DIVISION 10 – SPECIALTIES
SECTION 10 28 13 – TOILET ACCESSORIES
Page 1 of 5
PART 1 - GENERAL
1.01
RELATED DOCUMENTS
1.
1.02
1.03
1.04
Drawings and general provisions of Contract, including General
Conditions and Division 1 Specification sections, apply to work of this
section.
DESCRIPTION OF WORK
1.
Extent of each type of toilet accessory is indicated on drawings and
schedules.
2.
Types of toilet accessories required include the following:
.1 Toilet Paper Holders.
.2 Mirrors.
.3 Soap dispensers.
.4 Sanitary Napkin Disposal Units.
.5 Sanitary Napkin Dispenser Units.
.6 Grab bars.
.7 Paper Towel Dispensers/Waste Receptacles.
QUALITY ASSURANCE
1.
Furnish inserts and anchoring devices which must be set in concrete
or built into masonry: coordinate delivery with other work to avoid
delay.
2.
Coordinate accessory locations with other work to avoid interference
and to assure proper operation and servicing of accessory units.
3.
Provide products of same manufacturer for each type of accessory
unit and for units exposed in same areas, unless otherwise
acceptable to Architect.
SUBMITTALS
1.
R- /14-15
Submit manufacturer's technical data and installation instructions for
each toilet accessory.
DIVISION 10 – SPECIALTIES
SECTION 10 28 13 – TOILET ACCESSORIES
Page 2 of 5
2.
Provide setting drawings, templates, instructions, and directions for
installation of anchorage devices in other work.
PART 2 - PRODUCTS
2.01
ACCEPTABLE MANUFACTURERS
1.
2.02
Products meeting project requirements, manufactured by the
following shall be acceptable:
.1 Bobrick Washroom Equip., Inc. – Clifton Park, NY (Bobrick)
.2 Bradley Corp. – Menomonee Falls, WI (Bradley)
.3 McKinney Parker – Scranton, PA (McKinney Parker)
.4 A & J Washroom Accessories – New Windsor, NJ (A&J)
.5 Royce Rolls Ringer Co. – Grand Rapids, MI (Royce Rolls)
MATERIALS, GENERAL
1.
Stainless Steel: AISI Type 302/304, with polished No. 4 finish, 22
gauge minimum, unless otherwise indicated.
2.
Brass: Leaded and unleaded, flat products, FS QQ-B-613; rods,
shapes, forgings, and flat products with finished edges, FS QQ-B-626
3.
Sheet Steel: Cold rolled, commercial quality ASTM A 366, 20 gauge
minimum, unless otherwise indicated. Surface preparation and metal
pretreatment as required for applied finish.
4.
Galvanized Steel Sheet: ASTM A 527, G60.
5.
Chromium Plating: Nickel and chromium electro-deposited on base
metal, ASTM B 456, Type SC 2.
6.
Mirror Glass: FS DD-G-451, Type I, Class 1, Quality q2, 1/4" thick,
with silver coating, copper protective coating, and nonmetallic paint
coating complying with FS DD-M-411.
7.
Galvanized Steel Mounting Devices: ASTM A 386, hot-dip galvanized
after fabrication.
8.
Fasteners: Screws, bolts, and other devices of same material as
accessory unit or of galvanized steel where concealed.
R- /14-15
DIVISION 10 – SPECIALTIES
SECTION 10 28 13 – TOILET ACCESSORIES
Page 3 of 5
2.03
2.04
FABRICATION
1.
Stamped names or labels on exposed faces of toilet accessory units
are not permitted. Unobtrusive labels on surfaces not exposed to
view are acceptable. Where locks are required for a particular type
of toilet accessory, provide same keying throughout project. Furnish
two keys for each lock.
2.
Surface-Mounted, Recessed or Semi-Recessed Toilet Accessories,
General: Except where otherwise indicated, fabricate units with tight
seams and joints, exposed edges rolled. Hang doors or access
panels with continuous stainless steel piano hinge. Provide concealed anchorage wherever possible.
TOILET PAPER HOLDER
1.
Roll Toilet paper holder shall be surface mounted double roll, 18
gauge, type 304 stainless steel frame, 20 gauge, 1 1/8” diameter
stainless tube with restriction adapter and Master Lock (all keyed
alike) model #STP-2 with lock, clip and sloped stainless steel top,
produced by Royce Rolls Ringer Company (1-800-253-9638). All
mounting to be with corrosion resistant, tamperproof, thru-bolted
‘sex’ type with mating male/female threads, flush on backside.
Install with additional 18 gauge stainless steel backplate to match
frame size when not mounted back to back through toilet partition
with another paper holder. Specify sloped top and additional
backplate when ordering.
Above Or Below – to be edited by designer – confirm with school
2.
2.05
Folded Toilet Paper holder shall be surface mounted Bobrick B-272,
Bradley 515, or A&J Washroom U807. All mounting to be with
corrosion resistant, tamperproof, thru-bolted ‘sex’ type with mating
male/female threads, flush on backside. Install with additional 18
gauge stainless steel backplate to match frame size when not
mounted back to back through toilet partition with another paper
holder.
MIRRORS
1.
R- /14-15
Mirrors shall be Bobrick B293 1836, Bradley 740-18x36, or McKinney
Parker 170T – 18 x 36.
DIVISION 10 – SPECIALTIES
SECTION 10 28 13 – TOILET ACCESSORIES
Page 4 of 5
2.06
SOAP DISPENSERS
1.
2.07
SANITARY NAPKIN DISPOSAL UNIT
1.
2.08
Sanitary napkin dispenser unit shall be equal to Bradley 426, Bobrick
B-2800, or McKinney Parker 873.
GRAB BARS
1.
2.10
Sanitary napkin disposal unit shall be equal to Bradley 4722-15,
Bobrick B254 or McKinney Parker 626.
SANITARY NAPKIN DISPENSER UNIT
1.
2.09
Horizontal soap dispenser shall be GOJO dispensers 1250ml, dove
gray, #5150
Grab bars shall be McKinney Parker Series 9600, Bradley Series 812,
or Bobrick Series B-6806.
SEMI-RECESSED TOWEL DISPENSER AND WASTE RECEPTACLES
1.
Towel dispenser and waste receptacle shall be stainless steel semirecessed equal to Bradley 2252-10, Bobrick B3942, or McKinney
Parker 80294-2x2.
PART 3 - EXECUTION
3.01
INSPECTION
1.
3.02
Installer must examine substrates, previously installed inserts and
anchorages necessary for mounting of toilet accessories, and other
conditions under which installation is to occur, and must notify
Contractor in writing of conditions detrimental to proper and timely
completion of work. Do not proceed with work until unsatisfactory
conditions have been corrected in manner acceptable to Installer.
INSTALLATION
1.
R- /14-15
Install toilet accessory units in accordance with manufacturer's
instructions, using fasteners which are appropriate to substrate and
DIVISION 10 – SPECIALTIES
SECTION 10 28 13 – TOILET ACCESSORIES
Page 5 of 5
recommended by manufacturer of unit. Install units plumb and level,
firmly anchored in locations indicated.
3.03
2.
Install concealed mounting devices and fasteners fabricated of same
material as accessories or galvanized steel.
3.
Install exposed mounting devices and fasteners finished to match
accessories.
4.
Provide theft-resistant fasteners for accessory mountings.
ADJUSTING AND CLEANING
1.
Adjust toilet accessories for proper operation and verify that
mechanisms function smoothly.
2.
Clean and polish all exposed surfaces after removing protective
coatings and labels.
END OF SECTION
R- /14-15