Material Safety Data Sheet
U.S. Department of Labor
Complies with OSHA Hazard Communication
Standard, 29CFR 1910.120
Occupational Safety and Health Administration
(Non-Mandatory Form)
PolyMaster Retrofoam Foam Insulation
IDENTITY (As used on Labeling):
Section I - General Information
Manufacturer:
(See Note below)
PolyMaster, Inc.
10523 Lexington Drive
Knoxville, TN 37932
NOTE: PolyMaster is a distributor and is not the manufacturer of the product
described under this MSDS. This MSDS is based on information supplied to
PolyMaster from the manufacturer, therefore PolyMaster cannot warrant the
accuracy of information contained in this MSDS.
.
Emergency Telephone
Number:
1-(800) 580-FOAM
Telephone Number
for Information:
(865) 966-3005
Date prepared/revised:
01/09/2009
Section II - Identity Information / Hazardous Ingredients
POLYMASTER PLASTIC FOAM INSULATION
Hazardous Ingredients (Specific Chemical Identity/ CAS Number
OSHA PEL
ACGIH TLV
Other Limits
None.
DOT NAME: Not regulated, Solid N.O.S.,
PERSONAL PROTECTION: None required
NFPA:
Health = 0; Fire = 1; Reactivity = 0; Special Hazards = 0
IARC: None.
(0 = none; 1 = Slight; 2 = Low; 3 = Moderate; 4 = Extreme)
Section III - Physical /Chemical Properties
Boiling Point:
Not Applicable (solid)
Bulk Density:
0.75 lbs/cu ft
Vapor Pressure:
Not Applicable
Melting Point:
N/A
Vapor Density:
Not Applicable
pH:
N/A
Solubility in Water:
Insoluble
Decomposition:
High temperature
Appearance and Odor:
Rigid White foam.
Section IV - Fire and Explosion Hazard Data
Flash Point:
None
Flammable Levels (LEL/UEL): Not Flammable, Meets Class I
Extinguishing Media:
As required by fire
Unusual Fire/Explosion Hazards: Will decompose at high
temperature
01 MSDS Foam 10/08cpe
Material Safety Data Sheet
U.S. Department of Labor
Complies with OSHA Hazard Communication
Standard, 29CFR 1910.120
Occupational Safety and Health Administration
(Non-Mandatory Form)
Section V - Reactivity Data
Stability:
Unstable ( )
Stable
(X)
Incompatibility (materials to avoid):
Conditions to avoid: Contact with freshly prepared foam may
cause eye, skin, or respiratory irritation - wash liberally with
water.
Strong caustic or acid.
Hazardous Decomposition or Byproducts:
Hazardous Polymerization:
- will occur ( ) - will not occur (X)
Conditions to Avoid: Ammonia, oxides of carbon and
nitrogen, formaldehyde, and hydrogen cyanide may be
liberated during high temperature decomposition.
Section VI - Health Hazard Data
Routes of Entry:
Inhalation:
Yes (dust, vapor)
Skin:
Yes (dust)
Ingestion:
Induce vomiting if swallowed.
Health Hazards (Acute and Chronic): None.
Toxicity: None
Carcinogenicity:
IARC:
IARC Monographs:
OSHA/EPA:
Signs and Symptoms of Exposure:
No
None
No
Irritation (i.e. dusts)
Medical Conditions Generally Aggravated by Exposure: None known.
Emergency and First Aid Procedures: None. Use normal safety precautions.
Section VII - Precautions for Safe Handling and Use
Steps to be taken if material is released or spilled:
foam.
Use a dust mask and gloves when sweeping up residuals of
Waste Disposal Method: Dispose of foam as solid waste in accordance with local regulations. Material is not regulated
under DOT or Federal regulations.
Precautions to be Taken in Handling and Storage: Dusts may be irritating. Avoid breathing dusts.
Other Precautions: None
Nuissance Dust: Exposure limits, OSHA / ACGIH 10 mg/m3
01 MSDS Foam 10/08cpe
Material Safety Data Sheet
U.S. Department of Labor
Complies with OSHA Hazard Communication
Standard, 29CFR 1910.120
Occupational Safety and Health Administration
(Non-Mandatory Form)
Section VIII - Control Measures
Respiratory Protection:
Dust mask, (dusts)
Ventilation Type Required:
None
Protective Gloves:
Eye Protection: Safety glasses. (dusts)
Other Protective Clothing or Equipment (specify Type):
Work/Hygienic Practices:
Gloves (dusts)
None. Coveralls recommended.
As a general precaution, do not eat, smoke or drink when handling materials.
Section IX – Regulatory Statements
DOT Shipping Name:
Regulation under TSCA:
Not regulated.
None of the ingredients are regulated under TSCA.
Regulation under SARA Title III:
Regulation under OSHA:
Not regulated.
None.
Other Statements:
The information in this data sheet have been assembled by the manufacturer based on its own
studies and on the work of others. The manufacturer makes no warranties, express or implied, as to the accuracy,
completeness or adequacy of the information herein. Neither the manufacturer or PolyMaster shall be liable (regardless
of fault) to the vendee, the vendee’s employees, or others, for any direct, indirect, special, or consequential damages
arising out of, or in connection with the accuracy, completeness, adequacy or furnishing of such information.
01 MSDS Foam 10/08cpe