaire shall incorporate an integral
safety bond that shall be able to be retracted into
the luminaire when not in use. The safety bond
shall be rated for the weight of the luminaire.
BALANCE
ACCESSORY SLOT
The PC luminaire shall have three accessory slots
for positioning of a safety mesh, colour frame and
barndoor accessory. The accessories shall be
retained in the PC luminaire with an accessory
slot cover. A spring retention clip shall not be
accepted.
Accessories
The PC luminaire shall come supplied with the
following accessories:
COLOUR FRAME
The PC luminaire shall incorporate a locking
clamp disc with a spring-loaded variable pressure
clutch system for controlled movement of tilt
operation. The operator shall be able to loosen
the tilt locking clamp disc with a ¼ turn of the
locking clamp disc knob, tilt the PC luminaire with
one hand, and then lock the PC luminaire in place
with a ¼ turn of the locking clamp disc knob.
The colour frame shall be constructed from high
heat and impact resistant engineering plastic for
safety, to minimise weight, and to provide
maximum cooling for the plastic colour filter
medium. The colour frame shall have no sharp
edges and shall be of hinged construction to
enable the colour filter medium to be replaced
quickly. The interior of the colour frame shall be of
rough texture to securely grip the colour filter
medium. Colour frame accessories constructed
from folded sheet metal shall not be accepted.
FOCUS
BARNDOOR
TILT
The PC luminaire shall incorporate Fast Focus
Technology in its focus operation. It shall be
possible to focus the luminaire with one hand. The
operator shall be able to grip the focus control
lever and adjust the focus in one easy movement.
Focus systems requiring the screwing of a focus
knob or wormscrew mechanism shall not be
accepted.
PRE-FOCUS REFERENCE
The PC luminaire shall have reference scales on
all axis of movement to comply with stage lighting
visualization software packages.
The four-leaf barndoor shall be constructed from
high heat and impact resistant engineering plastic
and lightweight steel sheet for each leaf. It shall be
possible to rotate the barndoor leaves 360° to
facilitate the beam masking. The leaf tension shall
be adjustable to suit the operator’s preference.
The barndoor shall have safety chain anchor
points provided which are integral to the barndoor
mounting plate.
SAFETY MESH
There shall be a lens safety mesh available for the
PC luminaire.
The reference scales shall comprise:
Pan focus scale with degrees marked in
increments from the centre line of the luminaire.
Warranty
Tilt reference scale with degrees marked in
increments from the centre line of the luminaire.
The PC luminaire shall be supplied with a limited
three-year warranty when used in normal
theatrical applications.
Focus reference scale with the beam angle
degree marked in increments from 4.5° to 62°.
LAMP ACCESS
It shall be possible to access the lamp of the PC
luminaire without the need of tools and without
altering the focus position of the luminaire or the
barndoor accessory. Lamp access that alters the
PAGE 2
Full warranty details shall available for download
from the manufacturer’s website at:
www.seleconlight.com
www.seleconlight.com