MATERIAL SAFETY DATA SHEET
International Stoneworks, Inc.
Seal & Go® Enhancer W
Section I - Product Identification
Product Name:
Seal & Go® Enhancer W
Distributed by:
International Stoneworks, Inc., 2523 Fairway Park, Ste. 510, Houston, TX 77092
(713) 956-8291
Section II - Components
Ingredient
Fluorochemical Sealer
Water-Based Enhancer
Concentrate
2-Butoxyethanol
Deionized water
CAS#
Trade Secret
Wt.%
---
OSHA PEL
N/E
ACGIH TLV
N/E
Trade Secret
111-76-2
7732-18-5
--<5%
>75%
N/E
25 ppm
N/A
N/E
25 ppm
N/A
Section III - Health Hazard Data
Chronic Effects of Overexposure: No known applicable information.
Acute Effects of Overexposure:
Ingestion: May irritate stomach and intestines. May be aspirated into lungs if swallowed, resulting in
pulmonary edema and chemical pneumonitis.
Skin: Mild irritant.
Inhalation: May cause headache, dizziness, nausea, unconsciousness.
Eye: Mild irritant
Section IV - Emergency First Aid Procedures
Ingestion: Do not induce vomiting. Call Poison Control Center. Consult a physician.
Inhalation: Move to fresh air. If unconscious, give artificial respiration, and seek medical attention.
Eye Contact: Immediately flush with large amounts of water for at least 15 minutes and call a physician.
Skin Contact: Wash affected areas with water for 15 minutes. Remove contaminated clothing and
launder before reuse. Wash with soap and water.
Section V - Fire and Explosion Data
Flash Point (closed cup): >230°F
Auto Ignition: N/D
Extinguishing Agents: Dry Chemical, Carbon Dioxide, Foam or Water Spray
Special Fire Fighting Procedure: Evacuate personnel to safe area. Avoid breathing decomposition
products. Shut off source, if possible. Use NIOSH/MSHA approved self-contained breathing apparatus
and full protective clothing. Use water spray to cool nearby containers and structures exposed to fire. Use
water spray to disperse vapors. Try to cover liquid spills with foam. Avoid spraying water directly into
containers due to eliminate the danger of boilover. Extinguish all nearby sources of ignition.
Hazardous Decomposition Products: Carbon dioxide, carbon monoxide, hydrogen fluoride.
Unusual Fire and Explosion Hazards: None.
Section VI - Accidental Release Measures
Soak up with compatible absorbent, which should be placed in closed containers outdoors.
Section VII - Handling and Storage
Keep away from heat, sparks, and flames. Store in a cool, dry, well-ventilated place away from
incompatible materials. Wash thoroughly after handling. Do not get in eyes, on skin, or clothing.
Section VIII - Exposure Control and Personal Protection
Ventilation: General ventilation is adequate. Do not aerosolize.
Protective Gloves: Chemical resistant gloves should be worn.
Eye Protection: Chemical safety goggles.
Respirator: Wear a NOISH-approved respirator.
Section IX - Physical/Chemical Characteristics
Form: Liquid
Appearance: Milky white
Specific Gravity (water = 1): 1.1
Solubility In Water: Soluble,
Evaporation (Butyl Acetate = 1): > 1
Odor: Mild Pungent
Boiling Point: N/D
Water Reactive: None
pH: 4.5
Section X - Stability and Reactivity
Stability: Stable - Polymerization will not occur
Conditions to Avoid: N/A
Incompatibility (materials to avoid): strong
oxidizing agents and strong alkalis
Section XI - Toxicological Information
Please call the non-emergency number under Section I if information is required.
Section XII - Ecological Information
Please call the non-emergency number under Section I if information is required.
Section XIII - Disposal Considerations
Dispose of product only by methods approved by federal, state, and local regulations.
Section XIV - Transport Information
For transportation accidents call CHEMTREC® 1-800-424-9300.
Special shipping information: Not regulated by DOT
Section XV - Regulatory Information
This product is in compliance with the U.S. Toxic Substances Control Act (TSCA) inventory requirement.
Section XVI - Other Information
Format and Preparation Complies with ANSI Z400.1-1993
Revision Date: 04-15-2004. Supercedes any prior versions.
We believe said statements, technical information and recommendations contained herein are
reliable. Statements contained herein are given without warranty or guarantee of any kind,
express or implied, and we assume no responsibility for any loss, damage, or expense, direct or
consequential, arising out of their use.
MATERIAL SAFETY DATA SHEET
International Stoneworks, Inc.
Klean & Go
Section I - Product Identification
Product Name:
Klean & Go
Distributed by:
International Stoneworks, Inc., 2523 Fairway Park, Ste. 510, Houston, TX 77092
(713) 956-8291
Section II - Components
Ingredient
Sodium Metasilicate
2-Butoxyethanol
Proprietary Surfactants
Deionized water
CAS#
6834-92-0
111-76-2
Trade Secret
7732-18-5
Wt.%
<5%
<6%
-->80%
OSHA PEL
N/E
25 ppm
N/A
N/A
ACGIH TLV
N/E
N/E
N/A
N/A
Section III - Health Hazard Data
Chronic Effects of Overexposure: No known applicable information.
Acute Effects of Overexposure:
Ingestion: May cause burns to mouth and throat.
Inhalation: Mist may seriously irritate nose, throat and lungs.
Eye Contact: May cause severe eye burns.
Skin Contact: May cause burns with possible injury and tissue destruction.
Section IV - Emergency First Aid Procedures
Ingestion: Do not induce vomiting. Call Poison Control Center. Consult a physician.
Inhalation: Move to fresh air, get medical attention if irritation persists.
Eye Contact: Flush thoroughly with water for 15 minutes, get medical attention.
Skin Contact: Flush thoroughly with water for 15 minutes. If burns persist, get medical attention. Launder
affected clothing before rewearing.
Section V - Fire and Explosion Data
Flash Point (closed cup): Non-flammable
Autoignition Temp: Not applicable
Extinguishing Agents: Product is not flammable. Use water, carbon dioxide, dry powder extinguisher, or
other media appropriate for materials actually involved in fire.
Hazardous Decomposition Products: Thermal decomposition may produce carbon dioxide, carbon
monoxide.
Section VI - Accidental Release Measures
Procedure for Cleanup: Prevent further spill of material, contain material already spilled.
Section VII - Handling and Storage
Store out of reach of children. Keep container closed and store in a cool dry location. Avoid freezing or
extended storage in high temperature.
Section VIII - Exposure Control and Personal Protection
Ventilation: Normal room ventilation satisfactory. Respirator not normally required.
Protective Gloves: Avoid skin contact. Wear NBR or rubber gloves for extended or repeated skin contact
with concentrate.
Eye Protection: Avoid eye contact. Wear safety glasses while handling concentrate.
Footwear and Clothing: Standard work shoes and clothing.
Other: Do not ingest product. No other special protective measures required.
Section IX - Physical/Chemical Characteristics
Form/Color: Liquid/slight yellow
Boiling point: 100°C
Specific Gravity (water = 1): 1.07
Vapor Pressure, mm Hg/20 Deg C: 760 mm/Hg
Evaporation rate (Butyl Acetate = 1): N/D
pH: 11.5-12.5
Odor: Mild
Section X - Stability and Reactivity
Stability: Yes
Incompatibility: Avoid strong oxidizing materials, acids.
Reactivity, and under what conditions: None known.
Section XI - Toxicological Information
Please call the non-emergency number under Section I if information is required.
Section XII - Ecological Information
Please call the non-emergency number under Section I if information is required.
Section XIII - Disposal Considerations
Dispose of product only by methods approved by federal, state, and local regulations.
Section XIV - Transport Information
For transportation accidents call CHEMTREC® 1-800-424-9300.
Special shipping information:
Compoundings, cleaning liquid (metasilicate), 8
NA 1760, PG III
Section XV - Regulatory Information
This product is in compliance with the U.S. Toxic Substances Control Act (TSCA) inventory requirement.
Section XVI - Other Information
Format and Preparation Complies with ANSI Z400.1-1993
Revision Date: 04-15-2004. Supercedes any prior versions.
We believe said statements, technical information and recommendations contained herein are
reliable. Statements contained herein are given without warranty or guarantee of any kind,
express or implied, and we assume no responsibility for any loss, damage, or expense, direct or
consequential, arising out of their use.
MATERIAL SAFETY DATA SHEET
International Stoneworks, Inc.
Tile & Grout Restorer
Section I - Product Identification
Product Name:
Tile & Grout Restorer
Distributed by:
International Stoneworks, Inc., 2523 Fairway Park, Ste. 510, Houston, TX 77092
(713) 956-8291
Section II - Components
Ingredient
Urea Hydrochloride
Proprietary Surfactants
Deionized water
CAS#
506-89-8
Trade Secret
7732-18-5
Wt.%
<50%
-->50%
OSHA PEL
N/E
N/A
N/A
ACGIH TLV
N/E
N/A
N/A
Section III - Health Hazard Data
Chronic Effects of Overexposure: No known applicable information.
Acute Effects of Overexposure:
Ingestion: This product may be harmful or fatal if ingested.
Inhalation: Inhalation of mist during manufacturing may irritate mucous membranes.
Eye Contact: Eye contact will be painful and irritating.
Skin Contact: Prolonged and repeated skin exposure may be irritating.
Section IV - Emergency First Aid Procedures
Ingestion: Do not induce vomiting. Call Poison Control Center. Consult a physician.
Inhalation: Remove to fresh air, if unconscious, give artificial respiration and seek medical attention.
Eye Contact: Immediately flush with large amounts of water for at least 15 minutes and call a physician.
Skin Contact: Remove contaminated clothing and launder before reuse. Wash with soap and water.
Section V - Fire and Explosion Data
Flash Point (closed cup): Non-flammable
Auto Ignition: Not applicable.
Fire and Explosion Hazards: At temperatures above 140°F acid action on most metals may release
hydrogen, a highly flammable and explosive gas.
Extinguishing Agents: Dry Chemical, Carbon Dioxide, Foam or Water Fog, No direct water stream.
Special Fire Fighting Procedure: Evacuate personnel to safe area. Avoid breathing decomposition
products. Shut off source, if possible. Use NIOSH/MSHA approved self-contained breathing apparatus
and full protective clothing.
Hazardous Decomposition Products: Thermal decomposition may yield carbon monoxide, carbon
dioxide, nitrogen oxides, hydrogen chloride. Hydrogen gas may be released upon contact with certain
metals.
Section VI - Accidental Release Measures
Eliminate all ignition sources. Contain spill and salvage as much material as possible. Pick up the
remaining material with an absorbent.
Section VII - Handling and Storage
Handling And Storage Precautions: Keep away from heat, sparks, and flames. Store in a cool, dry, wellventilated place away from incompatible materials. Do not store over 95ºF (35ºC).
Wash thoroughly after handling. Do not get in eyes, on skin, or clothing.
Repair And Maintenance Precautions: Do not cut, grind, weld or drill on or
near container.
Section VIII - Exposure Control and Personal Protection
Ventilation: General ventilation is adequate.
Protective Gloves: Chemical resistant gloves should be worn.
Eye Protection: Chemical safety goggles, eyewash unit nearby
Respirator: Wear a NOISH- approved respirator
Section IX - Physical/Chemical Characteristics
Form: Liquid
% Solids: 30%
Appearance: Light amber clear
Specific Gravity (water = 1): 1.21
Solubility In Water: 100%
Odor: Mild
Boiling Point: 100° C
pH: 1
Section X - Stability and Reactivity
Instability: Metal contact may cause Hydrogen release.
Incompatibility (materials to avoid): Do not mix with metal powders. Do not mix with bases.
Section XI - Toxicological Information
Carcinogenicity: None
Please call the non-emergency number under Section I if information is required.
Section XII - Ecological Information
Please call the non-emergency number under Section I if information is required.
Section XIII - Disposal Considerations
Dispose of product only by methods approved by federal, state, and local regulations.
Section XIV - Transport Information
For transportation accidents call CHEMTREC® 1-800-424-9300.
Shipping Information: Not regulated by DOT.
Section XV - Regulatory Information
This product is in compliance with the U.S. Toxic Substances Control Act (TSCA) inventory requirement.
Section XVI - Other Information
Format and Preparation Complies with ANSI Z400.1-1993
Revision Date: 04-15-2004. Supercedes any prior versions.
We believe said statements, technical information and recommendations contained herein are
reliable. Statements contained herein are given without warranty or guarantee of any kind,
express or implied, and we assume no responsibility for any loss, damage, or expense, direct or
consequential, arising out of their use.